EIED55HMB0 Electrolux Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Andy from PASADENA, CA
- Parts Used:
- 134994700
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Digital display alone gone blank without any other dryer operational problem.
Just find & follow a YouTube video instruction on how to replace the control board. Only tool needed was a Phillips head screwdriver. Instruction was clear to follow. Very happy to have purchased the control board at a reasonable price from partselect.com.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ann from WALLA WALLA, WA
- Parts Used:
- 3204267
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
lack of heat
Remove top lid by pushing tab on either side with a putty knife. Disconnect the 2 wire carriages on right. Remove one
phillips head screw on each side that holds front panel to dryer body. Remove front panel by using flat head screwdriver to pry panel from body. Remove thermostat located on bottom right attached to front of motor on a plastic body by removing two phillips head screws. Disconnect wires and place on new part.
phillips head screw on each side that holds front panel to dryer body. Remove front panel by using flat head screwdriver to pry panel from body. Remove thermostat located on bottom right attached to front of motor on a plastic body by removing two phillips head screws. Disconnect wires and place on new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- anthony from JASPER, GA
- Parts Used:
- 134792700
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
heater element went out
followed the instruction on you tube, the part was exact, there was nothing to guess, basically you take the whole front off of the dryer, that in itself is easy (follow instructions), once you get to the element, just plug and play. the worst part was a set screw in the back that did take some patience, but finally did get it in. I am not a mechanic in the least, trust me, if I can do it then anyone can. you will need regular Philips screw driver and one short one, really short, mine is about 2 inches in length, also I used manual one, allot of plastic, so I would not recommend electric drill or electric driver. also a good pair of plyers, but small not large.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Luis from JERSEY CITY, NJ
- Parts Used:
- 134705900, 5308027429
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The original seal was worn out so much so that it kept burning out my motor two Motors two years
I purchase one tube of heat resistant adhesive but I change both seals if you could afford to buy a second to I would recommend you do so the one tube just made it. For instructions on how to prepare the drum for installing new seals I went on YouTube
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yvette from RUTHER GLEN, VA
- Parts Used:
- 134793600
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lint filter unusable due to age
Inserted lint filter into slot.
Replacement is exact match to original filter.
Replacement is exact match to original filter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- margaret from virginia beach, VA
- Parts Used:
- 134793600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed a new filter
i simply took the old one out and replaced it with the new one. it fit perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Hummelstown, PA
- Parts Used:
- 3204267
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Dryer Would Not Heat
I researched possible causes on line and watched a PartsSelect video on YouTube on how to test. I ended up misreading test results and ordered the High Limit Thermostat but subsequently realized problem was the Terminal Block. No problem, PartsSelect took back the Thermostat (I hadn't installed it) and shipped me the Terminal Block. My dryer was back up and running in less than 7 days from initial analysis to installation of Terminal Block. Instructions that came in confirmation email for installation were perfect and easy to follow. Total cost with new power cord from Home Depot was less than $50 vs a quoted service call of $175+ parts from local electrician.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from St Paris, OH
- Parts Used:
- 809160308
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
error code 63 I checked all componenets and wiring for resistance. everything checked ok. noticed charring on the copper contacts in the control board.
removed the top of the cabinet,unplugged wiring from control board, removed screws fastening control board and installed new control board.
Was this instruction helpful to you?
Thank you for voting!