CDE8500AZW Crosley Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Daniel from Wapakoneta, OH
- Parts Used:
- LA-1044
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Low heat in dryer
I suspected (correctly) that the thermostat was malfunctioning so I ordered the Heating Element Kit. This repair would have taken less than 15 minutes if I would not have dropped one of the sheet metals screws in the back of the dryer when re-installing the heating element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from GORHAM, ME
- Parts Used:
- LA-1006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
drum slide worn out
removed front cover, lifted drum up with a clamp and replaced slides. Replaced front cover
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from FIRTH, NE
- Parts Used:
- WP31001535
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Drive pulley wore out
Item # PS11740721 motor drive pulley. This has a 3/8-24 reverse thread inner bore. Fit my Maytag model MDE508DAYW dryer made by Whirlpool, with drive motor on the lower right below the counterclockwise rotating drum and exhaust blower at the front of the machine. It might work with a number of brands of dryers made by Whirlpool with that configuration. Check the motor shaft thread and the drive belt which is a 5 rib belt 5/16ths inch or 8 mm wide. For Joe Blow the local appliance repair places only quote replacing the motor and pulley as a unit. At $170.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Glendale, AZ
- Parts Used:
- 31001575
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burned out light bulb
removed the lens cover, replaced the bulb and reinstalled the lens cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tina from Selma, NC
- Parts Used:
- 31001096
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
roller wore out and fell off
I just used screw driver to pop of clip put new roller on poped clip back on
Was this instruction helpful to you?
Thank you for voting!
dryer quit rotating and has been off balance
I popped the top off and tipped the dry over . It took 2 to reposition the drum and belt back after taking it out and remving the old wheel and replacing it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- peter from portland, OR
- Parts Used:
- 341241
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Broken belt
Opened up every panel EXCEPT the front, then discovered how easy that is. Replacement belt was a snap to install. I noticed some plastic collar thing on the driveshaft appeared to have melted. Did not appear to be critical part, so I put it together and tested it out. Seems to work fine. I think the collar is there to prevent the belt from potentially slipping off the driveshaft.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from Virginia Beach, VA
- Parts Used:
- WP31001388
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Timer knob broke during move
This repair was ridiculously easy. The timer knob broke during a move I recently made. I googled the item and found your site. I was impressed with how easy it was to navigate the site. I found the part I needed, ordered it and received it within a week. All that was needed was to push the knob onto the shaft and my repair was completed. Thank you PartSelect, for making my experience so easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from callahan, FL
- Parts Used:
- WP53-0771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
dryer not heating
googled"dryer not heating". landed on partsselect.com. checked parts like website said with multimeter. pointed to thermostat. ordered it, replaced it, it works now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Mahwah, NJ
- Parts Used:
- WP53-0918
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Lint Trap - plastic snapped
My part came a day or so after the order was placed. There was really no installation required, but I will definitly make orders from this site again. Thank you very much!
Was this instruction helpful to you?
Thank you for voting!
Dryer stopped running,not heating,drying clothes.
When online& found website... trouble shot for problem per previous posts on PART SELECT.GREAT SITE for problem ifo.I ordered parts,they arrived 2 days later and within 1/2 an hour I had our dryer repaired and working like new!!THANKS!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lou from Weymouth, MA
- Parts Used:
- LA-1053
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Dryer had no power. Internal light was out too.
I followed the "How to" video on your web site. Most importantly, I cleaned the entire filter area which probably caused the problem as your instructions recommended. I will do that annually going forward. I would recommend your service to anyone.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leo from Belle Chasse, LA
- Parts Used:
- WP31001529
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer door seal broken
It was easy. Just removed the old seal and plugged the new one in place. Took less than 3 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mark from santa clara, CA
- Parts Used:
- LA-1053
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Wrench (Adjustable)
Thermal shut off shut off.
Replaced the thermal shut off and the thermistor located on the heating element bracket.
Easy to diagnose and to replace- not totally accessable but not that bad either. Cleaned out lint obstruction causing the problem.
Easy to diagnose and to replace- not totally accessable but not that bad either. Cleaned out lint obstruction causing the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from Guys Mills, PA
- Parts Used:
- 341241
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
The belt needed replaced
Once we realized we needed to take the FRONT off the dryer, not the back all went well. It was an easy fix and the part fix perfectly. Instead of $60 or more for a repairman, we spent less than $20 fixing the dryer.
Was this instruction helpful to you?
Thank you for voting!