LE8207W2 (PLE8207W2) Amana Dryer - Instructions

popped up top of dryer -- With pliers squeezed clips on inside of latch - - with screw driver pryed latch out -- just pused new latch in.......... Thanks to parts select for sending part sooo fast.. wife was happy.. Thanks, Dale

Had to figure out how to open the dryer - bottom screws in front and work up, removed the drum and found the fan blade was broken. Had some difficulty removing the fanblade from the motor shaft but after that the new one was easy to install. I did need help to place the belt and drum back into place. as one person has to hold the belts on the pulley while the other adjusts the belt while putting the drum back into place.

At first i thought i had to buy new dryer, because i did not know what to do.I said, i never done this kind of repair before, well i put everything apart and notice that the idler pulley was worn out, then i said this is something that i can fix it if i get the part. I made several calls and couldn't find it. so went in internet and found it with you.

Simple,I unplugged the dryer and took off the panel located below the dryer door. To do that unscrewed 2 small screws on the underside of the panel. Once that was off I used a flashlight to locate the heating element which was in the rear of my Amana. Using a socket attached to a screw driver I turned 4 screws out of the element and it was free. I brought the element closer and compared it with the new element and made note of the wire pattern. I plugged in the new wires I received in the box into the new unit and then one by one unhooked the wire leads coming out of the dryer. I reversed the above there it was...maybe 30 minutes!

Unpluged dryer from outlet, disconnected vent, positioned dryer on side, removed screws from bottom panel, pulled pannel away from dryer body to gain access to motor. Disconnected drum belt from motor pulley, disconnected wire harness from motor. Removed motor mounting bracket assembly and placed entire assembly on floor. Removed clamps and blower assembly from old motor, installed new motor and reassembled. Very easy project, hardest part requires some trouble shooting knowledge to determine the exact cause of problem.

Opened things, saw lint buildup, cleaned inside of dryer, then cleaned entire vent discharge system, put new thermal fuse back, turned on dryer and heard metal to metal, opened dryer back up, saw missing glides (both gone). Ordered what I thought were 2 glides, 2 days later 1 showed, called and was told I didn't "update" when I changed order info (parts supplier cautioned to replace 2, should only sell in pairs) so then had to wait again for 2nd glide to show up. Replaced them today and noticed dried clothes are now cooler when finished. Will note in future if clothes are warmer, clean ductwork.

i am sorry i dont know all the technical term but here it goes, first I turned of the electrical breaker to the dryer, I unpluged the dryer and disconnected the dryer hose to the outside of home, I removed front dryer panel, remove front of drum panel, removed belt and found it to be worn, removed drum, removed the wiring connected to the back panel that had heating element inside, removed the back panel, removed the heating element inside the back panel and then reassembled unit. I had question whether or not it would ever run again, but it is working fine. Thank you for your prompt attention with sending the parts. i dont know if there was a different way to solve this problem, but i felt if there was an expection plate on the side of the unit, it would be helpful.

I followed the instructions found on this site. The hardest part was figuring out how to release the clamps at the front of the dryer so I could remove the top.

The key was to unbolt the clamps at the back of the dryer first, then to use a putty knife to release the two clamps at the front of the dryer that hold the top to the front.

The rest was easy by following the steps already listed on this site and removing the two front pieces, then the drum and replacing the parts. Putting it back together was simple since I placed things in order and had taken pictures with my cell phone as I went through the process.

The time I took, included vacuuming the inside of the dryer thoroughly. Now it runs like new.

After taken apart to replace high limit thermostat fuse and limit thermostat took about 5 minutes. Also our dryer always ran very hot no matter what setting it was on. Replaced idler pulley wheel also because seemed not to rotate very well. Put all back together and worked perfect. Ran and does not overheat now.

1.Unplug unit
(gas model, did not shut off)
2. Remove bottom front panel-2bolts
3 Remove main front panel-2 bolts (no need to remove door)
4. Make note of wire colors on door switch and light, disconnect
5. Remove 3 screws that hold air duct assembly(that lint filter rests in) then set main front panel aside
6. Remove lower air duct (to blower motor)-3 bolts
7. Lift and tilt-up top lid/panel of dryer and wedge wood or ? (this will give you easy access and better light)
8. Reach back behind motor to move idler pulley and remove belt from motor & idler pulley
9. Remove 4 bolts and lift up and out front bulkhead frame that holds drum in place
10. Slowly pull straight out & slightly up entire drum
11. Remove circlip/retaining ring, washer, roller, washer and shaft assembly.
12. Vacuum entire unit
13. Light lubricant on shaft when reinstall in reverse order.

Snap ring pliers and a mental note of how the belt is routed on idler will prevent unwanted profanity.
This is an inferior/substandard unit before Maytag bought them. Spend the money and replace both rollers with new shafts (about 50.00). I have spent over 140.00 in parts to keep this unit running (less than 8 years old). So do the math before you start pouring money into this model.

Replaced glides and assy idler pulley cleaned all parts fron dust and debree, vaciumed heating eliment to remove all excess lint and wool to make sure I did'nt have a fire in the lower unit.
Job was'nt all that hard just have to watch what you're doing.

Using instructions from your website, I was able to remove access covers from my driver & find the pieces that needed to be replaced. It was a simple repair job & now my dryer is working properly again.

Removed all of the front outer bolts holding in the lower plate, front door assembly, drum outer frame and drum. While removing the outer sheel there are colored wire connections that activate the linterior light and door sensors in which I marked the interior sheel with a marker so I knew which wire went where. Before removing the drum I drew a sketch on how the belt is ran thru the pullys and around the drum, so I would have no problem reinstaLLING IT.The rooler bracket was easily removed with a socket wrench and the retaining wring was pried with a pliers. Reinstallation of the shaft, roller and ring were as simple as removal. I then cleaned the entire interior and lint basket for optimal performance. The most difficult part is pulling the belt back around the drum, but still not very difficult. Finally I reattached nall removed parts as they were removed and I now have a like new dryer for about $20.00 vs, buying anew one or repair fees costing Hundred$ OF DOLLERS.
Thanks Partsselect.com Again!

The belt tensioner was the problem and the belt had very fine cracks in it so I ordered four parts: the belt tensioner, belt and the two drum rollers. I had to work to clean the fan and the LARGE dust bunnies. I'm writing this to encourage others to consider installing new duct work, mine was becoming a fire hazard. At a minimum clean all the duct work. Your dryer will work so much better. Thank you for your printable help!??

Took dryer apart, and found that the idler arm pulley was in pieces. Ordered the replacement from Partselect.com. Received part very promptly. Decided to also order a new belt, and that arrived in a very timely manner also. Put the parts in, and assembled the dryer. This was for my 90 year old grandmother, and she is ever so pleased that it is up and running again. Completed the repairs for about $50, and saved big money by doing it myself versus a service call, that would have boiled down to replacing the unit for the price it would have cost to fix. Will use partselect in the future for all my appliance repairs, as they offer a great selection of parts for all different appliances. Very pleased with satisfied with quality, and service from Partselect.com