CED137SXQ0 Crosley Dryer - Instructions

Very easy, takes 5 minutes of your time. Actually I replaced my stop-start switch and also the timer. First make sure that you unplug the dryer. Using a 1/4" nutdriver unscrew the nuts holding on the back plate, once that is accomplished unscrew the two nuts that holds the switch and take care to unplug the wires on the switch and plug them onto the new switch, bolt the switch back on and replace back plate, and plug in power and presto you are back in business. The most important thing to keep in mind is when you take a wire off the terminal on the bad part that you swap it to the new one and keep doing that till you have them all switched to the new part. I had to pay a service tech $75 to tell me what was wrong with the dryer, ordered part and it came in 2 days. They wanted to charge me $275 to replace the part and it only took me 5 minutes to replace the part.

Took the back off, swapped out the three sensors. Just like the videos showed. Easy as pie!!! Took more time to vacuum the dryer out. , Excellent delivery time and customer service!

take two phillips srews out of lint catch frame. next take a screw driver pry up front top part on dryer.lean back top out of way.take two screws out of top of dryer door. disconnect electrical connection dryer door frame.and pull frame upward and off. you will see roller bracket with end made to put in slott. put it in first slott under belt motor.take belt and pull it through under roller and hook it with screwdriver to motor pulley.by putting the tip of screwdriver on motor pulley with belt on screwdriver and lift up until belt slides on to pulley. make sure you put belt around barrel. before putting belt through roller bracket and on to motor pulley.and use something to put under barrel so it will not get in the way and fall off.

i popped the top off. removed the 2 hex screws in the front upper inner corners. lifted the front panel up about an inch n removed it. pulled the drum out. removed the old broken belt. put the tention roller back into the slots at the bottom panel n base of the motor. mounted the new belt around the motor n thru the tentioner as i placed the drum in position n mounted the belt around the drum. holding the drum in place i replaced the front panel. replaced the hex screws n closed the lid. wah-lah. dryer fixed... thank you parts select

removed 2 screws by the lint collector, lifted top and disconnected the door switch, removed old switch and replaced it with the new one, screwed it back in and reconnected it, closed lid and reattached the screws by the lint collector-done!

I used the instruction vedio on this web site. Instruction from this vedio showed; was very helpful and for a first timer took less than twenty minutes.

My dryer was made so the fan was not removable and I had to reach through a narrow opening in behind the fan housing to put the belt on the motor pulley. The problem I encountered was that I could only use one hand to push against the idler pulley spring while at the same time try to catch the belt and slip it under the idler pulley. It repeatedly slipped off and every time it did the spring and idler pulley would come loose, and I would have to realign the the idler pulley shaft and attach the spring. After the fifth time I left the spring off, pushed the idler pulley shaft all the way in and put scratch a mark on the shaft on the inside of the first hole it enters. Next I drilled 1/16" hole in the shaft where I marked it, installed the spring and idler pulley then slipped a small cotter pin in the hole I drilled. Now if it slips off I only need to reach back and push the idler pulley up and catch the belt.

Pulled drier away from wall six inches. Pulled the plug for the drier power cord out of the wall socket and hooked it up so it would not fall down behind the drier, thereby knocking loose the vent hose. Removed two screws from front of filter housing opening (right of drier top). Lifted up drier top (lid) from the front and secured it in the up position using a stout strap with hooks on both ends. A prop is not a safe way to hold up the lid. Lid is held down only with mildly stubborn friction catches. Door switch was seen looking down along the inside of the drier front on the right side. There was nothing else in that area to cause confusion. Opened drier door and removed two vertical screws that secure the door switch to the front panel of the drier. Lifted the now-free switch and unplugged it from the wire socket. Plugged in replacement switch securely. Replaced the screws securing the new switch to the front panel. Checked that all wiring was back in place and clear of the drier drum. Lowered the drier top. Replaced the screws into the filter housing. Plugged the drier in. Tested the operation of the drier. Checked out spouse's smile. IMPORTANT - Checked that drier vent hose was still firmly in place. Pushed it back in place.

I followed instructions from video -- although the model used in the video was different, the approach was similar. Really the only difficulty was laying on my back (72 years old) and, with one hand and through feel alone (work area was not visible), getting the belt on the drive sprocket and the spring loaded wheel.

Click on the problem and find the possible solutions. Click on the part and watch the installation instructions. Unfortunately, mine was a bad thermostat/fuse that can only be purchased with the High Limit Thermostat which I had already purchased. What you might find helpful is that all thermostats and fuses should show continuity at room temperature when using an Ohm meter. Both purchases arrived within 30 hrs. of shipping. I was impressed. I ended up changing all three thermostats but was still way ahead considering a service call is $140 plus parts. I almost scheduled this service until stumbling onto this site thinking the heater was bad but was much cheaper than the local appliance/repair store. Again, the continuity test showed that the heater was fine and everything already mentioned above could be inspected and changed in less than 10 minutes.

Must remove 2 screws in the lint screen port anchoring the top of the dryer. Next the front panel of the dryer is removed from the machine by pulling up with a putty knife disassembling the clip holding the front in place. 2 more screws are then removed holding front panel of the dryer. The doors sensor switch is then removed freeing the front panel to be removed. At this point after the front panel is off and the top of the dryer lifts in an upwards position and you can now see the tub and the broken belt. The belt has to be reinserted around the tub into the pulley assembly before being pulled onto the motor. The pulley lifts upward towards the tub if it was put on correctly. It has to be placed underneath the pulley in order to have tension put on the belt firming the connection between the tub and motor. To reassemble just reverse what you have taken off in that order. Their is a DYI video which shows the process perfectly. Have a good one !

First, I would like to say how pleased I am with how quickly the part arrived. The repair was very straightforward. I used the video on the PartSelect site to guide me. Removed wires one at a time so that I could immediately put them on the corresponding place on the new part. Took less than 10 minutes.

Thousand dollars for a new dryer or twenty bucks for a new belt. Thank-you parts select. Ordering was easy and the instructions were bang on!