TEA600 (P77041-3W) Amana Dryer - Instructions

After 20+ years of service, the plastic part that holds the dryer door closed, broke. I orderd the replacement part on a Monday and received it on Wednesday!
By applying constant pressure with my thumb, the replacement part 'snapped' into place - all of 4 seconds.
Fast delivery of parts and fast instal, made for a great day.

Repair part just snapped into place. It took longer to open the bag then do the repair. I thought it was going to be difficult to find a part for this dryer but partselect had the right part.
Thanks

To remove and install the new parts, I followed the video instruction at whirlpool.com. Then removed the old knobs and put the new ones in. The new one created a rough contact and needed a little lithium grease to make a smooth insertion to prevent the friction from damaging the new part. It was an easy fix and took about ten minutes. Good luck in your repairs!

I took the two screws out of the end of the door and the door handle off. Then able to part the interior of the door enough to replace the latch. The video was really great.

Replaced the Latch

I used a screwdriver to pry out the broken door latch and inserted the new one in the same slot. Perfect fit. The picture of the part in the order page was a big help to identify the correct part.

unscrew the screws at bottom front of dryer, lift outward, upward, the bottom of the front of the dryer. As the dryer front tilts outward/upward from the bottom, the area where its hinged at the top of the front will disengage from the main frame of the dryer and the face of the front of the dryer comes off. remove the old door latch by manipulating the plastic body of the latch (wiggle, twist pinch . . .) until, from the back, you can push the old latch forward through the front of the front of the dryer. At this point, you can put the new door latch back in from the front and push it in to place.

The dryer door on my mom's Maytag SG1000 (washer/dryer stacked unit) wouldn't stay closed; the latch had finally broken. The replacement kit includes both the female latch and the male striker. I replaced both even though the old striker was still good. The old parts were easily pried out and removed with a small flat-blade screwdriver. But what the PartSelect website, and the other "repair stories" found here, fail to mention is that the male striker is held in place with a small metal "door strike retainer" plate that falls down into the door as soon as you pry off the striker. You will need a small Phillips screwdriver to take the door apart and retrieve the plate. After snapping the new striker into the plate the door can be reassembled -- a simple job that only takes a couple of minutes.

It was so easy to repair that my wife did it. She used a screw driver to pop out the old, worn plastic part that the door latch goes into and snapped in the new part and it was all done. So nice to be able to fix it yourself!

Took 2 screws out of the bottom of the dryer so the front face plate came off. This allowed access to the door latch catch, which was easy to pull out with pliers. Pushed in new latch catch until it "popped" into place. Easy, easy, easy!

To start the repair, I removed the two front panels. Disconnecting the wiring to door and light. Next removing dryer drum and drive belt[ allows access to belt tensioner] replace tensioner roller, then reassemble. Dryer works fine

clothes drier didn't work, tore the drier apart, found problem went looking for the part locally, didn't find it, got mad, went on line, found Parts Select, ordered part, part under $20.00 delivered, part delivered, put everything back together , can dry clothes again, didn't have to find $350.00 to go buy a new drier. Merry Christmas!

Disconnect the dryer from the electrical source. Using a nut driver, first remove the 2 screws of the lower panel and release the panel. Next remove 4 screws of the door panel and then remove the electrical connections to the door (6 wires). Remember to mark the wires prior to removing so you will remember were it plugs back in on reassembly. Remove the door panel. Then remove the 2 screws holding the top of the dryer and tilt the top open about 90 degrees to access the tumbler. Remove the belt by sliding off the tumbler. Remove the tumbler. You will then access the pulley. Using a pair of pliers, remove the retaining ring by pulling upwards. Then remove the washer and the pulley. Replace the parts with the new pulley, washer and retaining ring. This time would be a good time to replace the belt too. Thread the belt through the pulley and over the tumbler. Place the top back and screw in place. Reassemble the door wiring and reattach the door with the 4 screws. Reassemble the lower panel and plug the dryer back into the outlet and test. There should be no more noise if the noise is coming from the pulley and loose belt.

The instructions that accompanied the part was extremely helpful. I removed two screws, lifted off the front panel, used the pliers to remove the old latch, pushed the new latch into the hole. I then replaced the panel (The part that is attached to the door was not broken). I tightened the two screws and the job was complete. I saved a very expensive service call. :)

used one nut driver, basically took the whole machine apart. took snap ring off the idler shaft, replaced pulley, and put it back together. simple job.