4KAED4900BW1 Amana Dryer - Instructions

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Took the old filter out and inserted the new one- works great!!

I replaced the thermistor earlier, but the code was still flashing. I noticed the heater terminals were charred and pretty well covered in carbon. So, I replaced the heater, the thermostat and thermal fuse and replaced the 3/8" spade terminals on the heater wires. (These are hard to find - most electrical spades terminals are .250. Also, I crimped and soldered these for a connection with the lowest resistance possible). After all that, the code still flashed! I let the explatives fly, calmed down, and ran the control board test. (This is done by pressing "more time" "less time" "more time" "less time" in succession.) The control board was passing all the tests, but the thermistor test, and the only thing is in this circuit is the thermistor, the wires, the connector to the control board, and some circuit on the control board that involves a few resistors and the "brain" chip. So, I checked the terminals at the thermistor, the wires up to the control board and the connector at the board. The control board connector was fairly dust encrusted, so I unplugged it, cleaned the control board terminals and sucked away all the lint and dust. Finally, I carefully removed earch crimp terminal from the Molex connector (the white female connector) and cleaned and bent them to yield a better connection to the terminals on the control board. I put it all back together, and thus far it is working fine.

Used socket set to remove the two hex-head screws from the bottom flange of the toe panel. Manually pulled the panel out at the bottom, pulled down, and removed the panel. Looked to right and found heater shield. Removed heather shield using socket set. Removed the two wires from the terminal block (had to use a little WD40 to loosen connection and wiped up afterwards). Removed the holding screw holding the heating element using the socket set. Pulled HARD on old heating element using pliers and a rag (protection from accidental cut-sharp edges). Once out, the new element slid in relatively easy. Screwed the new element back into place and re-connected the element wires, then put the heater shield back into place. Put the toe panel back into place. Tested and worked great! The only thing that made this "easy" but not "really easy" is that I had to really pull HARD on the old element to get it out...with the sharp edges and tight fit in play, you'll need to pay attention to safety when removing the old element.

Pulled out the old and slid in the new filter

I'm still waiting on my idler pulley. It arrived at Fed EX depot in Tracy CA on December 14th and has still not been shipped. So it is pretty fucking hard for me to install it! Maybe if you had customer service that would answer their phones or reply to my Emails would be helpful

Unplugged dryer. Removed dial. Removed old timer (3 screws) and left wires attached. Installed new timer. Disconnected wires from old timer to connect on new timer. Plugged in dryer......everything worked again.

I followed the repair Vedic and took the drum out and replaced the pulls and bracket. Very straightforward job. Dryer is now as quite as the first day we bought it.

Received in two days, open box, installed part. Pretty easy, fast service. I'm a repeat customer and will use these guys in the future.

my dryer door didn't latch for over a year. We were accustom to proping large objects against it. a friend told me to look on line. The close up pictures and parts diagrams were awesome. It was here in 4 days . Now my family thinks I am a hero. The end

I noticed that drying time was increasing. I took the covers off the dryer to reach the fan and discovered that the squirrel cage fan buckets were packed with lint, and therefore not moving the air as intended. This was because the original lint filter caught most of the lint, but some bypassed the lint filter and then built up in the fan wheel buckets. The lint bypassed the lint filter because there was no felt gasket on the original filter as far as I can tell. I replaced the lint filter...and the replacement filter includes the felt seal (and fits tightly in the slide). The original lint filter has a provision for the felt seal, but I don't recall ever seeing it (and I did not see remnants of it in the fan or duct). As a matter of fact, I was always suspicious of how loosely the lint filter fit in the slide. The felt seal is not available as a replacement part from Maytag. That said, felt material 3/16"x1/2"x10ft is available from McMaster-Carr...and it fits nicely in the original lint filter.

Removed the two screws under the lint trap
Opened the top (had to use flathead screwdriver to release latches)
Disconnected door switch harness from front panel
Removed 2 screws holding front panel on dryer
Lifted out dryer drum (previous belt had broken)
Vacuumed inside of dryer (found $3 in quarters!)
Put new belt around drum
Put drum back in dryer, using empty laundry soap bottle to support its weight
Looped belt around pulley and motor; secured pulley to dryer bottom
Made sure rear gasket thingy was aligned properly and drum turned freely
Put front panel back on
Re-attached door switch
Closed top and put screws back in under lint trap
Fired it up - WOOHOO!

Used my Whirlpool Dryer User Instructions Manual and followed instructions and used the Cabinet Parts page to see the diagrams.

Repair job took less than 10 minutes: 1) Unplug Dryer 2) Remove Lint screen and 2 Phillip screws 3) use flat putty knife to depress lid latches while lifting (latches located approx 2 - 3 inches from each side. 4) unplug defective door switch 5) remove 2 Phillip screws that secure the door switch. Reinstall switch repeating the above steps in reverse order and your done.

I raised the top of the dryer, removed the front, the belt and the drum. Slipped off old rollers, installed new ones and new tensioner. Reinstalled drum and belt, bolted front back on and closed the top.