WGR211ES2 Crosley Dryer - Instructions

Removed back panel. Popped off top of dryer, then removed front of dryer. Slid belt onto tumbler, put front cover back on, put top back on and adjusted belt frombottom panel cover.

I know that the knobs on the Gibson dryers break as they are plastic and the back cracks so it won't turn. I have had to get several new ones over the years. I went to Google put in Gibson dryer knob and found it, I had the model number so that helped. I had the part within 24 hrs, awesome service from PartSelect.
Emma W

Took out of package. Used screw driver to pop off old broken handle.
Installed new part in a minute or two. Nothing to it. Was very pleased to get the part and so easy to install.

took apart and replaced parts easy to do but no one in my town can get me parts. thay want 100.00 gust to come out and look at it so found parts online and thats that

Opened the plastic bag, took out the new knob, slid it on and DONE I'm not using pliers anymore!!

The first thing I did was logged onto the internet to search the web for my dryer information. Next, after I found the correct model, the site referred me to the parts section and that is where I determined the problem was the M series ignition coil. I then unplugged the dryer and turned off the gas. I took a screwdriver and popped the top off and cut the wire straps that held the door strips and the light to the front panel. I then unplugged the door switch at the connector - HOWEVER - DO NOT TRY TO REMOVE THE WIRES FROM THE ACTUAL DOOR SWITCH BECAUSE THEY ARE VERY FRAGILE AND CAN EASILY BREAK. Next, I removed the two screws that hold the front panel on. By using a slight bit of pressure, I removed the front panel and was able to locate where the ignition coil switch was. (It was right in front) I then removed the two screws that held the clamp down, as well as the bad coils. The coils easily slid off the post and the new pieces slid back on just as easy. I then replaced the screws and clamps to hold the new pieces in place and replaced the front panel. **NOTE ~ while the front panel is off, it would be a good time to clean out all the built up dirt and lint that has accumulated over the years. Lastly, I re-connected all switches and wires and replaced the top panel. Once I turned the gas back on, everything ran beautifully.

Blower wheel came apart from molded-in nut, was loose, was rubbing on housing wall, and was likelynot moving to much air. I read some troubled stories about separating the wheel nut from the motor shaft so bought a new motor and blower housing and install wall pretty easy. There are videos on the teardown process and does that long and not alot of parts to keep track of either. I have already done the felt drum liner and rear drum ball and belt so if it's older than 15 years and your going to take the dryer apart, replace all these parts and you will about have new dryer at half the cost of new.

replaced rear drum bearing kit. Watched video made it real easy. The only problem was getting the belt back on the pulleys.

Watched video sent to me after I purchased belt on line. Super helpful!

I looked up a YouTube video on my specific model. Found one that said “basic disassembly”. I watched that and had it apart and back together in no time. Very easy to take apart and put new parts back in it. Re-assembled and since the repair no squeaking.

Remove top cover and front and remove drum and install a new bearing kit and new belt.

First I took the drum out of the dryer. This was an easy tear down. I had to remember 2 wires, and a belt assembly ( 2 pullies ). I removed 3 screws inside the drum to release the bearing assembly from the back. Then I went to the dryer chasis and removed the mounting bracket by removing 2 screws. I simply replaced the mounting bracket with the new one. This required having to use a magnet to hold a small ball bearing in place while I worked the rest of the pieces in position.I greased it up and went back to the drum. I replaced the old bearing assembly with the new one. Easy. I took the time to shop-vac the inside of the dryer. There was a lot of loose lint, candy rappers, coins, etc. Finally, I put it back together. Unfortunately, this is the forth (4th) time I've had to do this. It's cheaper than buying a new dryer. Now, I've got to fix the washer.

I removed the cracked knob and attempted to replace with the new knob. Unfortunately my new knob did not fit. The internal diameter of the replacement knob was 2mm too small. I did not want to go through the hassle of returning and requesting another knob. So I just made it work. Thanks

I took the dryer apart to vacuum and check because of the screaching noise. Took drum out and found the bearing in pieces and shaft had rubbed against the brace. I thought as old as my dryer was I would never get a piece to fix it. I got online and found PartSelect.com. I found the part but could not tell if all was included. there was a Phone Number so I called it. I was helped instantly. They acted like it was no big deal to have a dryer that old. I got my part within a week and had my dryer back together. It works like new. Thank you

UNPLUGGED the dryer!!! Search this site they have instructions for many of the tasks they sell parts for... disconnect the vent hose, removed the access panel for the motor & belt (rear) (1/4 nut driver), slipped the belt off the idler pulley and motor pulley, carefully lifted the front edge of the top panel & rotated it back on the hinges, labeled and removed the door interlock wires (2), removed 4 screws securing the top of the front panel (5/16 nut driver) (magnetic is best), removed a yellow guide also attached to the top of the front support (5/16 nut driver), rotated the top of the front panel clear of the drum opening (while supported) and lifted the front panel off the bottom guides, carefully lifted the back of the drum straight up about an inch while supporting the front of the drum, remove the drum from the opening created by removing the front panel (the belt should come out with the drum, removed the rear parts of the new bearing (atteched to teh back of the dryer) 5/16 nut driver... you will need a helper to catch the ball bearing holder on the exterior back of the dryer in the middle, unscrew the drum half of the bearing assembly from inside the drum (3 phillips head screws). I have done this several years ago and you will be amazed at how much dust and lint there is... CLEAN AND VACUUM EVERYWHERE AND THEN ALL THE PLACES YOU MISSED DONT FORGET THE VENT HOSE. Clean all of the old grease from the back of the drum and dryer. Installation is the reverse of removal. Don't forget the new grease and DON"T loose the cute little ball bearing that comes in the new kit. There are lots of sharp metal edges inside so use caution and hopefully you got a new belt since belt replacement requires all of the same steps except for the actual bearing removal.

I can attest to this system only on my model since this is the second bearing I have done.

Sure beats the cost of a new dryer!!! Thanks PARTS SELECT This is the 5th appliance I have repaired for freinds and family with parts purchased from your site.