DG570MXW1 Frigidaire Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from Philipsburg, MT
- Parts Used:
- 5303281154, 5303212849
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
worn belt and squeaky bearring
remove the top and front of the dryer, then removed the idler assembly. This enabled me to rimove the belt form the drum and replace it and the idler assembly. Not difficult at all.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Justin from Hueytown, AL
- Parts Used:
- 5303281154
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
belt came off
removed front of drier , removed rear access panel, replaced the belt. reinstalled front of drier and rear access panel
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margery from Hartland, ME
- Parts Used:
- 5303281154
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
The drum belt was making a squealing noise, and it looked frayed.
Had to remove the front of the dryer but installation was quick and easy. An affordable and quick repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Prattsburgh, NY
- Parts Used:
- 5303281154, 5303212849
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Dryer drum would not turn.
The first part was the most difficult-opening the front of the dryer cabinet! Once open, the new belt was installed and then the new idler pulley was put in-place. The cabinet was closed-job done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gloria from Murfreesboro, TN
- Parts Used:
- 131825900
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
The dryer tub started screeching and then dropped.
Removed the top of the dryer above the dryer door by pulling the pop out plastic holds. I then removed the dryer plug in at the top inside dryer that controls the start when dryer door is closed. I thenremoved the screws that are located at the back of the dryer tub where the bearing is located. I then replaced the support bearing. I just replaced every thing I took off in reverse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Midlothian, VA
- Parts Used:
- 131825900
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
worn bearing
Taking apart cleaning putting back together I don't have any h-t lube so ill be doing it again. Thanks for the part ill be calling again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eugenio from Lewiston, ME
- Parts Used:
- 5303281154
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
belt squeking.
Replaced belt
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Hudson, NH
- Parts Used:
- 5303212849
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Bearings Went and Idler Roller fell apart, not allowing drum to turn
unbolted one bolt and replaced old unit with new unit....took only a few minutes. Part was supposed to arrive in 3 days, but arrived next day....thanks very much!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dominico from Westerly, RI
- Parts Used:
- 5303281154, 5303212849
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
Drum didn't turn
Removed small panel from back of Dryer,and removed Idler Pulley Assembly. From the front,lifted the top of Dryer to get access to the drum,disconnected the two wires for the Stop switch, removed the four screws, two on each side,and lowered down the front panel. Now,removed old belt and installed new, installed new Idler Pulley Assembly,aligned belt with Pulley.Reassembled the front and the top of the Dryer and I was done.The pulley was squeaking,but a shot of DW40 took care the problem.
Thanks
Domenico Intrieri
Thanks
Domenico Intrieri
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bryant from tolna, ND
- Parts Used:
- 5303212849
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer did not turn
put the new part on with ease took 5 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jurg from Los Angeles, CA
- Parts Used:
- 5303212849
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Old roller worn out
It was really easy to install the new roller with the newly designed side flange! All I had to do is hook in the tension spring. Works perfect again without the squeeking noise!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from Lancaster, OH
- Parts Used:
- 131825900
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
worn bearing, squeaking, scraping sound
I have used this company twice now and both times have been a good experience. Would highly recommend!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ron from waynesboro, VA
- Parts Used:
- 5303281154
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Broken Belt...measured 88" x 1/2" flat belt
The customer had removed the top cover hinges and the rear cover plate to recover the broken belt. I first removed the four screws holding the front panel and tilted it out to allow access for the new belt. The drum dropped about 2-3". Fed the new belt over the drum with the printing'This Side Up' facing me, lifted the drum up as I closed the front cover over the felt on the front rim of the drum. Replace dhtew four screws. Door switch leads were long enough to allow the front cover to tilt forward so did not remove. Next engaged the motor pully and tension pulley, then rotated the drum manually to assure tracking and no twist in the belt. Vacuumed the wall passthrough pipe,the flex vent tubing and the motor compartment of lint. Closed up the back cover and drove the 52 miles back to my shop.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Calvin from Las Vegas, NV
- Parts Used:
- 131825900
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench set
Symptoms suggested drum support bearing was problem.
Referred to Video and replaced drum support bearing as shown. Did not solve the problem as noise was still present. Called professional repairman, who replaced the belt pulley, along with all the parts I had just installed (came as part of a total kit). I was on the correct path, but just didn't go far enough to check out the belt pulley. If it should happen again, I could complete the whole repair process. Great learning process!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jon from Jenkins, KY
- Parts Used:
- 131825900
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
needed to replace drum bearing
took front panel off, removed access panel in rear to disconnect the belt from motor. removed top panel (this is a stack unit) take plastic rivets loose from lint trap, remove lint trap tube, pull drum out after slightly pulling up to dislodge drum from bearing cradle, Remove bracket and bearing from back of unit, clean parts of old grease (be carefull not to loose small ball bearing on back) Reassemble parts using moderate amount of new grease, put parts back together in reverse order.
Was this instruction helpful to you?
Thank you for voting!