NEC3120FW0 Amana Dryer - Instructions

My husband is the one who fixed the door. He said he just popped it into place and was done in just a couple of seconds! The best part though was the quick service we received. . . I ordered the part around 10:30 in the morning, and it was at my front door by 5pm the next day!!! What great service!!!! We will definitely do business again with partselect. Com if we ever need more parts.

The door catch kit is soo easy. They give you instructions on which one to use depending on your dryer and it fit perfectly into the door. This was great especially since it was so inexpensive! My husband thought we would have to replace the door.

Simply installed the piece and I was done. Took 10 seconds.

All I had to do was get the model number off of the dryer and plug that information in online and within a couple of days the part arrived. It was great! There were directions that came with the part that explained how to replace the old latch with the new one.

I remember in the "olden days" when I would of had to call a repair guy out and paid a lot more than the $12.00 I did to replace the part myself. And, the only reason it was $12.00 dollars instead of $5-6 was because I had it shipped overnight.

Awesome!

Simply put it in the exhaust hole.

Removed old catch and strike with screwdriver and needle nose pliers. Installed new parts. My old catch did not have comparible numbers so I just used the yellow one. Worked fine.

very smooth with your video instruction help

Repair was not successful

Lifted top of dryer using putty knife. Took front panel off using socket wrench. Slipped drum belt off an took drum out. Vacuumed out entire interior. Replaced rollers an clips and reassembled!! Saved $100!!! Thank you!!

My dryer knobs ended up not only the problem but when i went to use my dryer the heating element wrnt out.... So i need to return your knobs and get my money back please thankyou however i need the correct forms to send them back and i have the original wrapping

I started trying to locate the noise. I started to remove screws in the rear plate. Removed the rear plate. Couldn't find the noise. Had to remove the top cover and operational controls. Couldn't locate the noise. I figured it was a bearing that went bad somewhere, but I coulnt find it. During the search for these drum rollers I was able to thouroughly clean out old debris and lint caught in the machine for years. Finally I located the bottom front cover, took it off, and located the problem.

At this point I went online, located the part with these guys, ordered it and got it delivered in like 2 days. Pretty quick.

I then went back and replaced the both drum rollers in like 1 hour.

Dryer works and sounds great now.

Removed (2) Philips screws from the lint filter at the top of the dryer. Used a standard screwdriver to pry open the top of the dryer (it hinges back toward the wall). On the inside of the front panel removed a bolt with a socket on the right and left side. Disconnected two wires from the door safety switch (Make sure to unplug the unit first). Lift up on front panel and remove it from the slide connectors at the bottom on right and left sides. Under the drum on the right side pull drive belt slack towards motor and slip off of the pulley. The drum should come out freely. Both rollers are visible remove the triangle clips and the rollers will come off. On lower roller support use needle nose pliers to remove the washer clip that holds the vertical support arm. Reverse this procedure to assemble the dryer again. There is an excellent video that is supplied online. Watch it first , it was very helpful to me.

Raised the top of the dryer and removed the front panel. Then removed the drum to gain access to the drum support rollers. Used the the flat screwdriver to remove the retaining clips holding the wheel in place. Slid the new wheels in place and popped the clip back on. Slid the drum in and put the front back on. The installation video online was extremely helpful.

Replaced drum support rollers but did not fix problem. Motor was fried! Replaced with used motor. NOTE. Make certain you install motor in the right position or you will find the drum sitting on motor. The guide must be in the 4 o.clock position and then placed in bottom groove for proper alignment of motor to drum. Job was amazingly easy and online instructions were super helpful.

Top up, front off. Drew a picture of how the belt was positioned. Removed the belt and drum. Removed a heat plate to access the lower wheel. Replaced it and then replaced the upper right wheel. Was a little concerned the white triangular washers would break going on to the shafts but it turned out there much stronger that I thought. Cleaned out the bottom and found a lot of coins. Put it back together and now it sounds like a new dryer. Use gloves, some parts inside are very sharp.