CDE6505W Crosley Dryer - Instructions

I followed the instructions and it went very well. The only confusing part was the drive belt for the tumbler barrel I just had to visualize the threading arrangement to get it right. Much like a car fan belt.

I removed the dryer front and replaced the door switch.
Next I replaced the drum glide reassembled the dryer.

A friend did the repair for me. Very simple. Saved me a lot of money by getting the parts and fixing the problem. Thanks!

unplug appliance.removed 2 screws @ the rear of dryer top to tip lid back. unplugged the door switch wires.took out 3 philip screws that hold lint screen to inside of drum.removed 2 screws @ dryer front top. lifted dryer front panel off. the drum was now loose. slipped off old belt - replaced with new. set drum back into place. made sure new belt was on motor pulley & behind tensioner pulley arm. replace & reconnect items in reverse order. plug back in & test. after seeing the wear on the plastic tensioner pulley i regret not ordering that part for replacement also.

The video on the web-site was very helpful in showing how to take it apart. First we remove the power plug from the wall outlet. Then we used flat scrapper to push the top two hidden clips to release the Dryer's top. We used the nut driver to unscrew the two screws that held the front panel. We carefully remove the wires that were connected to switch sensor for the door, and the lights. Next step was to unscrew couple more screws that held the front piece from the main fan housing. At the bottom locate the tensioner of the belt. Release it. Remove the dryer drum with the belt. We took the opportunity to clean off the lint that was all over on the bottom of the dryer. We then could reach the bottom left back of the dryer to unscrew the screws that held the heater unit. Before that we unscrew and release the wires for the Thermal fuse and the limit thermostat which are all located on the heating unit. Then we replace with new pieces. Upon removal of the heating unit we noticed the broken heating element. Next was to place the drum back in. We made sure that the drum lined up with the rear support piece then the front. We rotated the drum just to make sure that it was sitting correctly. Then we screwed the front housing unit. Then we put the front panel back on the hooks at the bottom. That help to line up the front panel with the main chasis. We connected all the connectors to the right terminals. Last was to set the top down on to the chasis. We checked that the duct in the rear is not obstucted. Lastly was plugging in the power cord and testing the dryer. It is working again. Thanks to Part Select's video and parts. Total time was just over half an hour.

Used spackle knife to pop clips on top of dryer. Raised lid of dryer to expose belt. Next used nut driver to disassembly screws from front door and then base ( bag them. Labeled bag and marked inside of dryer with corresponding number to match hardware) disassembled dryer door latch switch and marked red + and white no marking. ( Middle connection not used) removed dryer clean out screen and then removed dryer face next removed dryer blower cover no hardware ( just lift upwards see side clips) opened up side of dryer to gain more access (spread apart manually) removed belt and marked where belt was on tumbler postion with permanent marker used 2 car hold down cords to hold drum in place with back of dryer next removed belt from idler (note to make a drawing so that you know how to wrap this around the idler otherwise the belt will appear to be too large. Remember to reconnect spring. Next step was to removed drum rollers. . . This required a retaining ring pliers cost about $15. I replaced the snap retaining rings. This was easy but requires that you pull the drum forward about 4 inches to position. Next replaced belt and reassembled. Project was a success and runs like new. . . . Saved me $129 service call plus $65 parts without maytag mark-up plus additional labor for the job $130. My cost $65 + $15 tool (retaining ring pliers) $80 versus $259 + ( $65 *50%)ark up on parts) $80 versus $356 -- thanks parts select for saving me $276 during the christmas holiday.

After watching the great install video, I followed his lead and within 20 min had my dryer door fixed. This dryer was bought in 1986 and I really thought I was looking at buying a new dryer. How wonderful that I could fix it for less than $11. Easy to find web site, easy to find part, great instructions and fast delivery!

Very simple repair. Remove front panel, door, drum etc. Try to keep everything seperated, screws etc. I put lockjaws on the back to get the nut off the front. Make sure to check the housing for "melted on" blower wheel residue. Easy enough to remove. I checked with my local parts dealer he wanted twice the price and needed to order it (at least a days wait). PartSelect sent the exact same part in a day and a half. Put everything back the same way I removed. Hardest part is the drum and belt. While you have everything apart don't forget to clean the thermastats etc. PartsSelect was quicker and cheaper.

This is a real easy fix to do by yourself. First, I removed three screws on the inside of the dryer. These hold the air duct assembly in place. Second, remove two bolts on the front-bottom part of the bottom panel. Third after panel is removed loosen the two other bolts and remove air duct assembly. Simple as that.

Idler was the noise source. Drum support rollers were failing also. I almost spent $500.00 on a new dryer, glad I replaced the parts instead. Sounds and works like new. Watch the video,its very helpful. Thanks Parts Select. You should advertise your services on TV or radio. I am glad I found you.

removed the bottom panel. then the door. unscrewed the 4 screws, removed duct and replaced. parts came fast and fit just right! no issues at all! I recomend Parts select as an appliance vendor for parts.

My son n law took the fron off the dryer, whilw I looked on the inertnet to locate whatever part we would find to be in need of. He pulled the front panel off and the drum out to dicover it was the bracket and glide. They were easily replaced by popping the bracket out and snapping th new one in then placing the guide on it proper spot.

My son will discribe how he did the repair.
First I opened the top, then I removed the front with a 1/4 inch ratchet and socket. I took the cover off the blower housing with a nut driver. Used the appropriate socket and a 1/2 inch ratchet, and an adjustable wrench to hold the motor shaft and removed the Blower wheel. I replaced the broken Blower Wheel and put all it back together.
Our dryer is now working great and there are no unwanted sounds emanating from within. We are very happy with PartSelects promptness and that we recieved the correct part as ordered. PartSelect website was easy to navigate. We plan if the need arises to do so again in the future.
Thankyou Frank and Rodney

ordered new knob but I had to request a return of the part I received as the arrow on the new know was opposite of what it should be -

No problem