CDE20P6WC Crosley Dryer - Instructions

Unplugged, loosened front cover, disconnected two wires from door open indicator, removed front cover with screw driver. Removed air flow cover with screw driver. Used pliers and retaining ring pliers to remove old blower wheel, my husband calls it a "squirrel cage". Installed new blower wheel and reassembled. It was all easy to see and get to. Thanks for having the right part. Sue.

Took off top and front. Removed belt and pulled drum straight out. Unclipped the rollers. And noticed the rod that holds the roller was worn out badly. Good thing I bought the kit. Because it came with everything needed and was cheaper then buying the rollers seperate. Only hard part was putting the new mounting on for the rod. They are not predrilled. So does take some force. Put everything back togetther and dryer is working like new. fyi you can also clean out your air duct of lint buildup when doing this project. Had a repair man come over 2x in past year and each time he would replace the roller and charge me $150 each time. I spent $300 on that bozo. When i could have ordered the parts myself for a fraction of the cost. This was well worth and easy to do.

I opted to remove front, top and back panels. This is best done with dryer laying on it's back so drum remains in position. Hold panels and pieces in place with masking tape (2") You should block up the dryer so you don't damage the gas pipe. I opted to total shop vac out the piece and lubricate the rollers and tension pulley. I made more in change than the belt cost!

Overall an easy repair. Belt came with diagram for easy threading the belt.

Lifted hood ,and took two screws and tilted the front back and remove the door switch , and took front off ,use little socket set, took cover off fan housing took pliers removed clamp on fan , remove key way on end ,slid fan off and put new one on and reverse the way if came off.

First I disconnected power to dryer. Next step was to lift top of cabinet and support upright. Then I removed door switch and 2 screws that hold front panel on and set front panel aside. Next was to reach under drum by belt tightener and remove drum drive belt from tightener and pulley of drive motor. Then slowly remove drum from cabinet . Once removed, I could remove old glides that were worn out and install the new ones. Before putting everything back together, I gave the cabinet a thorough vacuuming to remove all lint built up inside, checked electrical connections on heating unit and oiled back drum support rollers and belt idler roller. Next just reassembled everything in reverse order as was disassembled. Plugged cord back in and tested unit to make sure everything sounded good before drying any clothes.

removed screws on back plare and replaced heater element. Thank you very much foe your quick delivery of the part I ordered. I was reall;y schocked to see how fast the part arrived. I will recommend your site to anyone who needs parts like I did,.
Thany you Very Much,
Alan Brooks

I (1)unplugged the unit from the power source. (2)popped the top loose at the front corners with a screwdriver. (3)removed the single 1/4 inch hexhead screw holding the thermal limiter mount from the top of the heating element box with a 1/4 inch nutdriver. (4)removed the two wires connected to the limiter. (5)removed the two 1/4 inch hexhead screws that mount the limiter to the holder. (6)replaced the old limiter with the new one. (7)replaced the two limiter holding screws. (8)replaced the wires on the same terminals as they were removed from. (9)removed the screw holding the heating element in the box. (10)removed the element from the box by moving it to the rear slightly, lifting it up on the side the mounting screw is on and withdrawing the holding tab on the other side from the hole it passes through. (11)removed the thermal fuse holder by pulling upward on the thermal fuse mount until the thermal fuse and mount released and lifted them out of the side of the element box together. (12)removed the wires from the thermal fuse. [[>note< wires are threaded through thermal fuse mount]] (13)reconnected wires to themal fuse. (14)there are no bolts holding the fuse to it's mount, so I used a piece of masking tape to hold the fuse in place temporarily while aligning it with the mounting holes in the side of the element box, and snapped the mount, and the fuse into place with a downward motion while holding pressure on the mount in the direction of the box then removed the tape. (15)replaced the heating element into the box by threading the mounting tab into the hole it passes through while holding the element slightly to the rear of the box and lowering into place. (16)replaced the screw that holds the heating element in the box with the 1/4 inch nutdriver. (17)located the thermal limiter and its mount on the tab over the top of the heating element box, and replaced the mounting screw with the 1/4 inch nutdriver. (18)made sure all wires were secured in the clearance clips provided lowered the top and snapped it into place with equal downward pressure on the front of the top. (19)plugged in the power cord. (20)Tested machine (FIN)

No Repair, just replacement. Went perfect.

removed front cover, lifted drum up with a clamp and replaced slides. Replaced front cover

When online& found website... trouble shot for problem per previous posts on PART SELECT.GREAT SITE for problem ifo.I ordered parts,they arrived 2 days later and within 1/2 an hour I had our dryer repaired and working like new!!THANKS!!!

Finally got tired to greasing the wheels only to have to do it again so I sprung for new wheels and shafts. Popped the top open, removed the drum, installed the two new shafts with supplied screws then attached the wheels. Figured I'd change out the original belt while I was at it even though the old one still looked good. It's nice and quiet again, plus it give me a chance to clean it out.

Had to disassemble most of the dryer including pulling dryer drum in order to get to drum support rollers. Not a real difficult repair, just time consumming because of amount of parts needing to be removed inorder to get to rollers.

Very simple-remove 3 screws that hold the Control Panel on, remove the two connectors and replace with new part in reverse order. Unfortunately, this did not fix the problem. Will be ordering complete timer assembly.

Opened up every panel EXCEPT the front, then discovered how easy that is. Replacement belt was a snap to install. I noticed some plastic collar thing on the driveshaft appeared to have melted. Did not appear to be critical part, so I put it together and tested it out. Seems to work fine. I think the collar is there to prevent the belt from potentially slipping off the driveshaft.

My part came a day or so after the order was placed. There was really no installation required, but I will definitly make orders from this site again. Thank you very much!