CDE20C7 Crosley Dryer - Instructions

First I was told by the maytag repair man that the motor was shot and it would be 467 dollars to repair. Since I didn't have that kind of money I decided to take it apart to see if I could replace the motor myself. Once I had it apart I saw the part that held the motor in place was broken off and the motor was out of place causing it too shut itself off. Once I figured it all out it took about 2 minutes to replace the less than 6 dollar part! Thanks partSelect!!!

Removed power and front panel, removed broken latch, pushed in new latch and replaced the front panel and power. Done

Ordered the leveling bolts, very fast shipping, parts correct as shown. Purchased a condo by the shore, frige had no levelers, they went in smoothly & was done in no time.
Steve

After watching the great install video, I followed his lead and within 20 min had my dryer door fixed. This dryer was bought in 1986 and I really thought I was looking at buying a new dryer. How wonderful that I could fix it for less than $11. Easy to find web site, easy to find part, great instructions and fast delivery!

discovered it was a broken latch. Ordered the latch, only took 2 days to arrive and all I had to do was remove the broken latch and snap in the new one. I saved myself a service call. I'm very happy!!!!!!

I took apart the dryer by unscrewing the top and the front, front comes off by just undoing the two top screws on the inside. I figured it was something to do with the rollers since the noise was ciclycal. The hardest part was to put the drive belt back on. It helps to have a second person for about 5 minutes.

Disconnect power. Removed front panel and lifted top. Removed belt around spring pully and motor assembly. Carefully eased belt around back of drum and gasket. Reverse process.

I watch the video and played it again while I was working.
I am a 54 year young woman and I did it.

I took the back of my dryer off to see if the problem was there. I saw that the belt was broken and laying on the inside of the dryer. Took belt and went on line (Google) my KitchenAid Dryer from it's model number. The website was PartSelect. Found the belt I needed and saw a video on how to replace the belt. I called to order the belt and spoke to Steve, which help me with all my needs. Steve knew just the belt I was looking for and placed my order. The belt arrived a few days later. While I was waiting for the belt to come in, I removed the front of the dryer and get ready for reinstall. It took me about 15 minutes to install the belt and put the front of the dryer back together. I found PartSelect to be very helpful and saved me, maybe $150.00 by not having to call a serviceman to do the easy replacement. Thank you Steve and PartSelect, now I'm number 1 with the wife again.

Pull dryer out from wall about 6 to 8 inches step 1 - romove front/bottom access panel. Step 2 - remove lint trap and remove 2 screws (philips type) that is under lint trap door. Step 3 - push in 2 wood shime in front edge between lid and front panel (angled shims like door shims - a putty knife will work to, just be carful not to scratch finish) step 4 - fold lid upward and back (like on a hinge) step 5 - looking from where the bottom/front acces panel was losten 2 screws - one left one right about 3 turns - 9you can remove them it just makes it easier to reinstall the front panel. Step 6 - find appropriate pot or stacked 2 x 4 pieces - something to hold up the drum when you remove th front cover, and from underneeth support the drum. Step 7 - look thru bottm front access hole - there are 2 springs that come down from the door - and clip onto the frame of the fryer - unclip them and place on the side. Step 8 - remove 2 upper screws that hold front panel on, and remove front panel, if you left the bottom screws attached but loosened you have to lift up on the front panel a bit. Step 9 - looking from the bottom thru where access panel was - you will see motor on right with a additional roller (tensioner) - push upwards on tensioner to relieve pressure on motor and pop off belt (remember where tensioner is and how it clips in to base. Step 10 - work belt off of drum towars front - to remove it all the way you will have to lift up the drum slightly off of the pot or whatever you used for support so the belt can clear. Stem 11 - new belt goes on the same way you took to old one off - plat side away from drum with ribs against drum. Step 12 - again lift up on drum and work belt back on. Step 13 - tricky part is how to get the belt back on the motor - prentend you are threading a needle wht a folded over piece of thread - hold the belt with about a 4" loop with your left hand - hold up on tensioner and feed it back thru and work belt back over end of motor pulley, after front panel is back on with the 4 screws tightened spin the drum and make sure belt is between the 2 lines marked on the drum and remove the pot or whatever u used to prop up the drum. Dont forget to attach the springs for the door assemble all other components in reverse order. And dont forget to take the pot back out

I removed the lint trap then the dryer cover from top and front side. I placed the belt around the dryer drum being sure to put it on the correct side with the grid side against drum. I coiled the belt around the pulley and motor tract. Replaced everything in opposite order in which it was removed.
Video from website was very informative and helpful. I was able to follow along step-by-step to replace the dryer drum belt. I am officially a do-it-your-selfer!!!

The repair was much easier than anticipated. Next time I could do it in less than 30 minuites.

Replaced the axel that holds the rollers as well as the rollers. Just rotate the left one 90 degrees and it slides out.

Probably what took the most time was puting the belt back on. It is old so I was being careful. It took a couple of trys to keep it on the rollers as I moved the drum into position. So easy I am convinced to buy another Maytag.

Wife was impressed so that's worth something!

Took two screws out of the Lint tray on top. remove to bolts from under hood then put new belt on. Always make sure there are no twists in belt when put back on

I watched the video on replacing the belt and it was amazingly as easy as the video described. I had asked my son if he could replace it if I couldn't and I didn't have to ask him. If you are only moderately ept at repairing anything you could do this. I was waiting on it when it finally arrived and in no time I had it replaced and my dryer back working. Being a woman I like it when I can repair something myself and not have to rely on someone else to do it.

The repair was pretty simple.
1. unplug dryer.
2. use a med. flat screw driver with some cloth wrapped around the blade as not to chip the paint surface. From the front of the dryer,
carefully pry open the top surface of the dryer. There are 2 points to lift, about 3" from the right side and 3" from the left side.
3. The top will open like the the hood of a car, lift gently, you might have to move the dryer out if you can (if you are on a flexible service connection).
4. Unclip the push bottom elec. switch.
5. Carefully remove 2 sheet metal screws on the top left and top right (from the inside of the dryer cabinet. These hold the front of the dryer in place. You have to remove the front of the dryer to get the drum out. I can't believe that these 2 flimsy screws hold the dryer together.
6. Pull the front panel off, tipping it forward. More on this later, it's really important!!
7. Remove the drum, it's light weight, but bulky.
8. Now you will see the motor assembly and idle pulley.
9. Follow the belt diagram with the replacement belt package.
10. It gets a little tricky to get the drum back in because there's a bit of spring tension on the drum from the belt.
11. You're ready to re assemble. BUT, the next step is really important.
12. Since you have the front panel off, you can get at the lint trap. Yeah, lint. Ever wonder why your favorite Tee shirt gets thinner and thinner? Well, look in the lint trap. I filled a vacum cleaner bag with the hard packed lint.
13. By the way, you have to remove the 2 torx screws that hold the lint trap assembly.
14. Vacuum the whole exhaust pipe while u are at it.
That's it!