CDE20R7H Crosley Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Vivian from Dix, IL
- Parts Used:
- LA-1044
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Dryer running, but no heat.
Unplug the dryer. Take a large flat head screwdriver and pop the hood loose from the retaining brackets on the front of the dryer and raise.Next, unhook the wiring from the thermostat and heating element with needle nosed pliers located in the back left corner. Use a 5mm socket to remove the thermostat bracket and the heating element bracket.Remove faulty part and replace. Replace heating element and tighten.Replace thermostat on the retaining bracket and tighten. Plug your wires back in and close the hood.Plug Dryer back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steve from Raleigh, NC
- Parts Used:
- LA-1044
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
heater coil broken and shorted out against wall.
just like the training video showed, and was very happy at how it came fast, installed easy and back in the drying business.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- scott from bend, OR
- Parts Used:
- LA-1044
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Dryer stopped drying cloths out of the blue. Everything work fine but no heat.
I watched a part select youtube video on possible fixes for the problem I was having. Ten minutes and two videos later I had the part out and identified as the problem. I ordered the part ($42.00) which arrived four days later. Spent ten minutes replacing it in machine, turned dryer on and went right back to performing the way it has for the last 12 years. Easiest thing I did all day. Saved me $400 bucks too. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Northfield, MN
- Parts Used:
- LA-1044
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
looked at heating element saw wire was broke
Took less than five minutes to fix a couple screws and take some wires off and pull it right out. Called local apliance store if they had part wanted more than partselect with next day shipping
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip from Lamar, MS
- Parts Used:
- LA-1044
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Element was bad and wasn't heating
I watched your video and it was exactly like you guys said. You truly have a great site and I will tell all my friends about it. Great service, can't say enough about how pleased I am with your site and service. Saved me a lot of money.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Pearl, IL
- Parts Used:
- LA-1008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
loud noise
replaced belt first didnt fix the noise so i replaced rear drum support roller kit and that fixed the noise this was a cheap fix cost me about 70.00 dollars verses a new dryer thank you your website was a big help
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- maria from Kissimmee, FL
- Parts Used:
- LA-1044
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
unit was working but not heating
After lifting up hood, my husband removed old part and installed new part 1, 2, 3. Took about 20 mins.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rodney from West fork, AR
- Parts Used:
- LA-1044
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Dryer not warming
Found the heating element under top of dryer towards the back and replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nyssa from Severna Park, MD
- Parts Used:
- LA-1044
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Drying not heating/drying clothes
I unclipped the top of the dryer for access to the heating coils. I unscrewed the bracket holding the high limit thermostat (the heating element was directly below the high limit thermostat). I removed one screw holding the heating element in place, and then removed the faulty heating element. I checked the old heating element and the old high limit thermostat with a multimeter to confirm that they were faulty - both the heating coil and the HL thermostat had continuity but the coils looked like they needed to be replaced (not rusty, but dingy). I installed the new heating element and the new HL thermostat, closed the top of the dryer and ran the dryer - it worked :) Thanks partselect.com!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- maria from charlotte, NC
- Parts Used:
- LA-1044
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
heating element needed replaced
Removed 3 screws and replaced the element and thermostate. No high priced repairman needed.Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from longwood, FL
- Parts Used:
- LA-1044
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
heater coil went out
first I watch the video of the repair on the web site-(and for a guy like me who can not fix this was very very easy.Thank You parts select I will use you in the future. DON W.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Todd from San Antonio, TX
- Parts Used:
- LA-1008
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Squeaky wheel
Basically I started off using youtube to see how to install. Two things to be sure you do – one the plastic washer only goes on one side (read the instructions)of the shaft and two the support brackets are not threaded so you need to use the original self-tapping screws. The screws that come with it will not work. Best to use a socket set to install the screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pete from Greensboro, NC
- Parts Used:
- WP53-1182
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Dryer stopped and would not restart while drying load
Disconnected dryer main power supply from wall socket. Opened dryer top,Thermal Fuse is mounted on the Heating Element support bracket on the upper left hand side of the back wall of the dryer. Disconnected wires from damaged Thermal Fuse. Removed hex bolt securing Thermal Fuse Bracket with a nut driver for easier access. Pull up on Thermal Fuse support bracket and remove. When reinstalling Thermal Fuse bracket be sure and line up securing clips with the slots on the Heating Element bracket. Once these are alinged push down until Thermal Fuse Bracket is secure and proceed installing the hex bolt to finish installation. Reconnect both wires and dryer should be ready for operation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jamie from murfreesboro, TN
- Parts Used:
- LA-1044
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
dryer was not heating.
i checked the power cord to be sure it was plugged in properly. i checked the thermal fuse in the front. i checked the thermostat fuse. i checked the heater element circuit and found infinite ohms. i checked kept the front cover up and watched that the heating element never came on. that confirmed my decision to buy the heating element. i installed a new one along with the thermostat that came in the kit. problem solved! my dryer is working again and everyone is happy again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charlene from Leetonia, OH
- Parts Used:
- WP53-1182
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
the dryer would not run, found the thermal fuse blown
Remove and replace thermal fuse.
Was this instruction helpful to you?
Thank you for voting!