NDE5800AZW Amana Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Thomas from Summerville, SC
- Parts Used:
- 37001141
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Air duct assembly broken.
I used a large flat head screwdriver to lift top up, then located 2 screws in the top right and left hand side to remove front. Remove the three Phillip Head Screws that holds the assy in place slide out. Mine had 2 metal pieces with wires. I simply unplugged and took metal pieces and installed in the new assy. Remove excess lint put front back on lowered lid and done! 15-20 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Averill Park, NY
- Parts Used:
- WP37001298, WP500121
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
heard the sound of loose change in the dryer
removed the front panel and the drum panel cover.replaced the guides and the felt pads and re-assembled.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from westfield, NJ
- Parts Used:
- 37001086
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
lint filter was in disrepair totally cracked in half ,unuseable
remove old intstall new lint screen 10 seconds. your product was shipped fast!!!!!!!!!!!! i thought i would have to search this item out for days before a reinstallation was made. thanks for your fast professional service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michell from Inglewood, CA
- Parts Used:
- WP503979
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
My heater would not HEAT!
I asked the Gas Co. if they can come out and relight the pilot to my dryer... (which is common for gas dryers) He tested the equipment and told me that the thermostat was the problem. Most places was looking for around $160 for parts and labor. Well, I saved around 130, as I just simply replaced the thermostat. DONE DEAL!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Loretta E. from Miamisburg, OH
- Parts Used:
- W10169313
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Button to start dryer
Per instructions I printed off online: took off door, then the front panel. Pulled out the old switch/button, connected the new switch/button, made sure the new button was working; put the panel back on then the door and DONE!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Hawley, PA
- Parts Used:
- WPY503978
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
No heat
Removed the lower front cover. Unplugged two wires and removed two screws in element, slid element out, removed two contacts and attached them to th new element, slid element back in place, inserted two screws re-attached two wires.
Very easy!
Very easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from Smyrna, TN
- Parts Used:
- 37001086
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The OEM lint filter was cracked and the felt seal was coming loose.
Of course the lint filter is removed and cleaned every load, so I simpy removed the ld one and inserted the new one. No "installation" as such was required, we simply started using the new filter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ray from Lehigh Acres, FL
- Parts Used:
- WPW10116735, WP503979
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Dryer would not start
Remove bottom panel from dryer. disconnect wires off of Limit switch. Unscrew 2 screws, remove old switch. Reverse to install. Important, if limit goes bad you need to replace cycling thermostat or chances are the limit will go out again. (Limit on back wall of dryer). The cycling thermostat is right under the lint screen. Remove 3 wires. Remove 2 screws, remove switch. Reverse to install new cycling thermostat. Toatl cost of 2 parts used 16 dollars and change. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KEN from CLIFTON, TX
- Parts Used:
- 37001070
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Dryer stop signal noise(BRRRRRTTTTTT) would not quit! Had to open door to stop the noise.
Removed back cover of console,using screwdriver and nut driver. Removed old switch by squeezing the end tabs and pulling switch out. Removed wires on switch with pliers. Placed wires on new switch using pliers. Snapped new switch back in place. Replaced back cover to console with screwdriver and nut driver.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scot from Apopka, FL
- Parts Used:
- 37001070
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer would start when pushing start button
Removed the control panel disconnect the wires on the bad part and replaced with new. Extremely quick and easy less than 10 minutes. Part ordered on line and received within one day.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marcia from Hammond, LA
- Parts Used:
- WP37001132
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Cylinder Seal came out
Early in the life of my dryer, the Cylinder Seal came out. For the past two years I put off buying the part. When it came in, I p[opped the top of the dryer, removed the two screws holding on the front panel, and pulled the Cylinder of the back wall of the dryer. I then placed the seal in the right spot, glued it down and reassembled. About Fifteen minutes of work and a cheap part, and now my dryer dries a l;oad of clothes in an hour instead of three.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amy from Petaluma, CA
- Parts Used:
- 37001141
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Vent filter was broken, and lots of lint was passing through to vent line
Removed the two nuts at the bottom of the dryer front to be able to move the front piece. Removed three screws holding the vent assembly in place. Removed vent assembly, replaced with new part and replaced screws and nuts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lonnie from mebane, NC
- Parts Used:
- WP37001287
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
was making a loud noies
unpluged the dryer,and removed the top.
took the front of the dryer off,release the belt and removed the drum.
unbolted the idler lever.
then I put it back together.
the bolt that holds the idler lever will be a little hard to replace for some.
took the front of the dryer off,release the belt and removed the drum.
unbolted the idler lever.
then I put it back together.
the bolt that holds the idler lever will be a little hard to replace for some.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ronald from murfreesboro, TN
- Parts Used:
- WPW10116735, 61927, WP40113801
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Dryer was not heating
I just took the bottom front panel off and the parts I needed to rplace where in the back and very easy to get to . I decided to replace all 3 while I was in there. The parts were not to high, so that is why I did that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Josh from Schulenburg, TX
- Parts Used:
- 61927
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Dryer had no heat.
I took off two screws on the front panel and removed it. I then located the old element inside at the back, left side of the dryer. I removed the two screws holding it in and then transfered the wires to the new element. My dryer works better than it ever did before. Thanks,
Was this instruction helpful to you?
Thank you for voting!