EIMGD55IIW4 Electrolux Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Tom from Essexville, MI
- Parts Used:
- 5303931775
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer ran, had no heat
Your website was very helpful in narrowing down and diaganosing the problem. A continuity tester verified an open solenoid. Ordered Sunday evening, parts arrived Tuesday. Ignition coils drop in place with a holddown bracket and one screw. Wiring harness is reattached. Front of dryer is put in place followed by the top. Plugged in the dryer (it is just commom sense to have the power off). Started dryer, of course it ran WITH heat. The end of the story is HAPPY WIFE, HAPPY LIFE. Happy to do business with you. Tom , MI
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Miles from Austin, TX
- Parts Used:
- 5303931775
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Dryer did not stay hot through complete cycle
This repair took about fifteen minutes. I popped the top of the dryer using a flat-blade screwdriver, leaned it back against the back wall, unscrewed two screws holding the front panel, removed the five electrical spade contacts after marking which went where, swung out the panel and lifted it off. After that, it was a simple job to unscrew the plate holding the solenoids in, at the bottom left of the unit. I replaced the solenoids, closed everything up and now the dryer is working better than it has in the last three years, or so. If your dryer is heating sporadically, the odds are 85%, or more, that a solenoid swap-out will correct the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TERRY from MILLSBORO, DE
- Parts Used:
- 134197700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Burner Bad
Ordered part received next day fast shipping was great part in and working thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Los Angeles, CA
- Parts Used:
- 5303931775
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dryer Won't Heat Up
Never knew I was handy, but I did it! I was reluctant to spend a couple $100 on a repair visit, so found this site and bought the coils I needed for only $26+tax. It's pretty easy. I just lifted up the top of the dryer with a screw driver, should snap open. Then unscrewed the front panel with two screws from the inside. Then located the old coils on the bottom left. The bracket that holds them is a little difficult to remove as you need to have a small philips screw driver to get the back one. But once I got that off, just unplugged the old ones and put the bracket back, then the panels and it WORKED. The only problem I have is that I didn't take the door switch off properly and now the dryer doesn't stop spinning if I open the door and want to check the clothes. So I may have to get someone in eventually.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Plymouth, IN
- Parts Used:
- 5303281135
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Heat would come on but not stay on.
Flame Sensor didn't fix it but, it was easy to replace. Unplug electric. Lift up the top and remove wires from switch and light switch. Remove screws that hold on the front and remove front panel by lifting up and out. Sensor is on the left side of the burner, held on with just one screw. EASY!
Was this instruction helpful to you?
Thank you for voting!