CDE20P7A Crosley Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Would not turn on and no light when door opened
Replaced thermal fuse actually fixed the problem, but also replaced the heating element since you have to remove it to get to the fuse. Just remove the top and parts are accessed in the rear 3 screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Pearl, IL
- Parts Used:
- LA-1008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
loud noise
replaced belt first didnt fix the noise so i replaced rear drum support roller kit and that fixed the noise this was a cheap fix cost me about 70.00 dollars verses a new dryer thank you your website was a big help
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Winter Springs, FL
- Parts Used:
- LA-1044
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
dryer would not start
watched available video on site removed 4 screws all at top of washer. had to replace heater element, thermostat and thermal fuse. very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charlene from Leetonia, OH
- Parts Used:
- WP53-1182
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
the dryer would not run, found the thermal fuse blown
Remove and replace thermal fuse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matt from Norristown, PA
- Parts Used:
- LA-1008
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
couildn't see the belt tensioner and hold it back at the same time
I drilled two holers in the side of the cabinet 1 inch apart. I put them at the same height as the tensioner spring. I put the string through 1 hole and around the tensioner. I pulled the string through the other hole and had my son hold the tensioner back while I reached in and lined up the belt on the tensioner while my son let out the string slowly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lonnie from Soda Springs, ID
- Parts Used:
- 53-1518
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
terminel block melted
replaced the terminal block
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Merrillan, WI
- Parts Used:
- LA-1008
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
left roller support shaft has flat on one side
1.used small flat head screw driver to pop top of dryer. 2.used phillips screw driver to remove front of dryer. 3.disengage dryer belt. 4.take hold of brum and turn and pull out. 5.{left side}take snap ring,washer,roller off then remove support shaft. 6.install new parts, support shaft,roller washer, snap ring. 7,right side has a plastic washer that goes on before roller rest will be as step 5 8.put dryer back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from North Smithfield, RI
- Parts Used:
- LA-1008
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Dryer belt broke
took the dryer apart noticed it needed a belt and rear drum supports. Ordered the parts(they were very helpful on getting the right part . they came in very fast (less than 24 hours). replace the broken parts. The dryer is working great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Todd from San Antonio, TX
- Parts Used:
- LA-1008
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Squeaky wheel
Basically I started off using youtube to see how to install. Two things to be sure you do – one the plastic washer only goes on one side (read the instructions)of the shaft and two the support brackets are not threaded so you need to use the original self-tapping screws. The screws that come with it will not work. Best to use a socket set to install the screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pete from Greensboro, NC
- Parts Used:
- WP53-1182
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Dryer stopped and would not restart while drying load
Disconnected dryer main power supply from wall socket. Opened dryer top,Thermal Fuse is mounted on the Heating Element support bracket on the upper left hand side of the back wall of the dryer. Disconnected wires from damaged Thermal Fuse. Removed hex bolt securing Thermal Fuse Bracket with a nut driver for easier access. Pull up on Thermal Fuse support bracket and remove. When reinstalling Thermal Fuse bracket be sure and line up securing clips with the slots on the Heating Element bracket. Once these are alinged push down until Thermal Fuse Bracket is secure and proceed installing the hex bolt to finish installation. Reconnect both wires and dryer should be ready for operation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jamie from murfreesboro, TN
- Parts Used:
- LA-1044
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
dryer was not heating.
i checked the power cord to be sure it was plugged in properly. i checked the thermal fuse in the front. i checked the thermostat fuse. i checked the heater element circuit and found infinite ohms. i checked kept the front cover up and watched that the heating element never came on. that confirmed my decision to buy the heating element. i installed a new one along with the thermostat that came in the kit. problem solved! my dryer is working again and everyone is happy again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Festus from Boulder, WY
- Parts Used:
- LA-1044
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Was not heating
It wasnt to bad,its way easy for people with small hands its a tight fit for larger hands that was my only problem.After putting the dryer back in service it still did not heat correctly so I pulled the lint catcher out and the vent hose off the back and blew it out with an air compressor my God what a mess it was plugged bad should have had a fire so please look at doing the same with yours if its an older dryer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- maria from charlotte, NC
- Parts Used:
- LA-1044
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
heating element needed replaced
Removed 3 screws and replaced the element and thermostate. No high priced repairman needed.Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from longwood, FL
- Parts Used:
- LA-1044
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
heater coil went out
first I watch the video of the repair on the web site-(and for a guy like me who can not fix this was very very easy.Thank You parts select I will use you in the future. DON W.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lana from Havre, MT
- Parts Used:
- LA-1044
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Dryer Wouldn't Heat
Followed the instructions in the video and it was SO easy! Now my dryer works great!
Was this instruction helpful to you?
Thank you for voting!