CDE9500AZW Crosley Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dave from Brighton, CO
- Parts Used:
- WPY54414, WP40111201
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Squealing idler pulley
Propped the machine up in the front, removed the front panel, the door assembly, and the front drum support. Use a Sharpie to mark wire positions. This will help during re-assembly. To get the drum out, you first have to remove the belt from the motor pulley. Drum slides right out. You will need snap-ring pliers to remove the pulley from the idler arm. I also replaced the drive belt because it was cheap, and always a good idea to replace it when you are this far into the machine if it is a few years old. Re-assemble in the reverse order of disassembly. An easy fix for the average do-it-yourself person.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Loretta E. from Miamisburg, OH
- Parts Used:
- W10169313
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Button to start dryer
Per instructions I printed off online: took off door, then the front panel. Pulled out the old switch/button, connected the new switch/button, made sure the new button was working; put the panel back on then the door and DONE!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michell from Inglewood, CA
- Parts Used:
- WP503979
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
My heater would not HEAT!
I asked the Gas Co. if they can come out and relight the pilot to my dryer... (which is common for gas dryers) He tested the equipment and told me that the thermostat was the problem. Most places was looking for around $160 for parts and labor. Well, I saved around 130, as I just simply replaced the thermostat. DONE DEAL!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ray from Lehigh Acres, FL
- Parts Used:
- WPW10116735, WP503979
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Dryer would not start
Remove bottom panel from dryer. disconnect wires off of Limit switch. Unscrew 2 screws, remove old switch. Reverse to install. Important, if limit goes bad you need to replace cycling thermostat or chances are the limit will go out again. (Limit on back wall of dryer). The cycling thermostat is right under the lint screen. Remove 3 wires. Remove 2 screws, remove switch. Reverse to install new cycling thermostat. Toatl cost of 2 parts used 16 dollars and change. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Hawley, PA
- Parts Used:
- WPY503978
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
No heat
Removed the lower front cover. Unplugged two wires and removed two screws in element, slid element out, removed two contacts and attached them to th new element, slid element back in place, inserted two screws re-attached two wires.
Very easy!
Very easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marlo from DeKalb, IL
- Parts Used:
- WP37001142
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken lint screen
took one out - put new one in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Averill Park, NY
- Parts Used:
- WP37001298, WP500121
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
heard the sound of loose change in the dryer
removed the front panel and the drum panel cover.replaced the guides and the felt pads and re-assembled.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dianne from CHATHAM, NJ
- Parts Used:
- WP33001621
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic knob cracked so unable to set dryer
Initially I thought let me call so and so but then I thought, "wait, let me google the model and make and I looked up what I thought might be the part. So for $15.00 I fixed my dryer. I was very proud of myself and my husband was happy I saved him money!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from FORT WAYNE, IN
- Parts Used:
- 56000
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Wrench (Adjustable)
Noisy and blower wheel spin without turn motor shaft
Removed lower panel, door assembly, belt and drum.
Removed blower wheel cover.
Used dremmel tool to cut plastic from metal that attaches the blower to the motor shaft.
Used adjustable wrench to keep motor shaft from turning.
Used vise grip to clamp on metal and turned to loosen blower wheel.
Attached new blower and re-assembled.
Removed blower wheel cover.
Used dremmel tool to cut plastic from metal that attaches the blower to the motor shaft.
Used adjustable wrench to keep motor shaft from turning.
Used vise grip to clamp on metal and turned to loosen blower wheel.
Attached new blower and re-assembled.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Ada, OK
- Parts Used:
- 56000, WP40111201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers
will not blow air
I first unpluged the dryer. Then I
Removed two screws and removed bottom cover, Then removed the door assembly.Here I had to unplug the light and door switches. I then removed the four screws that holds the tub mount in place, Then I removed the eight screws that hold the blower cover in place, then removed the blower. replaced blower and reassembled in reverse. I started the dryer and it worked fine.
Removed two screws and removed bottom cover, Then removed the door assembly.Here I had to unplug the light and door switches. I then removed the four screws that holds the tub mount in place, Then I removed the eight screws that hold the blower cover in place, then removed the blower. replaced blower and reassembled in reverse. I started the dryer and it worked fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from ITHACA, NY
- Parts Used:
- WP33001621
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Dryer dial seat broken
reassembled dial skirt with other two parts and pressed them on to timer shaft. Skirt was approximately one half inch too deep for my model. It works fine but has a gap between the skirt and the dryer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from MERRIMAC, MA
- Parts Used:
- WP33001621
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken Timer cover
Took the old one off, put the new one on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- HILDEGARD from NAMPA, ID
- Parts Used:
- WPY503978, WPW10116735, WP40113801
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Dryer wouldnt heat up
A friend did the repair for me. Very simple. Saved me a lot of money by getting the parts and fixing the problem. Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clayton from DODSON, LA
- Parts Used:
- WP33001621, WP22001664, WP22001659
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
timer knob broken.
Removed broken knob and replaced new timer knob it fit perfect, no problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marcia from Hammond, LA
- Parts Used:
- WP37001132
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Cylinder Seal came out
Early in the life of my dryer, the Cylinder Seal came out. For the past two years I put off buying the part. When it came in, I p[opped the top of the dryer, removed the two screws holding on the front panel, and pulled the Cylinder of the back wall of the dryer. I then placed the seal in the right spot, glued it down and reassembled. About Fifteen minutes of work and a cheap part, and now my dryer dries a l;oad of clothes in an hour instead of three.
Was this instruction helpful to you?
Thank you for voting!