NED4655EW1 Amana Dryer - Instructions

We pulled the back off the dryer and we weren't sure where the problem was exactly. So we pulled off the heating element and the thermostat. The heating element seemed to be burnt out, so we ordered that and the thermostat. We got the parts very quickly, so we put them in and found that the dryer still didn't heat. There was another thermostat (trip thermostat) that we decided to order and try...bingo...that was it. Now it works like a charm.

Dryer didn't heat. I got the heating element thru sears and when I ordered it I thought I should also order the thermostats but I didn't. Element arrived two days after ordered right on time. Slipped right in in a few minutes. Turned dryer on. No heat. Went back to drawing board. Watched videos on part select site and realized I needed thermostats. Ordered them and lint filter. Arrived right on schedule and also slipped in in no time flat. Turned dryer on and yes it heated perfectly. Wife was pretty impressed with new lint filter as other one was torn with jagged edges. MY SUGGESTION: if your dryer doesn't heat and you can't test each individual item thermostats and heating element order the three of them ( high limit and cycling thermostats and heating element) cause they'll probably will all go at the same time anyway. Then won't have to wait on the second shipment if things don't work with partial replacement. Parts select was great and videos are well understood and easy to follow. Would certainly use again.

I have not received the parts yet waiting on the motor, can’t put the blower fan in without the motor, ordered it , Jan 23rd, still no motor, have to go to laundry mat, have you ever had to do that with 7kids, and you and your wife’s laundry, probably not, because you would have had your motor by now. Maybe you can help me with the part so I can redo a testimonial here for you. 19 days and still waiting

Paid an extra over night fee Friday $24.00 didn't get it until Tuesday afternoon all in all it cost $51.00 then that wasn't the problem.

Easy, just snapped it

Pulled the dryer away from the wall took back cover off the dryer. Used volt/ohm meter to identify the bad element. Ordered the element it came in two days. 2 screws and 2 wires to plug in and we were back to drying cloths

Un plug or remove power before you start. First you would have to remove the rear panel of the dryer. All you need is a quarter inch nut driver. Then look at the bottom right side of the dryer. There you will see the heating duct. At the very bottom is where the element is. There are two screws on both sides( they will all be removed with a quarter inch nutdriver ). After you have removed the four screws holding the element on you will have to remove two wires from the elemet be sure that you mark them and dont mix them up. You will also have to remove the round temperature sensor because you will have to reinstall it on the new element. Then you get new element and reverse the order of my directions. Good luck and be safe ALL WAYS REMOVE POWER BEFORE WORKING ON ELECTRICAL APPLIANCES.

thought the heating element was bad, once inside the element
looked good, tested continuity , tested good.
further test revealed I only had 110 volts at the wall outlet,traced problem to fuse blown in disconnect box under
the house.
Did not need the heating element.luckily parts select is taking the new element back since I did not use it.
Hope this review helps.

Replaced power cord, terminal block, and all melted wiring. Checked the thermal fuse for zero resistance.

I knew that the dryer needed a new belt and since the dryer was also failing to dry the clothes in one cycle, I decided to replace the three thermostats, figuring that I might as well do all three if I'm going to open up the dryer. I downloaded a schematic of the dryer from the Whirlpool web site, which helped me to order the right parts and see how I would be able to make the repairs. Once I figured out how to get to the drum for the belt replacement, installation was quite easy.

First step was to unplug the dryer, remove the vent hose and remove the back panel with a nut driver. Once the back panel was removed, it was easy to see all three sensors. The heating element unit was easy to remove - two screws. This made it easier to replace the sensor. Each sensor was shaped differently, making it easier to decide what went where. This normally would not have been a problem, but the part numbers have changed for this dryer. I could have also cross referenced the parts by using the partselect.com web site.

To access the dryer drum, I had to remove two screws on the back of the dryer that are located in two tabs that hold the control panel to the dryer cabinet. Once removed, it was easy to lift the top of the cabinet and swing it up and against a nearby wall for support while I replaced the belt.
I removed the old belt from the motor pulley, and then just removed the whole drum. I placed the new belt around the drum, placed the drum back in position. With my wife supporting the drum, it was easy to bring the belt through a guide and slip over the motor pulley. Then, I rotated the drum manually to make sure the belt wasn't twisted.

After ten minutes of putting everything back together, it was time to plug in the dryer and test it. I did it without a load first and checked the vent for hot air. After that, we did a couple of loads...one on high and one on perma press, and when the cycle was over, the clothes were dry!

Delivery time from PartSelect was super fast! Prices are excellent, and I really appreciate such a helpful web site. Anyone with a small amount of mechanical ability and "do it yourself" experience can save $$$ by fixing it yourself. Having someone service this dryer would have cost me more just to replace the belt.....let alone the added insurance of replacing the sensors. And, I learned that if the heating element should fail, replacing it would be a snap, and would start with a visit toe partselect.com!

It's amazing... I fixed my dryer!! I am a 47 year old woman with no technical training, and I did it!

I live in a apartment and I bought the Whirlpool Dryer (Model #LER7646JQ0) USED for $150 about 6 months ago. The dryer started blowing cold air, so I called the place that I bought it from and they quoted me a price of at least $300 to fix the dryer.

After searching through google, I found the partselect.com website, and read the repair stories. I decided to take a chance. I ordered just 2 of the suggest 4 parts that could fix the issue, and the dryer did not work. The next day I order the other 2 parts, and that did it - my dryer was fixed.

The diagrams on the site were a little confusing to me (the dryers looks a little simpler inside) but it was easy to repair. I used a screw driver and plier to do the repair, however it would have been much easier if I had a socket set. I would suggest buying all parts suggested, and return the items you don't need. Here are the parts I used:

1. THRMST-FIX (Thermostat, High Limit 221 F
2. USE WPL 279838 (Heating Element (10" long x 6" wide)
3. Thermal Cut-Off Kit
4. Cycling Thermostat (Limit: 155-25) (Thermostat, Internal-Bias)

Good Luck!

Took back cover off. Cleaned out the lint that had built up inside the dryer. Replaced the lint trap housing and lint chute seals. Also replaced the drying vent hose. Works great now.

The first thing I did was call my friend Donnie who manages some apartment buildings and who is always complaining about fixing things and getting the right parts to fix things. He told me what to order from PartsSelect and when the parts got here I called him up and he did the repair work.

He was reluctant to do the work at first but after he found out I had ordered the parts from PartsSelect he was happy to do the work. "Their parts are always right and they always work," was what he said after he had my dryer working just like new. So if you know nothing about fixing things and buying parts just call PartsSelect and you will be fine. Just ask my friend Donnie!!!

I ordered the new handle and installed it in just a few minutes. Very simple--no tools required!

I removed the hex head screws from the back of the dryer and removed the back panel, after unplugging the dryer. I tested the various electrical components until I found that the upper limit temp fuse had gone out. Came to partselect.com and found the kit I needed and ordered it. When it came in, I replaced the upper temp limit fuse, and the other parts that came with the kit. I also, since the back was open, used the opportunity to vacuum out the blower fan and as much of the lint as I could get to. Dryer works great now!