CDE7300RW0 Crosley Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Louis from LOS ANGELES, CA
- Parts Used:
- 5304508449
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Doable with 2 people but it definitely took tiime
Once we got the dryer out of the cramped where we could work on it, the project went a little quicker. I'd recommend using paper plates/bowls, that you label, to hold all the screws for each piece you remove off the back. It doesn't seem like it will be a lot, but we had at least 20-30 screws in 4-5 different sizes. Unlike someone else's install, we had to completely pull the white back panel off, as well as the main back cover, due to one screw holding the air duct from the inside of the dryer compartment (meaning we couldn't reach everything from the back). Getting this screw out was a challenge and seemed like a huge design flaw, but if you can't get to that screw, the old air duct isn't coming out. There are 2 other screws holding the air duct but they're easy to reach once the back panel is off.
Once that was taken out the process was straightforward, we just took our time reattaching everything step-by-step. Now our dryer works like new.
Once that was taken out the process was straightforward, we just took our time reattaching everything step-by-step. Now our dryer works like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Olmsted, IL
- Parts Used:
- 134587700
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Dryer not heating
Very slowly and carefully, you tube videos and schematic very helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Genevieve from NORTH ANDOVER, MA
- Parts Used:
- 131658800
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door catch broke and fell into dryer.
All I had to do was pop in the new door catch. Works perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Hummelstown, PA
- Parts Used:
- 3204267
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Dryer Would Not Heat
I researched possible causes on line and watched a PartsSelect video on YouTube on how to test. I ended up misreading test results and ordered the High Limit Thermostat but subsequently realized problem was the Terminal Block. No problem, PartsSelect took back the Thermostat (I hadn't installed it) and shipped me the Terminal Block. My dryer was back up and running in less than 7 days from initial analysis to installation of Terminal Block. Instructions that came in confirmation email for installation were perfect and easy to follow. Total cost with new power cord from Home Depot was less than $50 vs a quoted service call of $175+ parts from local electrician.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from North Merrick, NY
- Parts Used:
- 134587700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dryer would run for several seconds and then stop. The indicicator lights would then flash.
I seen a post on your website referring to the exact problem I was having. One of your staff recommended changing the control thermistor, which I did following the U-Tube video link you supplied. The repair went well and the dryer now operates perfectly ! Thanks for the accurate and helpful info.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jane from blairsville, GA
- Parts Used:
- 134813601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
The door safety or something needed replaced.
I called a wonderful friend who diagnosed the problem; ordered the repair part; and fixed it!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Otsego, MN
- Parts Used:
- 134587700
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dryer was not drying completly.
I replaced the Control Thermistor (part # PS1149368) by removing the two screws on the bottom of the lower panel below the door. You will see the Control Thermistor just below and to the left of the discharge chute. Remove the two screws holding the Control Thermistor in place. Disconnect the two wire and reconnect to new Control Thermistor. Replace screws in reverse order of above.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond Frattone from Richboro, PA
- Parts Used:
- 131658800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Door would not close because of broken female latch.
Very simple. I removed the broken latch with pliers and snapped in the new one in less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lukas from Pasadena, CA
- Parts Used:
- 5303207102, 131658800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
latch broken
pulled out old catch with old pliers and popped new one, simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bret from Tampa, FL
- Parts Used:
- 131658800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I shut the door too hard, and the old latch fell down into the inside of the dryer.
The new latch easily snapped it into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Mayfield, KY
- Parts Used:
- 131658800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no problem
put door catch in hole
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Adam from Scottsdale, AZ
- Parts Used:
- 137553402
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer gasket keeps coming off
Such an easy repair that I should have done months ago. I knew the gasket was failing but kept fixing the old one until it finally broke apart and couldn't be reused. The new gasket installed within minutes and fit perfectly, not to mention I no longer have to deal with it every time I do the laundry.
Was this instruction helpful to you?
Thank you for voting!