CDG7300RW0 Crosley Dryer - Instructions

There was a small plate and 2 screws holding the 2 coils. I just removed the screws, unplugged the 2 coils, plugged the new ones in and put the dryer back together.

Unplugged the electricity, turned off the gas, then pop open the top of the dryer. Removed the two screws and pulled the front of the dryer off. Removed the two screws that locked down the two m series ignition coils. Put it back together and all things worked great.

Very easy fix on this system as described in other reviews. Simply unplug, lift top, remove two retaining screws on the dryer face, remove face from front of drum. Locate both coils at the lower left corner of the gas valve assembly.

My dryer was heating up very briefly blowing hot air initially then cool. I have a stacking washer/dryer set (2002). I initially turned off the gas valve at the wall, ran the dry for several minutes to clear the gas line, then unplugged the power. I was then able to pop the top using a flathead screw driver, securely prop it open, unhook the wiring harness to the front panel, unscrew the two front panel screws, and remove the entire front without having to unstack the units. From there, you remove the two screws holding the bracket over the coils (2 of them), remove the electrical connectors attached to both coils and replaced them with the new ones. I then replaced all brackets, screws, and such (you'll need to lift the drum when putting the front back on and make sure it is lined up), plugged it back into power and turned on the gas to test the unit which worked perfectly. The 62% of the time seems to be an accurate figure as nothing else had to be done to the unit. Pretty easy stuff...good luck.

After reading other peoples problems i decided it must be the coils after looking at the picture of the part I looked at the dryer to find were the part was. it was right in front behind the inspection cover. so i order the part. it came very fast.these are not the first parts i have purchased from Partselect.the web site is newer now and i am glad because reading other peoples problems help me decide what was wrong with mine.PS Always clean every thing inside the dryer!! 15-20 min job one screw driver! (19 year old unit works fine)thanks to Partselect!!!

Pried the lid up and flipped it back then disconnected the front panel wiring harness and then popped the front panel loose at the top and dropped it down. Disconnected the ignition coils, removed the coil retainer bracket and replaced the coils. Reassembled it in reverse order, performed functional test. Success!

I called a wonderful friend who diagnosed the problem; ordered the repair part; and fixed it!!!

Flame Sensor didn't fix it but, it was easy to replace. Unplug electric. Lift up the top and remove wires from switch and light switch. Remove screws that hold on the front and remove front panel by lifting up and out. Sensor is on the left side of the burner, held on with just one screw. EASY!

I replaced the Control Thermistor (part # PS1149368) by removing the two screws on the bottom of the lower panel below the door. You will see the Control Thermistor just below and to the left of the discharge chute. Remove the two screws holding the Control Thermistor in place. Disconnect the two wire and reconnect to new Control Thermistor. Replace screws in reverse order of above.

Took the coils off and put the new one on thats all

The new latch easily snapped it into place.

Everything I needed to know was already on your website. Prying off the top of the dryer (with a big screwdriver under the front of the top) was the hardest thing, since I was afraid I would break something. Only then can the front be removed (taking out just 2 phillips screws). The rest is easy.

put door catch in hole

Never knew I was handy, but I did it! I was reluctant to spend a couple $100 on a repair visit, so found this site and bought the coils I needed for only $26+tax. It's pretty easy. I just lifted up the top of the dryer with a screw driver, should snap open. Then unscrewed the front panel with two screws from the inside. Then located the old coils on the bottom left. The bracket that holds them is a little difficult to remove as you need to have a small philips screw driver to get the back one. But once I got that off, just unplugged the old ones and put the bracket back, then the panels and it WORKED. The only problem I have is that I didn't take the door switch off properly and now the dryer doesn't stop spinning if I open the door and want to check the clothes. So I may have to get someone in eventually.

pushed screwdriver into the two clips between the top and front to release the connection. took off front. at the bottom front left side, took out screws to access parts that needed to be replaced. put everything back together. dryer works like new. easy.