CDG4000HW1 Crosley Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Cherry from WATERVLIET, NY
- Parts Used:
- 134503600, 5303281153, 131825900
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Very noisy
Replaced rear drum bearing, drum support bearing & drum belt. Still very noisy. Will order new motor & see if that does the trick.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from little Egg Harbour, NJ
- Parts Used:
- 5303281153
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Lound noise inside dryer
1. unplug the dryer, remove the aluminum vent and move it to an area that has a lot of elbow room.
2. remove the top lid with a flat screwdriver. It seems that the top lid was being held by 2 metal clips on each end.
3. on the right hand side removed the 2 wires from the front face of the dryer. this is the switch for the open door sensor. remember which wire goes where.
4. the on the left and right side will be one screw and one metal clip, unscrew and pop the front panel with a flat screwdriver.
5. in front of the drum remove the plastic clip that is used as a guide for the drum to be in place.
6. look in the drum and there is 3 screws that form a triangle shape. remove the screws.
7. remove the belt from the drum. inspect the belt. replace if necessary.
8. lift up and pull out the drum.
9. remove the rear drum assembly and replace it with the new parts.
10. repeat in reverse and your done.
It took me 40 minutes the first time i replaced the rear drum assembly then i forgot to hook the belt up correctly and i unassemble the unit in 5 minutes fix the belt and assemble the unit in 5 more minutes. Now the wife is happy.
2. remove the top lid with a flat screwdriver. It seems that the top lid was being held by 2 metal clips on each end.
3. on the right hand side removed the 2 wires from the front face of the dryer. this is the switch for the open door sensor. remember which wire goes where.
4. the on the left and right side will be one screw and one metal clip, unscrew and pop the front panel with a flat screwdriver.
5. in front of the drum remove the plastic clip that is used as a guide for the drum to be in place.
6. look in the drum and there is 3 screws that form a triangle shape. remove the screws.
7. remove the belt from the drum. inspect the belt. replace if necessary.
8. lift up and pull out the drum.
9. remove the rear drum assembly and replace it with the new parts.
10. repeat in reverse and your done.
It took me 40 minutes the first time i replaced the rear drum assembly then i forgot to hook the belt up correctly and i unassemble the unit in 5 minutes fix the belt and assemble the unit in 5 more minutes. Now the wife is happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from SAN FRANCISCO, CA
- Parts Used:
- 5308027429
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Noisy squeaky dryer
Main problem was the bearing, replaced the belt and felt seal as well
The video instruction was very helpful
Was easy with basic mechanical aptitude
Dryer running great now
All parts from Partselect.com
Have ordered from them before and would order from them again
The video instruction was very helpful
Was easy with basic mechanical aptitude
Dryer running great now
All parts from Partselect.com
Have ordered from them before and would order from them again
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- SHARON from SUMMERVILLE, SC
- Parts Used:
- 5303281153
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set, Wrench set
Dryer making horrible squeaking sound when running
I am a "do-it-yourselfer" despite my husbands opposition. I followed instructions from one of the posts on the site and took apart the dryer. I found the location of the rear bearing and took it out and replaced it with the new one. Easy as that. Made sure the parts looked the same. Made sure I saw how everything went together. I used a magnet to hold the ball bearing in place on the rear mount and taped the metal bracket on the outside of the dryer. Screwed it right in. Reassembled in reverse and works like a charm. To all the women out there who don't think they can do this. It's easy. Give it a try.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Baltimore, MD
- Parts Used:
- 134587700
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
E66 Error code, Door Open. Dryer shuts off on high temperature
Unplugged dryer. Removed top panel (2 screws top back of dryer). Removed control panel ( Unplugged from control board and 2 screws) Removed front panel with door ( Unplugged light from control board, door switch at connector, and 4 screws) Removed Control Thermister from dryer exhaust blower housing located bottom front of dryer ( Unplugged 2 wires and removed 2 screws ) Installed new Control Thermister and replaced all screws and panels in reverse order. Note: Noticed connector for door switch seemed a little loose when connected correctly. Used electrical tape to reinforce connection. Plugged dryer back in and checked operation. Dryer has been used approximately 10 times since repair with no issues.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randall from New Roads, LA
- Parts Used:
- 131825900, 5303281153, 131724301
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
bearing bad and shaft broken
replaced bearing and shaft new belt and everything works just fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- chris from dallas, TX
- Parts Used:
- 131658800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Latch on dryer no longer worked
So easy! I ordered the part on the website. Received it 24 hours later. And popped it in place. Good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from PORTAL, GA
- Parts Used:
- 131658800
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Our door catch got lost inside the dryer after the door was slammed to hard
I took the new door catch out of the packaging and just snapped it in place it was easy peasy and took less time than opening the package
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Geraldine from Lansing, MI
- Parts Used:
- 134412860
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken door handle
removed the two screws that were attached to the old door and put the new door on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lewis from Thornton, CO
- Parts Used:
- 131825900
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
loud squeeling noise
After changing the drum support bearing, and the front felt ring, the noise continued. It turned out to be the tensioner pully. The harmonic vibration travels throughout the dryer box like an instrument so you can't tell where the sound is comming from. Before you do anything, spray a little wd40 between the bushing and the shaft on the belt tenioner pully. If the squeel goes away, you have found your smoking gun.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Batesburg, SC
- Parts Used:
- 5303207102
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
strike broken
popped in one in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Westminster, MD
- Parts Used:
- 134412860
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Handle was broken off
After locating the two screws on the inside of the door, I used a phillips screw driver, in a counter-clockwise motion, to take the screws out. I then removed the remaining pieces of the broken handle and then positioned the new handle in the holes seating it firmly in place. The handle had to be held into place while I negotiated the screws back into the holes turning the screws in a clockwise manner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Lithia, FL
- Parts Used:
- 134412860
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Handle on the washer broke
One new door handle two screws and 5 minutes later it was like new again. Saved a bundle by doing the repair myself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from MONTGOMERY, OH
- Parts Used:
- 134412860
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door handle cracked off
unscrewed old part. screwed on new part. it was a breeze.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from cape may court house, NJ
- Parts Used:
- 134412860
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
door handle on outside cracked at the screws
removed the old handle held in by two screws lined up the new handle and reinstalled screws
Was this instruction helpful to you?
Thank you for voting!