CDE20M6 Crosley Dryer - Instructions

I watched an online video about how to replace a dryer belt & followed the directions. Placing the belt around the drum is easy but stringing it thru the pulley is a little difficult because the belt has tension. This takes a little effort but is doable. Dryer runs great now........Be sure to unplug appliance 1st........

Pretty much just followed the video - I'd never opened a dryer before, so I'd watch a step, pause and do it, then run the video a few more minutes, and repeat. These dryers are really extremely simple devices: just a heater, then a motor to spin the drum and run the fan (I think the same motor does both). So you loosen a couple of screws, pry the metal case open, and slip on the new belt. Done! I didn't keep track of time, but I'm psyched to have saved myself a $200 repair call! Standard delivery arrived in less than two days, just like they said it would.

Followed the instructions and the repair went like clockwork, took less than an hour. I spent more time brushing and vacuuming old lint from the innards of the machine than I did doing the actual repair. Finished up $0.78 richer, too, from the change I found inside the machine.

Was a little hard getting at the idler pulley being it was behind the blower assembly, but it was the only draw back.

Shut off power and gas, unscrewed lint vent, raised top on angle with rope, unscrewed and moved door switch, unscrewed and took off front, put new belt around drum, then raised front end of drum with 4 narrow pieces of 1" foam insulation which let me view and install the belt connection to the drive motor shaft, adjusted the level of the drum using the rope holding up the top, removed foam pieces, replaced and rescrewed the front to fit the drum front channel, replaced the door switch, replaced the top and screwed it to the lint vent, returned gas and power, and ran confirmation test.

I followed the posted directions from others, and it was a breeze. They were really helpful. I would just add the step of keeping the drum in place with a block of wood underneath before removing the front. Slip the belt around the drum, reattach the front , and then finish positioning and tensioning the belt once the block is out of the way .

I went to repair the dryer belt only to realize that it was jumping off the pulley(edge was worn away). If you are replacing the belt, make sure your pulley is good before you order your parts. I ended up having to go to lowes and make a pulley!
Works great though.

My 12 year old son and I took off the front of the dryer to see if we could see what was wrong. The belt was snapped and on the floor of the dryer. I ordered the belt from you--it came three days later. That evening, my son held the drum while I laced the belt through the pulley. We cleaned everything up--lots of lint! Put everything back together, plugged it in, turned it on--SUCCESS! We were wildly excited. I am a stay-at-home mom determined to save money any way I can.

well, the hardest part is getting this thing apart - you have to take out the lint trap and remove the two screws from the top. Then I was trying to lift the top off - it's held in place by clips so you have to gently but firmly lift it off from the front end and let it open while still semi attached at the back (like a chest). Detach the electrical wires - they are just clipped in place. Then remove the screws (one on each side) that attach the front panel, and (and this is the hardest part if you don't know how it's attached). You have to SLIGHTLY LIFT the front straight up and then pull it away towards you. I just pulled it off, breaking the little attachers, which I subsequently had to weld back on with a welding compound and leave it overnight to set. the next day was pretty easy though...

The spinning drum is pretty easy to get out and you set it aside. Then I saw the belt pulley sitting there on the bottom of the dryer out of place -- fortunately with the belt there came instructions on how to instal it - READ THOSE INSTRUCTIONS - after that it's cake - put the belt around the center of the drum and feed it through the other parts underneath (this is easier if you tilt the dryer back a bit to get at it better. And you must pull back on that pulley after you have put it in place again - clips into the bottom of the dryer - it's supposed to have a lot of tension on it. Put it all back together and voila!

good luck!

Un pluged and Moved it out from the Wall, Raised the top, found broken belt. ordered belt on line, 2 days belt came in. cleaned all dust and dirt out put greese on berrings for rollers bleu out vent hose with Leef Blower. put top down, pushed back. pluged in and turned on IT WORKS!!!

Unplugged the 220 line, removed lint cover, (2 screws). Lifted top with a screw driver, (2 plastic fasteners) then unplugged a ground line at the front lip to separate the front panel. There was a 50/50 chance here that I would not put the wires back correctly, didn't not make note of the color differences. There was no lower panel, just a single panel on the front, which I first tried to remove like the top, but quickly saw no results, then lifted the panel easily, which I set aside. I rested the drum on a 4x4 piece of wood. I then slipped the new belt over the drum, aligned the bulkhead at the rear, and positioned the belt in the original position, there was a distinct mark showing this. Next I saw the idler pulley lying on it's side, hmm, thought this might take some time, but the illustrated instructions were very accurate, reset the pulley, pushed it toward the motor and doubled the belt around the pulley, it sort of felt right, according to the grooves on the floor panel. I then rotated the drum counter clockwise, then tested. It worked! Became a hero to my wife and found $1.86 in change, woo hoo! Total cost, including shipping under $20., two day delivery, amazing. Thanks.

I googled 'replace dryer belt' and found instructions on the 'Virtual Repair Man' web site. After reading the instructions through twice I began.

First I removed lent filter and removed the two screws that hold the lent body in place. I rotated the top panel up and back and leaned it on the wall; proped up the dryer drum with some scrap wood pieces; rotated the front panel of the machine out enough to slip the new belt, groves down, around the drum; reinstalled the idler pulley under the drum; raised the drum slightly and reattached the front panel. Reattached the top panel and replaced the filter. Did a test run and worked good.

I got a price from Sears for the part and they were asking $45 just for the belt. I saved enough in parts and labor to take my wife out for a real nice dinner. thanks

After using a voltage meter I tracked it to the thermal fuse. In order to get to the fuse you have to remove the heating element. However when I replaced the heating element I didn't check to make sure that the heating wires weren't touching the metal housing it sits in. So when I turned on the dryer I burned out the element and had to purchase another one so a simple repair became much more expensive. Since the thermal fuse is what blew initially I made sure to clean out the vent from the lint trap all the way to the outside vent. It was pretty dirty and probably caused the unit to get too hot and blow the fuse.

-Took top of by prying with screwdriver.
-2 screws and door wire to take off front panel.
-proped drum with 4X4 piece of wood.
-looped belt around drum where the mark for the old belt was.
-looped belt through tensioner and pulled with the screwdriver over the motors drive shaft.
-manually spun drum to make sure everything was right.
-put panels back on and was done.

You cant go wrong with the included directions and belt diagram. this is the first repair I've done of any kind that went flawless.

We took off the front of the dryer and saw how the new belt needed to go on. It took myself, my daughter, and my husband to get the belt in place and the drum aligned. Once that was done, I put the front of the dryer back on, this holds the drum in place. After that, we sealed the back of the drum like the instructions stated, turned it on, and it worked. We were a little concerned with the instructions stating if the drum was not sealed properly it could cause "fire & death". We kept checking the dryer throughout the evening... no fire, so we were very happy to have done this repair ourselves. Thanks. I would not have tryed it myself except for the positive comments on your site when I looked to order the part. They were correct, it was easy to do and saved us a lot of money in repair service. It also showed my 23 year old daughter how easy it is to some things yourself. :)