4KNED5800TQ1 Amana Dryer - Instructions

Followed the video instructions that I was directed to through this site. The time it took me includes the time I used to vacuum out the back of the dryer and remove lint build up. The repair was very easy since the video provides all the information you need in an easy to follow format. I used my cell phone and paused when I needed to. Great site, great access to parts and great service. My parts were delivered in 2 days!

I received the part I ordered immediately and the included instructions made installation a snap. Thank you for your help. I would not hesitate to order from your company again.

The dryer stopped heating, it would only blow cold air. I removed the back panel and tested the thermal fuse with a dmm. The fuse was open, so it was bad and I needed a new one. I tested the thermostat and the dmm measured continuity across the terminals, so I thought it was good, bad assumption. I ordered a thermal fuse from partsselect and it came with a thermostat. Like a dummy, I only installed the fuse. The 1st time I ran the dryer the fuse blew again, because the thermostat was bad. So, moral of the story, install both parts.

1) removed the old broken filter
2) deposited it in nearby wastebasket (with lint attached)
3) used scissors (see above) to remove plastic cover from new lint filter
4) inserted new lint filter
5) marveled at my handiwork!

Very easy to replace.

Changed out the lint filter

Dryer ran with no heat. Replaced the Thermal Fuse and when that didn't fix the problem discovered the element was burned. Easy fix except the F-disconnect fitting broke when I tried to remove it and male fitting on the heating element is 0.375 and all I could find were 0.250 F-disconnect fittings. I finally found a supplier who had a 0.375 fitting and the repair took 10 minutes after that. The online videos at PartSelect are excellent.

nobody has said it yet so... to take a dryer apart, take the back off, pull the lint trap, remove two screws on back of the top piece. the whole top shifts forward and disengages two clips on front corners, it then tilts up and back. the front comes off next, this frees up the tub. all parts ordered replaced worn parts, though there was no smoking gun as to the source of the sound. once it was apart, it was a cakewalk. had it up and running in 45 minutes. can't see how it took others two hours.

I am a teacher and teaching is my game. I have always, with my four children, taught them to do mechanical work themselves. I and most of my children have a PhD, but in having said that, I confess, we come from a very mechanically talented family. It shows and proves to be of great benefit.
OK, so much for the intro.

I gave my daughter the tools and said, "What do you think is wrong with the dryer and where would you start?" She tested it and said, "The motor is running, but the tub is not turning thus I conclude it is the belt because I can hear the motor running eliminating that as a cause.

She then opened the top, looked around and removed two screws from the lint catcher. She looked it over, looked a me, I shrugged my shoulders and she then took a rubber hammer and popped the top off. Don't ask me how she knew that, but I think she saw the rubber pins through the crack between the case and top. She raised the top after removing two screws in back to relieve the simple hinge and also disconnected the wiring clip and sure enough, the broken belt was inside the cabinet. We called you, the best, fastest and most accurate service on the Internet and ordered a replacement. I would like to add, the price is always more than fair and delivery very prompt.

When the part came, my daughter took it up to our laundry room and within twenty minutes, she tested it and everything was fine. She did smell a little burning smell which might be attributed to a new belt or the fact that there was no clothing in the dryer.
Thank you so very much.
Dr Robert E McGinnis

Take the door off of the dryer. Lay it on a towel. Remove old gasket. Clean the channel the door gasket fits into with glue remover. Squeeze high temperature glue into the channel, let the glue set up. Put the new gasket into the channel, tape it down in a few places. Let it sit 24 hours for the glue to set up. Put the door back on. You can put the door on immediately as long as you don't use the dryer for 24 hours. Easy.

I followed the instructions on the video and it was simple. The hardest part was vacuuming out 32 years of lint from around the motor and igniter. I was lucky there was never a fire in the dryer.

I opted to remove front, top and back panels. This is best done with dryer laying on it's back so drum remains in position. Hold panels and pieces in place with masking tape (2") You should block up the dryer so you don't damage the gas pipe. I opted to total shop vac out the piece and lubricate the rollers and tension pulley. I made more in change than the belt cost!

Overall an easy repair. Belt came with diagram for easy threading the belt.

Used the video to remove the top and front. Removed the drum. Removed the spindle through the whole next to the spindle. Vacuumed a ton of lint in the dryer and vent pipe. Reassembled in reverse order. Easy repair and a good time to clean the lint.

It required no tools, just take out the old torn filter and slip in the new one. I should have ordered it a year ago, with the ease of the website and the delivery via Fed Ex. super easy.

I simply removed the back panel (6 screws), removed old switch, swapped wires and reinstalled. Varied repair. That easy