CDE20R7WC Crosley Dryer - Instructions

I first unplugged the unit, unlatched the top cover, removed the wires for the door switch, then removed the two screws securing the front panel. I "propped open" the top lid with a 2 by 4. I then lifted away the front panel, removed the blower housing screws to expose the blower. Then I removed the snap ring on the blower shaft, the clamp holding the blower wheel in place, and slid the blower wheel off the motor shaft. Reassembly was in the reverse order. Was very easy.

Opened the top by popping the two fasteners holding it down. Did this with a screw driver. Took two screws out of the front holding collector in place and two screws out holding the front to the two other sides. Put front of dryer down on the floor. Removed old collector and used all other existing material from old collector to finish job. Wife could not believe how quick this was. Put back together was a snap too.

My husband and I used a screwdriver to pry open the top of the dryer, then unscrewed the two front corners of it from the inside. Next, we disconnected wires attached to front lid, then pulled the big barrel of the dryer away from the rest of it. We put a new drum roller wheel on the left side and greased the inside perimeter of it. Next, we took off the old cushion set, and stuck on the newer set, and greased drum glide as well. Lastly, we took off the "old" belt, and replaced it with the one we purchased from PartSelect. We forgot how the old one came off the pulley, but after much trial and error, we figured it out in a snap! (this is why this project took us longer than we expected)
In conclusion, this company for parts is wonderful and I have been referring them to all of my friends!

First off, the parts were exactly what I needed and arrived at my front door in less than 48 hours.
The repair was quite easy. 1. access the "guts" by popping the two clipps and open top panel like a car hood.2. remove the high temp doohickie with a nut driver, one screw, two wires.3. Remove the heating element from its mount. 4. remove the high temp fuse doohickie, By popping off its wires and little retaining bracket. 5. do steps (in this order) 5-1 replacing new parts. 6. spend three hours looking for the dryer brush, you know you have somewhere, to clean 5 years of accumulated lint out of the lint trap.7. drive to Ace, by dryer brush. 8. (most important step) clean the lint trap, or be forced to repeat steps 1-5. 9. Pop a cold one and relish the peace and quiet, devoid of spousal nagging to fix the damn dryer. 10. Take down clothesline in backyard.

I just inserted the door catch, which by the way fit in perfectly. Thanks. Took 5 seconds to repair.

Very easy repair. Just needed to remove some screws to access the heating element area. The fuses are (1) just above the elements and (2) to the right side of them (if facing from the front). Alittle loosening with a philips screwdriver, removing blown fuses, replace with new fuses, tighten new fuses in place, replace outer screws and job done. Also made sure to fully clean lint collection area. I had a good amount stuck in there and it restricted air flow which caused the fuses to blow. It took 6 years worth of drying to make it happen.

After disconnecting power, I popped the lid open by grabbing it on the front sides. Swinging the lid completely back and out of the way, I disconnected the wires from the thermostat. Removing a few screws, the thermostat and the heating element were removed. Reverse the steps and that's it. Very easy repair and now the dryer is like new. While opened, I did take advantage and cleaned all of the lint from the exhaust passages.

Removed the top cover, unplugged the wires on the element, removed bolt holding the element in place. Replacement took about Fifteen minutes to complete.

My wife's dryer started squeaking very high pitched, intermittently and then continuously when running. It progressed to a loud shrieking, unbearable throughout the house. Make sure you unplug the dryer. First I replaced the Drum glide and cushion kit. This was easy to do. Pry open the top of the dryer open with a screwdrive or putty knife. Now reach in and remove the retaining screws holding the front panel against the side panels. After releasing the front panel, let it fall forward about 4 inches and then unplug the two wire connected to the door closed sensor. Now carefully slide the thin belt towards the back of the dryer, it will release eventually as it is pulled off the pulley (dont worry, getting it back on is not that hard). Now you can remove the drum. After removing the drum, there are two tan or bluse plastic drum glides that the fron of the drum rests on. They can be worn out along with the cushion beneath them. Replace them with new one. This actually did NOT fix the problem. I put everything back together and....SQUEAK!! Next I undid everything as before and removed the drum. Now I decided to lubricate the rear rollers. First I used a silicone lubricant that again did not fix the problem. I could not find hi-temp lubricant, so I decided to use Axle grease. Bingo...no more squeak. To lubricate the rollers, remove the retaining clip and pull the wheel off. I put an even thin coat on the post they rest on and the inside hole of the wheel. Replace them and remember to put the retaining clip back on. Now replace the belt onto the metal pulley first, with the threaded side of the belt down towards the drive shaft, it should loop around the drive shaft and then you can pull it around the drum, slowly feedingthe drum farther and pulling the belt back along the drom. The smooth side of the belt should be on top of the drum. Now you have to reach back under the drum on the bottom right corner below the lint trap and pull the belt over the tensioner. Sounds harder than it is. Volia...that should fix it. Its been 3 days of non-stop laundry since the repair and no squeak. Next time I will purchase the replacement roller package, but this worked for now. Good luck.

Quick note: I saved over thirty dollars using partselect over the actuall Maytag store parts dept and they still had to order the part to be delivered in 4-5 days. First I pryed the top off of clips in front then removed the screws that hold the element into place, removed the therostat bracket held in by one screw and disconnected wire clips (after labeling the wires) and removed the thermostat from bracket by two screws then disconnected the element wires and slid the old element out. Reversed the process to reinstall the new parts.

used a flat blade screw driver to open top up(like a car hood) then removed two screws that held the front panel on. Two more screws held the lint colector part in place. The only problem that I had was that I had to use Elmers white glue to hold the gasket that ran around the lint colector in place.Just a little dab, not enough to soak it.When I took the part out there was about a volleyball's worth of lint in the fan blower. Ordered the part and 2 or three days later I had it. If I need another part I will be back...

Was told by repairman that the to replace the heating element in my Performa dryer would cost approximately $185.00 (not incl.tax). Ridiculous! Order part for $59.00 and received it a day after it was ordered. Went to work installing heating element. Five minutes later I was finished. Thanks.

First I removed the 2 screws located on front panel securing dust collector in place, then I removed the two screws on the side of the dryer that secure the front panel. I also "popped" the top
of the dryer from the front panel. The front of the panel was then detached from the dryer. I thenpulled the gasket away from the collector, removed the old one and installed the new collector. Part of the kit also contained a new gasket to the exhaust duct, I merely removed the old gasket and installed the new one.. All this was notas hard asit sounds. The diagram from PartsSelect site helped

My son actually did the repair when he was over here and said it was so easy, even "Mom" could've done it! He said all he did was unscrew one little screw, life out the old part, drop the new part into that slot and replace the screw! It's the easiest repair I've ever heard of! Thank you....I will definitely order parts from your company in the future. Fast shipping too!!

Web search to determine probable cause then search to find parts. Parts Select came through with the parts and quickly. Opened the top of the dryer (after disconnect from power-hate the smell of burning flesh) and found the parts that had up and died. Removed two screws for first part then one more and a lot of cursing to remove the other. Reassembled in reverse order, more cursing the tight space. Dryer back in service, wife happy. Only minor blood loss from sharp parts of machine. Success!