4KNED4605FW0 Amana Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dillard C. from Vina, AL
- Parts Used:
- WPW10512946, 349241T
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
drum roller became lose and seperated from the shaft that supports it. it had to be replaced
remove the front panel, belt [notice the way the belt is fasten] remove the tub, support bracket to the drum roller, and slide the new drum roller on and place the tre ring in the slot. then re-install everything in reverse
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gwendolyn from BAKER, LA
- Parts Used:
- W10857612
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
My Dryer Timer broke off at the plastic part.
My son took the timer hood off with a Phillips, head screwdriver and replace the Timer. Then he put. Tim hood back on the dryer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from New Bedford, MA
- Parts Used:
- W11778253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken handle
1) removed the old broken filter
2) deposited it in nearby wastebasket (with lint attached)
3) used scissors (see above) to remove plastic cover from new lint filter
4) inserted new lint filter
5) marveled at my handiwork!
2) deposited it in nearby wastebasket (with lint attached)
3) used scissors (see above) to remove plastic cover from new lint filter
4) inserted new lint filter
5) marveled at my handiwork!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Dayton, TX
- Parts Used:
- W11778253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lint Filter wore out had to be replace
Changed out the lint filter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from VASS, NC
- Parts Used:
- WPW10359270, 349241T
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
The drum made a lot of noise while turning. The dryer shook
Used the video to remove the top and front. Removed the drum. Removed the spindle through the whole next to the spindle. Vacuumed a ton of lint in the dryer and vent pipe. Reassembled in reverse order. Easy repair and a good time to clean the lint.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Claude from Austin, TX
- Parts Used:
- W11778253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lint Filter wore out.
It required no tools, just take out the old torn filter and slip in the new one. I should have ordered it a year ago, with the ease of the website and the delivery via Fed Ex. super easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from VENICE, FL
- Parts Used:
- W10861225
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The dryer door handle broke.
Replaced with new handle in 10 seconds
Was this instruction helpful to you?
Thank you for voting!
drum stopped
10 min. job, easy to do / two screws top and two inside front / remove old parts install new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paula from SUNRISE, FL
- Parts Used:
- W10861225
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
handle broke off
I easily popped the new handle on in 3 seconds
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christine from Virginia Beach, VA
- Parts Used:
- W11429587
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken door catch
The original door catch had broken and would no longer stay shut. Ordered the part from this site with ease. Very easy to replace the broken door catch on my Amana dryer. Tool needed was a flat head screwdriver to loosen the cover, remove broken piece and easily replace with new part. Followed the video and it was back to normal operation within minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Evelyn from JACKSONVILLE, FL
- Parts Used:
- W11778253
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Needed a new lint filter
Took the old one out, replaced it with new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from LEMOORE, CA
- Parts Used:
- 4392067
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Coin op Whirpool Dryer Broken drive belt and frozen drum wheels
Removed two hex screws from upper back clips. Removed 2 Phillips screws under lint trap. Used flat head screwdriver to pry up top on front right and left side clips. (FYI: top pry's up off retaining clips in front). Remove two hex screws on right and left front panel. Un-plugged wire harness front right side. Lifted up and removed front panel. This hold the drum in place. Simply removed drum, installed new belt, replaced the two drum wheels and put everything back together the same way I took it apart. 30 Minute project :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Rocky Mount, NC
- Parts Used:
- 341241
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Let the kids do it.
I am a teacher and teaching is my game. I have always, with my four children, taught them to do mechanical work themselves. I and most of my children have a PhD, but in having said that, I confess, we come from a very mechanically talented family. It shows and proves to be of great benefit.
OK, so much for the intro.
I gave my daughter the tools and said, "What do you think is wrong with the dryer and where would you start?" She tested it and said, "The motor is running, but the tub is not turning thus I conclude it is the belt because I can hear the motor running eliminating that as a cause.
She then opened the top, looked around and removed two screws from the lint catcher. She looked it over, looked a me, I shrugged my shoulders and she then took a rubber hammer and popped the top off. Don't ask me how she knew that, but I think she saw the rubber pins through the crack between the case and top. She raised the top after removing two screws in back to relieve the simple hinge and also disconnected the wiring clip and sure enough, the broken belt was inside the cabinet. We called you, the best, fastest and most accurate service on the Internet and ordered a replacement. I would like to add, the price is always more than fair and delivery very prompt.
When the part came, my daughter took it up to our laundry room and within twenty minutes, she tested it and everything was fine. She did smell a little burning smell which might be attributed to a new belt or the fact that there was no clothing in the dryer.
Thank you so very much.
Dr Robert E McGinnis
OK, so much for the intro.
I gave my daughter the tools and said, "What do you think is wrong with the dryer and where would you start?" She tested it and said, "The motor is running, but the tub is not turning thus I conclude it is the belt because I can hear the motor running eliminating that as a cause.
She then opened the top, looked around and removed two screws from the lint catcher. She looked it over, looked a me, I shrugged my shoulders and she then took a rubber hammer and popped the top off. Don't ask me how she knew that, but I think she saw the rubber pins through the crack between the case and top. She raised the top after removing two screws in back to relieve the simple hinge and also disconnected the wiring clip and sure enough, the broken belt was inside the cabinet. We called you, the best, fastest and most accurate service on the Internet and ordered a replacement. I would like to add, the price is always more than fair and delivery very prompt.
When the part came, my daughter took it up to our laundry room and within twenty minutes, she tested it and everything was fine. She did smell a little burning smell which might be attributed to a new belt or the fact that there was no clothing in the dryer.
Thank you so very much.
Dr Robert E McGinnis
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from NEOSHO, MO
- Parts Used:
- W10861521
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Bad door gasket
Removed old seal and replaced with new one. Save yourself time and get some acetone to remove old glue works great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- george s from las vegas, NV
- Parts Used:
- 341241
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Dryer Drum Belt Broken
I opted to remove front, top and back panels. This is best done with dryer laying on it's back so drum remains in position. Hold panels and pieces in place with masking tape (2") You should block up the dryer so you don't damage the gas pipe. I opted to total shop vac out the piece and lubricate the rollers and tension pulley. I made more in change than the belt cost!
Overall an easy repair. Belt came with diagram for easy threading the belt.
Overall an easy repair. Belt came with diagram for easy threading the belt.
Was this instruction helpful to you?
Thank you for voting!