CEDC392PQ1 Crosley Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michael from MORGANTOWN, WV
- Parts Used:
- W10828351
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Old lent trap replaced with new...
Popped out the old lent trap & popped in the new one..and walla perfect repair..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from HAYWARD, CA
- Parts Used:
- W10828351
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old filter and cover had rusted retaining clips and rusted out sections
Removed old assemblies manually and replaced with new. Very easy and the parts fit perfectly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Tiburon, CA
- Parts Used:
- 349241T
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
incessantly annoyingly squeaky dryer
Take out 2 philips screws in lint trap holder on top. Use flat screwdriver to pry up front left and right of dryer top near outside edges and tilt up out of the way. Remove 2 push-on AC connectors on door switch and remove plastic clip holding wires to dryer's front top metal edge. Remove (2) 5/16" sheet metal screw on inside top left and right edges to free up front panel. Lift front panel about an inch and it'll then pull off. It helps to have a second person to help hold or remove the drum at this point. It took 3 times for me to guess right on the squeak. First time I replaced the belt, second time I replaced these rollers, third and final time I replaced the idler pulley, the shaft of which had worn completely off so clearly i can't figure out how we didn't see (or hear) it the first two times! Dri-Slide lube helped stop the squeaking the first two times, but it always returned until this time, now I have a thoroughly rebuilt dryer for the next generation! (PS vacuum out the bottom of the dryer while it's open to remove both lint and greasy roller shavings - do this FIRST and you'll have cleaner hands & clothes!)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Rossville, IN
- Parts Used:
- WP3406105
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer continued to run non-stop
Found that when the dryer continued to run after the door was opened that the door switch had gone bad. I unpluged the Dryer, opened the top of the dryer to get access to the switch by lifting top up with fingers and a gentle prying of a flat screwdriver to release spring clips holding it down. I then unplugged the wires from the switch and removed the 2 screws that held the switch in. Then reverse this process when you get your new switch from part select (which we received in 2 days) and the total time to fix it took aprox. 10-15 min. total to do. Easy fix for ANY handy person at home!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maxine from FORT WORTH, TX
- Parts Used:
- W10828351
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lint Filter and Cover Missing
Didn't need a repairman for this project! Ordered the part (seems like on Sunday) and got it really quick (the next Wednesday). Opened the package, placed the part where it was supposed to go and shazam!!!! Fixed it was quick and easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from N. Ferrisburg, VT
- Parts Used:
- W11613302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Gasket was falling off, needed replacement
Removed door gasket that was on the door. Replaced with newer gasket (was a tad bit too big, so it slipped off as well.) Added some electrical tape to hold it on. Works like a charm.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from CATHEDRAL CTY, CA
- Parts Used:
- W10828351
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
broken air filter
I would not ever consider this a repair. The dryer filter cracked because of my wife put it in loosely. The new one just fit right in.
What was so good about the entire process was how quickly I recieved the part. A matter of two days.
What was so good about the entire process was how quickly I recieved the part. A matter of two days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julie from TUSCARORA, NV
- Parts Used:
- W10828351
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Lint filter on dryer had broken apart
Replacement fit perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anita from WILKES BARRE, PA
- Parts Used:
- WP3406105
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The dryer just stopped working. Couldn’t get it to start.
Watched a you tube video that told me exactly how to do it. Saved us from going out and buying a new one. My husband and I were very proud of ourselves because just to get someone to look at it would have cost us $85. The part was only around $25.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from DES PERES, MO
- Parts Used:
- WP3406105
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The friggin thing wouldn't shut off when you opened the door. The switch dealie was just hangin there like a loose tooth.
The videos showed the tech taking the front off the unit but my unit didn't play that game. Instead all I had to do was take the top loose, (don't forget to take the dryer vent screws out first, that was the first beer) then access to the switch was easypeezy. That coupling for the switch assembly was 2 beers long. Anyways, got it all back together and it works like it's suppose to.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from JOLIET, IL
- Parts Used:
- 349241T
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Rear drum rollers were shot.
I followed the instructions on the video and it was simple. The hardest part was vacuuming out 32 years of lint from around the motor and igniter. I was lucky there was never a fire in the dryer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dorise from Donalsonville, GA
- Parts Used:
- 3394652
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Socket set, Wrench (Adjustable)
a broken belt
my hany man did it....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amy from ANNANDALE, MN
- Parts Used:
- W10828351
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken dryer lint trap
Excellent and super easy. Owned the box and snapped the new one in. Ready for laundry again in a matter of minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carmella from THONOTOSASSA, FL
- Parts Used:
- W10828351
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Lint trap was warped and would not stay in the opening.
Easy for a 87 year old.I just snapped the cover to the filter basket and then inserted the whole basket into the
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WILFRED from NORTH HIGHLANDS, CA
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I recieved the kit the next day after ordering. It took about two seconds to do the repair
all that was required was to push the catch into the slot notools needed.
Was this instruction helpful to you?
Thank you for voting!