YEED4300VQ0 Estate Dryer - Instructions

Unplugged dryer, removed two screws from the lint trap area, pried up the top of the dryer to get to the switch, removed two screws securing the switch, unplugged the switch, plugged in the new one and reversed the procedure.

My 14 year old son did it as I supervised! Pulled the dryer out on a dolly, unpluged the dyer, removed 9 hex head screws to remove the back cover, removed and replaced the thermal fuse, located next to the exhust outlet, set the cover back on, moved the dryer back in with the dolly. I had the thermal fuse over nighted to me for a total price of $35, figured I saved at least $150 on a service call by Whirpool.

Removed and replaced terminal block, power cord and black wire to timer.

My wife was doing a load of laundry when she thought the the dry cycle was finished she found the cloths still wet. When she went to restart the dryer nothing. I did some research online and found the most common problem was the thermal fuse. I removed the back of the dryer removed the fuse and checked for continuity with my volt meter. I thought that I was going to find alot of lint build up. However I did not so I decieded to also replace the thermostat, using the thermo cut-off kit because this might have caused the fuse to fail. I ordered the parts from partselect and they arrived in two days. Partselect has excellent instructional videos on how to make the repair. It was quick and easy and saved the money of just going out and buying a new appliance.

Well - I'd taken my clothes out of the dryer and put them on the pool table and went upstairs to go to bed. I thought at last moment to go pee first and ran back down stairs. Downstairs I smelled the odor of burning lint. When I looked into the laundry room, my dryer was glowing red hot - Sweet! It seems that the heating element was staying on even though the dryer was off. I looked in the various descriptions of myriad failures of dryers and didn't find that one in the documentation at all. So - I replaced the thermal fuse, the Thermal cut-off and the timer. Alas - the replacement timer had to be replaced because the clock motor was defective. When the second replacement timer arrived, it was quickly installed. Long story short - if the timer is in any play mode, the heating element stay on full blast - not low, not medium, but full on chub - and this is whether the fan or tumbler are on or not, door open or not. And so the mystery anomaly remains un-repaired, unresolved and perhaps even, undiagnosed. Note - the new Thermal Cut Off does not cut off anything even when it cookin red hot. Strange.

I bought a belt from a store in my area- What a mistake...I found this site and read all the stories on how easy it was and how PartSelect.com had the parts in stock and had easy instructions...I put the idler pulley in place, put the belt in place (all from instructions included) and put the dryer back together (which was easy). I actually did it alone. I would recommend this company to anyone in need of their parts and help!

super fast shipping, got the part in two days, and had it done in 15-20 min, remove the front pannel, remove the belt and tenssioner,took the drum out , took the old rollers , lubed the shafts,replaced the old rollers with the new ones, intalled the drum back, the tenssioner and the new belt, reinstalled the front pannel, and done...easy and fast job, like new dryer, works nice...save some money...the new one will do the same..just dry the clothes.

First of all, you go in from the front. There a clip on each side that I just pried up to pop the front of the dryer up. A screw also needs to be removed in the lint catcher area. Also, two screws holding the door open switch must be removed as I never could get the electrical connectors to disconnect. No big deal. I had to figure out you must lift the front of the dryer up as the last two things holding it in are a prong on each side. Lift the front up and off and set it aside. As you do this the drum will either fall on your feet or you'll have it supported be another person or with something else. I used bungee cords and kept it in the laundry room. Cleaned out all the old lint, collected a few bucks in change. It took me awhile to figure out how the new belt routed through the removable pulley guide thing and around the wheel pulley. I don't remember right now as I'm not looking at it but remember pinching the belt and feeding it through the guide and around the wheel pulley which has a little slot and grooves matching the belt. Besides scrapping my wife's hand while she was helping me get the front of the dryer back on there were no casualties or further complications. Good luck!

I removed the discharge duct from the back of the dryer. Then, I removed the screws on the back of the dryer and the back itself. This exposed the cycling thermostat. I removed the screw holding the thermostat. I took the wires off the defective thermostat and reinstalled them on the new thermostat. Then, I reassembled in reverse order.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

I took a ¼ inch nut driver and removed the rear cover from the unit, and then used a continuity tester to determine which safety device was open. According to the schematic there was one non-resettable safety device in the heating circuit, and that was open. The kit that I ordered came with thermal cutoff and a thermostat. I replaced both parts and the unit now operates normally. While I had the dryer open I thoroughly cleaned the dust and lint from the unit and also the 4 inch vent pipe. I ordered this part on Friday morning and received it early Saturday afternoon.

Pryed the top off the dryer, unplugged the door switch, took the screws out of the front panel, then lifted the drum out. Placed the new belt around the drum and while my wife held it in place and steadied it, I reached underneath and looped the belt through (as per instructions), reassembled and back in business! Reaching under the drum was not that easy....VERY tight space to work in and there was no way I could get both hands through, I almost gave up, but one last try and a couple of good grunts, and it popped into place. Getting the wires back on the door switch was a bit of an ordeal too. Took about 30 mins. but still worth it. I'm sure I saved at least a $100 repair.

After my husband disassembled the cabinet and removed the drum, we used a putty knife to remove the old seal and carefully glued the new one in place. (A 2 man job to do it without leaking glue everywhere.) We then replaced the belt, following the picture sent by PartSelect and put everything back. (We put all small pieces in labeled envelopes so that putting it back together was easy.) Another helpful hint - take a few digital pictures beforehand in the event that you need to see it to put it back together!

Disconnected supply. Lifted top (hinges on rear). removed two 1/4 hex head screws retaining front panel. Disconnected door switch wires. Removed front panel, lifting off from bottom tabs. Lifted out drum and discarded broken belt. Spent 30 minutes+ cleaning interior, drum skid area, dryer exit tube, motor pulley, belt tensioner, etc, etc. Checked wiring harness for possible damage (no damage found). Repositioned drum skid pads, which had become dislodged from their intended position. Reinstalled the drum with new belt, ensuring both belt & tensioner were correctly positioned, and drum rollers and felt seals were also correctly positioned. Reinstalled front panel, tightening the two 1/4 hex head retaining screws. Reconnected power. Checked functionality. Closed top cover.

First, remove the back panel of dryer which is about 10 screws. Then remove the 2 thermal switches, one is above the heating element and the other is where the hot air comes out. They are both really easy to get to and the pictures on Part Select.com are identical, so you can order the part first and then just "match them up" if you are not sure what to replace. Oops, the first step is to unplug the dryer.