EIED50LIW0 Electrolux Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Harry from Republic, PA
- Parts Used:
- 134690800
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
The blower housing was cracked
I used utube on how to dismantle the dryer. In fact I use a video created by
Parts select. The hardest part was getting a spring that holds the tensioner on the drum belt.
Parts select. The hardest part was getting a spring that holds the tensioner on the drum belt.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from LOS ANGELES, CA
- Parts Used:
- 5304508449
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Doable with 2 people but it definitely took tiime
Once we got the dryer out of the cramped where we could work on it, the project went a little quicker. I'd recommend using paper plates/bowls, that you label, to hold all the screws for each piece you remove off the back. It doesn't seem like it will be a lot, but we had at least 20-30 screws in 4-5 different sizes. Unlike someone else's install, we had to completely pull the white back panel off, as well as the main back cover, due to one screw holding the air duct from the inside of the dryer compartment (meaning we couldn't reach everything from the back). Getting this screw out was a challenge and seemed like a huge design flaw, but if you can't get to that screw, the old air duct isn't coming out. There are 2 other screws holding the air duct but they're easy to reach once the back panel is off.
Once that was taken out the process was straightforward, we just took our time reattaching everything step-by-step. Now our dryer works like new.
Once that was taken out the process was straightforward, we just took our time reattaching everything step-by-step. Now our dryer works like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yvette from RUTHER GLEN, VA
- Parts Used:
- 134793600
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lint filter unusable due to age
Inserted lint filter into slot.
Replacement is exact match to original filter.
Replacement is exact match to original filter.
Was this instruction helpful to you?
Thank you for voting!
blower housing was in disrepair
removed top and front of dryer then removed the drum to expose the blower housing. then removed the damaged unit and replaced with the new unit . Then put it back together. The hardest part for me was putting the drum back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Hummelstown, PA
- Parts Used:
- 3204267
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Dryer Would Not Heat
I researched possible causes on line and watched a PartsSelect video on YouTube on how to test. I ended up misreading test results and ordered the High Limit Thermostat but subsequently realized problem was the Terminal Block. No problem, PartsSelect took back the Thermostat (I hadn't installed it) and shipped me the Terminal Block. My dryer was back up and running in less than 7 days from initial analysis to installation of Terminal Block. Instructions that came in confirmation email for installation were perfect and easy to follow. Total cost with new power cord from Home Depot was less than $50 vs a quoted service call of $175+ parts from local electrician.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas F. from Whitmire, SC
- Parts Used:
- 134813600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
clothes hanging-up during the drying cycle,leaving marks on the garments.
as on the video. so easy. took longer to clean-up
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from St Paris, OH
- Parts Used:
- 809160308
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
error code 63 I checked all componenets and wiring for resistance. everything checked ok. noticed charring on the copper contacts in the control board.
removed the top of the cabinet,unplugged wiring from control board, removed screws fastening control board and installed new control board.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- margaret from virginia beach, VA
- Parts Used:
- 134793600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed a new filter
i simply took the old one out and replaced it with the new one. it fit perfectly.
Was this instruction helpful to you?
Thank you for voting!