4KAED4900BW0 Amana Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Scott from WOODBURY, MN
- Parts Used:
- W10120998
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
lint screen was not catching lint and sending out the dryer vent
replaced dryer lint screen with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from WARREN, NJ
- Parts Used:
- 279570
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer door latch broke and door wouldn’t stay shut.
Jimmied out the latch using two screw drivers to get under the edges. Pushed the new piece in. Voila! Took 2 minutes for what my repair man told me would cost about $200 to fix. Unbelievable!!( I first watched some YouTube videos to get the idea )
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from SALLISAW, OK
- Parts Used:
- WP3387747
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Heating element went out.
Followed the instructions all went good except for the sliding the shield back in it didn't want to go back in but it does fit. Dryer works like new again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joan from MANLIUS, NY
- Parts Used:
- 4392065
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Loud screeching when dryer tumbles
We had to pop open the top. Unscrew front of dryer from sides. Disconnecting the wires was a bit more difficult than expected. We had to use a tiny screwdriver to slide into the sides of the white wire connector on each side before pulling apart. Front drum falls when front of dryer is removed. It took two of us to reassemble - one to hold the drum while the other put the front on. Our problem turned out to be one wheel. We replaced both wheels and saved the rest of the parts. Hums along just fine.
Was this instruction helpful to you?
Thank you for voting!
HEATING ELEMENT open circuit
replacing the heating element was difficult due to the small area to work with and the defective element was difficult to slide out from housing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Rocky Mount, VA
- Parts Used:
- 4392065
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Loud rumble and finally the drum stopped because the belt broke
I opened the top and front of the dryer. 1st I pulled out the drum and cleaned up the lint and mess from the busted support roller. Next it was a matter of looking at the enclosed drawing and instructions. I could not believe it was that easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from S SAN FRAN, CA
- Parts Used:
- WP3387559
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Left hand door hinge broken.
Snapped the bottom front panel off by using a flat tip screwdriver on the clips holding the panel on. Then I had access to the spring which I pulled off the bottom mount with my pliers. Pulled the door open to unscrew the left side hinge and then replaced with the new one and pulled the spring back up on the top hinge and bottom mount. Then I snapped the bottom panel back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from CALIFORNIA, MO
- Parts Used:
- 661570
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Broken belt
Disconnect gas line and vent hose,removed top and back covers to install belt.
Was this instruction helpful to you?
Thank you for voting!
Dryer door won'y close/ hinge's bent
Well my husband did it for me, but very easy to fix, unscrew the bolts, take the door off, take off both hinge's which is attached to springs and replace, put it all back together, door fixed and closes nicely.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from SCHENECTADY, NY
- Parts Used:
- 4392065
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Broken dryer belt
Took the two screws holding the lint trap to top. Used a putty knife to loose the clips holding the top of the dryer up so it could be hindged up for access. Used a nut driver to remove the four screws hold the front door on. Removed the lower dust panel, just clips holding in on. Pull the dryer drum out along with the broken belt and old belt tensioner. Took shop vac and cleaned lint and removed about $2.00 of loose change from the base. Installed the new drum supper wheels. Held belt around drum to put back in. Looped the belt through tensioner and around motor drive pulley as shown in instructions. Put front door on only to find the felt around the door had slipped making the drum hard to turn. Pulled the door back off and laid the dryer on it's back before putting the door back on , so you can run your hand around the door to make sure the felt go inside the drum. Put the four screws back in the door panel before uprighting the dryer. Sucess the drum turned freely. Put other remaining panel and srews in lint trap . Hook the dryer back up to vent, power and gas, and turned on the dryer. Runs like new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindy from BENZONIA, MI
- Parts Used:
- W10120998
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Screen ripped
Dropped new filter in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from CARY, NC
- Parts Used:
- W10120998
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The lint filter needed replacement due to what is probably normal wear and tear.
I searched for a replacement by entering the model number and serial number of my Kenmore elite dryer. Ordering was extremely simple and it took less than a week to arrive. It fits perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- braulio from FORT WAYNE, IN
- Parts Used:
- WP3387747
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Not heating up
I just took the old element replaced with the new one i order from this site, I save some money was really easy so proud of my self...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from PUNTA GORDA, FL
- Parts Used:
- 4392065
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Will Not Tumber
I use the manentance kit that was not the problem. I end buying the drive motor and that was it. I was happy with the service I got from part select, overnight mail what more could I ask for? I am also glad I replace everthing with mainentance kit. Thank you for your help john degnan
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from LOGANVILLE, GA
- Parts Used:
- WPW10237959
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Broken dryer door switch
Never did get the part. Initial order was not the right part. Ordered the right part on 12.2 and this is 12.18. While the initial oder and delivery was correct, they do not tell you that you do not have to ship by Fed ex. Fed Ex seems to not be able to provide service to our address despite driving past it several times a day.
Was this instruction helpful to you?
Thank you for voting!