EIMED60JIW0 Electrolux Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mathew from CHELMSFORD, MA
- Parts Used:
- 5304508449
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Dryer was leaving marks on clothing
You must disconnect appliance from the gas, water and vent to access the back. Remove the top of the dryer which then allows you to remove the rear panel by removing all screws, You may also have to remove 2 electrical connections to get this panel off. Now you have access to the air duct. To remove the air duct there are 3 screws inside the dryer and 2 screws on the lower part of the air duct. One of the lower screws is facing toward the inside of the dryer and you will need a 12"+ screwdriver to be able to remove. Once you do all that install the new part and repeat steps in reverse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ann from WALLA WALLA, WA
- Parts Used:
- 3204267
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
lack of heat
Remove top lid by pushing tab on either side with a putty knife. Disconnect the 2 wire carriages on right. Remove one
phillips head screw on each side that holds front panel to dryer body. Remove front panel by using flat head screwdriver to pry panel from body. Remove thermostat located on bottom right attached to front of motor on a plastic body by removing two phillips head screws. Disconnect wires and place on new part.
phillips head screw on each side that holds front panel to dryer body. Remove front panel by using flat head screwdriver to pry panel from body. Remove thermostat located on bottom right attached to front of motor on a plastic body by removing two phillips head screws. Disconnect wires and place on new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- anthony from JASPER, GA
- Parts Used:
- 134792700
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
heater element went out
followed the instruction on you tube, the part was exact, there was nothing to guess, basically you take the whole front off of the dryer, that in itself is easy (follow instructions), once you get to the element, just plug and play. the worst part was a set screw in the back that did take some patience, but finally did get it in. I am not a mechanic in the least, trust me, if I can do it then anyone can. you will need regular Philips screw driver and one short one, really short, mine is about 2 inches in length, also I used manual one, allot of plastic, so I would not recommend electric drill or electric driver. also a good pair of plyers, but small not large.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Luis from JERSEY CITY, NJ
- Parts Used:
- 134705900, 5308027429
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The original seal was worn out so much so that it kept burning out my motor two Motors two years
I purchase one tube of heat resistant adhesive but I change both seals if you could afford to buy a second to I would recommend you do so the one tube just made it. For instructions on how to prepare the drum for installing new seals I went on YouTube
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yvette from RUTHER GLEN, VA
- Parts Used:
- 134793600
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lint filter unusable due to age
Inserted lint filter into slot.
Replacement is exact match to original filter.
Replacement is exact match to original filter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- margaret from virginia beach, VA
- Parts Used:
- 134793600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed a new filter
i simply took the old one out and replaced it with the new one. it fit perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Hummelstown, PA
- Parts Used:
- 3204267
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Dryer Would Not Heat
I researched possible causes on line and watched a PartsSelect video on YouTube on how to test. I ended up misreading test results and ordered the High Limit Thermostat but subsequently realized problem was the Terminal Block. No problem, PartsSelect took back the Thermostat (I hadn't installed it) and shipped me the Terminal Block. My dryer was back up and running in less than 7 days from initial analysis to installation of Terminal Block. Instructions that came in confirmation email for installation were perfect and easy to follow. Total cost with new power cord from Home Depot was less than $50 vs a quoted service call of $175+ parts from local electrician.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from Lakewood, OH
- Parts Used:
- 218470300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic water valve sprung a leak through the plastic.
Fast and easy. Started by pulling out refrigerator and unplugging it. Water valve for ice maker was already turned off due to leaking. Disconnected old valve, detached old valve, reattached new valve and reconnected water lines. Bled the lines and turned back on. Make sure temp in freezer stays at recommended temps for ice making.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robet from Hermitage, TN
- Parts Used:
- 218470300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Not getting water to freezer tray.
Turn off water, un-plug refrigerator, dis-connect water, un-screw bracket, remove valve and replace same way...Very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas F. from Whitmire, SC
- Parts Used:
- 134813600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
clothes hanging-up during the drying cycle,leaving marks on the garments.
as on the video. so easy. took longer to clean-up
Was this instruction helpful to you?
Thank you for voting!