4KMEDC100BQ0 Amana Dryer - Instructions

Removed top cover. Removed front cover. Removed Drum. Located the broken belt. Found that there was no tensioner in the unit. Replaced drum rollers. Put in new tensioner. Repaced Drum with belt around it. Installed belt through tensioner and onto drive pully of motor. Supported Drum with wood block. Turned on dryer to insure drum turned without any problems. Removed wood block. Replaced front cover and top cover. Repair compete.

I squeezed the latch catch with a pair of pliers and pushed it in the catch hole. But that was the final repair. There were two "repairs" before that. First, we used two commercial grade rolls of wide plastic tape to tape the dryer door shut each time we used it, for a year, until we ran out of tape. Second, we positioned a chest of drawers in front of the dryer and wedged a 1" x 4" against the door. Very effective. Then I broke down and ordered the $3 catch.

I changed the belt, tension pully and rollers. Runs like new now. I also took the opportunity to clean it out real good while I had it apart.

The pulley is accessible from the back of the dryer. Disconnect the gas line. Remove all the screws. Also remove the small plate that secures the line cord. Lift the back up and out. I was able to avoid disconnecting the water line. Take a picture of the pulley so that you will have a record of the belt routing. Release the spring and remove and replace the pulley and bracket. Vacuum out the lint. Plug in the dryer to make sure that it works properly before reassembly.

I ordered this to repair my girlfriend's mother's dryer. But according to my luck, the day the part was to arrive, I suffered an small brain bleed that put me in the hospital for a couple of weeks. I had read the instructions and was able to explain it to my girlfriend who replaced it and got it all back going right!

Couple screws behind the electrical panel at the top and the top pushed back and was able to remove front panel, and then it was pretty easy. Take the two screws on top front, lint trap screws . The lint trap vent needs to come off. Then the belt, drum comes out to access the idler pulley. I did replace two drum wheels, I saw there was 5. I would recommend replacing all of them, they didn’t move well…..

Remove screws, dryer sensor on screen. Put sensor back in place. Secure with screws. The way you take it off go in reverse.

We had to pop open the top. Unscrew front of dryer from sides. Disconnecting the wires was a bit more difficult than expected. We had to use a tiny screwdriver to slide into the sides of the white wire connector on each side before pulling apart. Front drum falls when front of dryer is removed. It took two of us to reassemble - one to hold the drum while the other put the front on. Our problem turned out to be one wheel. We replaced both wheels and saved the rest of the parts. Hums along just fine.

I opened the top and front of the dryer. 1st I pulled out the drum and cleaned up the lint and mess from the busted support roller. Next it was a matter of looking at the enclosed drawing and instructions. I could not believe it was that easy.

Followed the instructions all went good except for the sliding the shield back in it didn't want to go back in but it does fit. Dryer works like new again.

Jimmied out the latch using two screw drivers to get under the edges. Pushed the new piece in. Voila! Took 2 minutes for what my repair man told me would cost about $200 to fix. Unbelievable!!( I first watched some YouTube videos to get the idea )

This could not have been easier. The hardest part was tipping the dryer over on its' side.
Instructions:
1. Tip dryer over onto a non-scratch surface. I used a tarp on the floor.
Insert leveling foot into the foot opening on the bottom of the dryer &
screw in with fingers until it is difficult to turn.
2. Use the adjustable wrench on the hexed foot (not the threads) to adjust to the desired level.
3. Tip dryer upright taking care not to exert pressure on the feet closest to floor. I used a folded-up tarp under the bottom edge of the dryer while lifting it to the upright position.
4. Use a level, back to front & side to side, to determine if feet need further adjustment.
5. Adjustments can be made with the dryer in the upright position, using the adjustable wrench on the hexed foot.

replaced dryer lint screen with new.

Removed the top, removed lower front cover, removed the front, removed the belt, removed the drum and the back. Removed and replaced roller support shaft and drum roller’s. Completed all Front and rear support for drum. Replaced drum , replaced drum roller belt and replaced back, completed replacement of the top, front.

replacing the heating element was difficult due to the small area to work with and the defective element was difficult to slide out from housing.