DEH550T1 Frigidaire Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Edward from Lindenhurst, IL
- Parts Used:
- 5303281153
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Old bearing made noise. Grease was dry and worn out.
The video was very helpful. Glad I bought the entire kit. Dryer works great and no noise.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Witly from Wheatley Heights, NY
- Parts Used:
- 5303281153
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The only probelem was to take out the drum, because it was a washer and dryer combo. the dryer was on top, i did not have any room to pull out the drum
I remove the drum, and install the bearing just like the instructions in the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Hudson Falls, NY
- Parts Used:
- 5303281153
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
rear bearing on dryer was squeeking badly
I followed instructions I found on u-tube to remove the drum and belt and access the bad bearing and change it. The instructions were quite good other than needing to remove a small panel on the back of the dryer to pull the belt around the tensioner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Pensacola, FL
- Parts Used:
- 5303281153
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Squeaky noise from rear of dryer
Unplug dryer, remove rear access cover and removed belt from pulley. Remove bottom cover on front of dryer, remove top of dryer, unplug harness to control panel and remove front door assembly. Remove screws from drum to bearing assembly. Removed drum and belt removed bearing assembly by lifting up and out of the bearing socket. Vacuumed all the lint. Removed the bearing socket, installed all parts and covers in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amy from salem, OR
- Parts Used:
- 5303281153, 5303281153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The Rear drum bearing kit had sheared off
Exactly how the video showed! It was super easy and I am a girl...although I am a lil more mechanicly inclined than most girls, it was a piece of cake!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jurg from Los Angeles, CA
- Parts Used:
- 5303212849
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Old roller worn out
It was really easy to install the new roller with the newly designed side flange! All I had to do is hook in the tension spring. Works perfect again without the squeeking noise!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ron from waynesboro, VA
- Parts Used:
- 5303281154
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Broken Belt...measured 88" x 1/2" flat belt
The customer had removed the top cover hinges and the rear cover plate to recover the broken belt. I first removed the four screws holding the front panel and tilted it out to allow access for the new belt. The drum dropped about 2-3". Fed the new belt over the drum with the printing'This Side Up' facing me, lifted the drum up as I closed the front cover over the felt on the front rim of the drum. Replace dhtew four screws. Door switch leads were long enough to allow the front cover to tilt forward so did not remove. Next engaged the motor pully and tension pulley, then rotated the drum manually to assure tracking and no twist in the belt. Vacuumed the wall passthrough pipe,the flex vent tubing and the motor compartment of lint. Closed up the back cover and drove the 52 miles back to my shop.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Anchorage, AK
- Parts Used:
- 5303281154, 5303212849
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
Broken pulley & belt
Hired a professional!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Conrad from Schenectady, NY
- Parts Used:
- 5303281153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Loud squeaking noise when running dryer
It was super easy! I followed the PartSelect video and everything went fine. Getting the drum out of the machine was a bit tricky but once it was out, the rear bearing kit went in without any problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Fayetteville, AR
- Parts Used:
- 5303281153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
Loud whinning noise when drying first started up for a few minutes, then would stop
The repair was done by my spouse. We replaced the rear drum bearing. We installed with the instructions sent by parts select. They were very accurate. The total repair took about 1 and 1/2 hours that was only because we cleaned out the entire dryer also, by using an air compressor to clean and blow out all the lint built up. This improved drying time and the part stopped the noise. I don't recall exactly what tools were used besides screwdrivers. This was our first time to replace anything in our dryer of 12 years old. I feel that if you follow the instructions that anyone would be able to do this repair. We did the repair in our garage because you need the room to work on it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Trever from Vancouver, WA
- Parts Used:
- 5303281153
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dryer was making a squealing noise
The repair video from PartSelect.com was excellent in describing how to fix the dryer. All of the parts were included in the replacement kit, including the screws and ball bearing. I was very impressed with the quality of the kit and the video. A $25 kit probably saved me hundreds in repair cost and saved me from having to buy another dryer. Here's to another 14 years of use!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason from Champaign, IL
- Parts Used:
- 5303281153
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Loud Racket couming from the bearing casing
Ordered the part from PartSelect.com. It came in a couple of days, which was nice. My wife was all over me to fix the dryer, or buy a new one. Needless to say, I didn't think the old one was done. The bearing assembly had an instructional video. This provided easy to follow instructions, and simple advice even I could follow. Everything went well, and the dryer is now quietly running as good as new. Awesome website, and the customer service is excellant too. WE use PartSelect.com at work all the time. Im a property manager, and the parts and advice save us thousands every year. Thanks guys!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Clairton, PA
- Parts Used:
- 5303281153
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
the rear drum bearing broke
when the bearing broke the drum fell in the back. I tore the dryer apart, ordered the part and fixed it when the part came. the dryer runs like new now!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cheryl from Weirton, WV
- Parts Used:
- 5303281153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
loud squeek
followed the Video instruction which were provided. Dryer works like brand new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Centennial, CO
- Parts Used:
- 5303281153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Loud squeeking and vibration of the dryer drum.
I followed the directions sent by you step for step and the rpair was done in no time at all. Had a little trouble with the roller ball installation but figured out how to install it after a couple of tries. Repair was done with minimal use of standard houshold tools.
Was this instruction helpful to you?
Thank you for voting!