CDE6500Q Crosley Dryer - Instructions

I first made sure there was power to dryer. It was ok so I unpluged the dryer from the socket and afer researching on line I was sure it was the thermal fuse. I check continuity on the fuse and it did not have continuity. So I installed a new fuse and high temp thermostat (they come together)
Just lift top of dryer up and back. In the left rear corner is the heating element. On top of the element is the thermostat. On the right side is the fuse it is a round disc with two white wires attached. The thermostat and heating element need to be removed to install fuse (one screw each and lift out of the way ) . Need to check for blocked lint or like I had the white plastic hose had a kink and need replaced with metal lint hose.

1- cleared all the ducts. (They were clogged and this is what caused the fuse to open)
2- Replaced the fuse from the kit
3- The dryer stopped working again after 1/2 hour -the fuse blew-up again
4- Altough the stat (the other part included in the kit) checked OK with the multimeter, it was actually defective and did not regulate the temp.
5- changed both parts included in the kit, the dryer worked normally again.

I followed the "How to" video on your web site. Most importantly, I cleaned the entire filter area which probably caused the problem as your instructions recommended. I will do that annually going forward. I would recommend your service to anyone.

This is the second time that this has happened with my dryer. The first time I replaced the thermostat and fuse, and it worked for a few years. This time I replaced the element and thermostat at first. Still nothing, then got the fuse; and walla just like new. Of course I lost a screw somewhere down at the bottom of the dryer, so there is only one holding the thermostat in place. Also I took off the front and cleaned out the lint traps; both times it was loaded with crap. Probably why it stopped in the first place.

Easy repair and I am not the handyman type. Unplug the unit. Lift the top. Remove 2 wires from temperature sensor and remove single screw to lift out the plate the sensor is mounted to(Easier to change the sensor out this way). Remove 2 wires from heating element and then remove single screw. Lift out heating element and replace with new one. Screw back in and reattach 2 wires. Remove 2 screws on the plate for the temeperature sensor and replace with the new sensor. Once 2 screws are back in the plate holding the sensor, screw back in with single screw and attach 2 wires. I called a tech and they wanted $125 just to look at the unit. When I read other reviews of how easy this repair was, I thought it was worth a try. Definitely saved us a bunch of money and time.

Once we realized we needed to take the FRONT off the dryer, not the back all went well. It was an easy fix and the part fix perfectly. Instead of $60 or more for a repairman, we spent less than $20 fixing the dryer.

Repair went fairly smoothly, except the wiring connection on the purchased timer was incorrect. Luckily I had the old part to match the new timer.

A. Unplug dryer

1. Removed timer adjust knob by pulling straight out.
2. Remove two screws holding the switch to the front panel.
3. Remove two screws on top of the dryer control panel.
4. Grip the control panel on left and right sides.
5. Pull the panel forward.
6. Optional: take pictures of timer and wiring.
7. Survey the electrical connections from the old timer to the machine.
8. Remove one electrical slip connector from the old timer, and place it on the corresponding lug on the replacement timer.
9. Proceed, one at a time, until all connectors are moved to the new timer.

Open the top of the dryer, thermostat can be plainly seen. this one was obviously fried, made it easy to determine cause of problem. remove old thermostat, pins pull off posts, using socket take off nuts (hang on to the nuts), put the new on. Fixed.

Others have shared as well as I can

I watched the video tape

Grown daughter did the repair following instructions on your site........Unplug, take screws out of top by lint filter and with putty knife pry up top panel and lean back. Unplug elec. harness in front corner. A screw on each side of front panel removes that. Get old belt off and then we vaccumed all the lint from under and around drum. Put new belt around drum making sure not twisted and pull pulley as shown to make tight......... would have taken less time but we vaccumed all the lint from under and around the drum. Anyone could do this......

First I unplugged the dryer. Then I removed the screws that hold the contol panel front on. Pulled up the control panel up and forward and layed it on the top of the dryer face down. (After pulling off the knob.) I removed one screw that holds the mounting plate in position. Then I removed another screw that holds the Switch onto the mount plate.

I pulled off the bad switch and put the new one in place. Put the screws back in. I had to cut about 2 inches of burnt wire back and replace the connector.

Hooked up the wires and put the control panel back in place. Put the screws in, plugged in the dryer and we are back in business.

I first unplugged the dryer. I had to move the dryer forward a little. Then I used a screwdriver to pry up the top of the dryer from the front. I positioned the top all the way back until it rested on the front of the cabinet. Make sure it's far enough back so it doesn't accidentally close on you while you are working on it. I located the high limit thermostat right above the heating coils. I unplugged the two wires going to it. I used a nut driver to remove the screw that was holding it to a bracket. I then I removed the two screws that held it to another bracket. I installed the new thermostat to the bracket and then reinstalled it to the bracket above the coils. I plugged the two wires back in and closed the lid. Make sure the dryer vent is still attached if you had to move it. The dryer works fine now and doesn't overheat.

Received the replacement filter which was an exact duplicate of the 22 year old filter. Took the old one out; slid the new one in and got ready for another 22 years of use. At 86 years of age I probably won't be around to see the new filter wear out. The dryer has already outlasted the place where I purchased it - Montgomery Wards! They just don't make stuff to last like this anymore.

Looked up dryer by serial number on the internet. Watched the video on the website very easy installation. Ordered the part it came in within 2 days. Opened the top of the dryer with a 10 in one tool (like a putty knife). Took out the out defective parts by unscrewing the thermostat took wires off the old part and put them on the new part not to confuse wires. Did the same with the heater element installed the new parts. Very simple. If I had to call a repair person it would have cost 3 times as much as the part alone.