EDG16NS0 Electrolux Dryer - Instructions

Just snap into place

Before this fix which worked beautifully, I tried replacing the flame sensor which did not work. To read that story, search under part number PS459818 (Flame Sensor). Our model is a Westinghouse, so access to the unit is a bit different than the other stories. It's a stacked front-loader sitting on top of a washing machine.

1. Open the little front door (lower left side) by unscrewing the little screw right below it. The door will pivot and slide out vertically.
2. Disconnect the electrical main lead coming from the back of the unit (just in case).
3. Close the gas switch lever on main gas pipe coming from the back on left side (just in case).
2. Remove 2 phillips screws on top of the metal bracket holding the two coils. The screws have to be removed completely along with the bracket. It's easy, they are right in front and there is room for the screwdriver. Use a thin long one instead of one with multiple bits to better align with the screws, which are very close to the coils.
3. The two coils slide right out and are very different so it's easy to keep them straight. Remove electrical connectors before or after removing the coils (I marked the plastic on top with a sharpie to keep them in the right orientation).
4. Drop in the two new coils and reconnect them to the electrical leads.
5. Reconnect main electrical lead from back (match wire colors)
6. Reopen gas lever on gas pipe.
7. Drop in front cover at an angle, tilt vertically and put screw back underneath. Use magnetized screwdriver or a piece of scotch tape to hold the screw or it might fall off the screwdriver.
8. Voila'. It worked.

This website is great. Our dryer is a Westinghouse bought in 1991 (almost 20 years old!) and with this fix it's just like new. In 1994 we used parts bought here to fix our washing machine (Westinghouse LT350RXW1). That machine is now 15 years old and still going!

The conversion kit had everything needed, However the instructions were lacking in description on how to assemble everything, this kit includes the new style burner, igniter, igniter mount, air shutter and propane orifices. A detailed picture would help.
The hot surface igniter was broken in the box, luckily the dryer had the same style igniter already installed. I just had to reposition the original igniter to light properly. No special tools needed. Read the instructions before installing.

There was a lot of screws. And I cleaned everything well. The one part was bad so I replaced them all to make sure it'll last.

First, I read the other posts and got a good idea as to how to do it. I needed to replace the upper felt and guides but decided to go ahead and replace the lower felt and the bearing holder as well. If I had been thinking I would have replaced the belt at the same time but, oh well.

Disconnect the electric plug from the wall.
Pop the top using a medium sized flat head screwdriver.
Disconnect the wiring harness at right front of the unit.
Remove the two screws near the top of the front panel and squeez the retaining clips. You may need a pair of pliers for this but be gentle.
Pull straight up on the front panel to remove it.
To get to the bearing holder, remove the drum by first removing the access panel located at the rear of the dryer and removing the belt from the springloaded plastic pulley. With no tension on the belt simply pull up on the drum while also pulling slightly forward. The drum will pop right out but you will have to apply some pressure. There is no need to remove the three screws at the back of the drum on the inside.
Once the drum is out, remove the two screws holding the bearing holder and remove the assembly being careful not to lose the single ball bearing at the rear of the assembly. Pay attention as to how the assembly goes together.
Scrape off the old felt and glue. Like everyone else, I used a chisle and some GOOP. The old felt came right off with little effort and the GOOP cleaned off the old glue with not too much effort.
Apply the glue that comes with the felt glides according to the instructions on the tube. There's plenty to do both upper and lower felt in that tube. I used some spring clamps to firmly set the upper felt. The glue sets in just a few minutes. The lower felt has a bevelled edge that goes toward the door and fits into a groove on the panel. Once the glue is set you you are ready to put it back together. Like everyone else, I took the time to vacuum out the interior of the dryer and collect the coins and buttons that had accumulated. I found it very easy to reinstall the bearing holder assembly by myself by working from the side of the dryer. I put a dab of grease on the single ball bearing to hold it in place while I reinstalled the assembly. Put some grease in the bearing holder and reinstall the drum, then the front panel and belt. Put the belt back on the tensioner and take care of the couple of lose end and you're done.

This is a "no big deal" repair that looks worse than it is. It took me about 2.5 hours to complete and I was taking my time and just enjoying the fact that I was doing it myself.

1. unplug the dryer, remove the aluminum vent and move it to an area that has a lot of elbow room.
2. remove the top lid with a flat screwdriver. It seems that the top lid was being held by 2 metal clips on each end.
3. on the right hand side removed the 2 wires from the front face of the dryer. this is the switch for the open door sensor. remember which wire goes where.
4. the on the left and right side will be one screw and one metal clip, unscrew and pop the front panel with a flat screwdriver.
5. in front of the drum remove the plastic clip that is used as a guide for the drum to be in place.
6. look in the drum and there is 3 screws that form a triangle shape. remove the screws.
7. remove the belt from the drum. inspect the belt. replace if necessary.
8. lift up and pull out the drum.
9. remove the rear drum assembly and replace it with the new parts.
10. repeat in reverse and your done.
It took me 40 minutes the first time i replaced the rear drum assembly then i forgot to hook the belt up correctly and i unassemble the unit in 5 minutes fix the belt and assemble the unit in 5 more minutes. Now the wife is happy.

The appliance is gas, which made me a little nervous. However, knowing that I had the gas off, I carefully began disassembly. The burner unit is a very simple set up and within a few minutes I had the entire assembly out and noticed that in fact the igniter was broken. I ordered a new one from partselect.com and it was delivered in 2 days! The worst part of the assembly was when I accidentally bumped the new igniter against the underside of the dryer and broke the brand new one!!!..So, I ordered a second igniter and 2 days later installed it in about 30 minutes.

Popped in the new door catch! Tightened the hinge screws( which work loose and allow the door to droop. The reason the catch broke!) Also put red Loctite on the screws in an attempt to keep them from backing out again! Working great so far!!!

Remove top panel with large flat screwdriver and 2 screws in back.Remove bottom panel with 2 screws.Release belt tensioner and remove belt.Remove 3 screws in center of drum inside.Remove drum. Remove rear bearing by pulling up on assembly.Replace all parts in reverse order.

Took apart the dryer, definitely a two person job. Cleaned up a bag full of lint that collected in the dryer (can't believe it didn't start a fire!), removed the old glides and seals, sandpapered off the old adhesive, applied fresh adhesive, attached the glide and seals, waited for the adhesive to dry, reassembled the dryer. Now it's working like a charm!

First I used a pliers to remove the piece of the broken knob that was still attached to the shaft. Then I pushed the new knop onto the shaft until it snapped into place.

It was very, very simple... I just had to find two screws ( that were not included)...no problem...

First I was shocked to receive my part the very next day after ordering. The new timer knob went on as easy as you please. I just matched the flat side of the spindle to the flat shaft of the timer knob.

Replaced rear drum bearing, drum support bearing & drum belt. Still very noisy. Will order new motor & see if that does the trick.

Romoved front from dryer . Then loosened tub , slid belt on , reached in back and put belt on pulley , turned tub till belt went into place and reassembled dryer all with the help of a 3 year old and an8 year old,so in my oppinion it was one of the easiest fixes i've ever done!