DLE330RA-PDLE330RA Amana Dryer - Instructions

This amana dryer didn't have the lower panel with screws. Instead, I removed the brackets in the back and found that the whole top would separate from the rest of the body (except for wiring, of course.) There seemed to be screws holding the top to the base in the front, but these are just guide posts. There are two spring clips in the front that you can pop loose with a putty knife.

Then there are two screws inside that fasten the front to the rest of the frame. Once I removed these, and the electrical connections to the door switch and the light bulb, the whole front came of just by tilting it forward and pulling the front panel up off of metal tabs on the base.

The rest of the repair went smoothly per other descriptions.

I first removed the front panel and door on the dryer using a 5/16th nut driver. I needed to disconnect the light and switch to remove the door. I raised the top lid of the dryer to expose the drum. I rmover the fan schroud and lint filter by removing 4 5/16 screws with the nut driver. I disconnected the belt from the idle tension pully and removed the drum. The drum support rollers were visible on the back frame of the dryer. I removed the bad roller using snap ring pliers. After cleaning the roller support shaft and lubricating the shaft with grease I replaced the drum support roller and secured it with the snap ring. I also replaced the dryer belt although it was still workiing. I reasembled the dryer after giving the inside a cleaning with the shop vac. The hardest part was getting the belt secured with the tension idle pulley. When assemblying the fan schroud make sure it is snug against the fan so it doesn't leak. Replace the top and front door and cover connecting the switch and light. If you get the switch wires correct the dryer will run with the door shut otherwise reverse the wires.

As it turned out, the felt was only part of the problem. The guide bracket had been cut thru by the drum. This all started when a golf tee got stuck in the drum area. It took very little time to destroy the guide bracket. Dryer was built by Whirlpool. Parts are built to the bare minimum. These appliances are designed to break in a couple of years. There is no doubt about it. I installed the new guide brkt, glued the new felt on and put it all back together. The job is pretty straight forward but you need to be mechanically inclined.

Had to lay dryer on back. Cause it didn't have a back cover had to take the front door off and go in thru the front. Had to take the vent off. Had to use scotch tape to hold the belt in place while I got it on. It would have been a lot easier if they had a back cover. I only hope I don't have to do it again as it squells a bit on start up. Bill

First we had to virtually take the entire dryer housing apart - not very user friendly. We found that one of the two mounting screws on on of the rollers was gone. The mount was just wobbling around which caused the roller to fail and all of the noise. The wheel removal was a bit tough since there is very little room to pull it up and off of the center post. Definately need at least one helper to pull up on the drum while the wheels are removed and installed. Once the two new rollers were in place, the dryer worked like it was new. Not an easy job, but very do-albe - saved a ton of money doing it myself. Two must - haves: good set of snap ring plyers and one patient helper.

I took out the 2 screws on the bottom of the front cover, pulled out at the bottom, disconnected the 2 wires for the front door and removed 2 screws on the inside top of the front panel and removed. The top of the dryer then flips over. I then tool out 4 more screws and took out the drum. I totally cleaned out the inside of the dryer and then took the oring pliers and removed the oring that held the roller on the belt tension bar and replaced it with the new one that you sent me. I put the drum back in and put the belt back on the new roller, I put the dryer back together and now I have a good dryer that will last another 10 years.

I first replaced the blower fan, then noticed excessive heat. That was the reason the blower fan came apart. Watched some videos on the symptoms and ordered said thermostat. I removed lower front access panel, thermostat is on exhaust side of blower fan housing, removed 2 screws transferred the 3 wires installed new thermostat and done.

Went to YouTube and put in good.. did not fix the problem with the dryer but it has a new belt on it now!

We received the parts in two days. We installed the new lint duct assembly in about 30 minutes. We unplugged the dryer and lift ed the top of the dryer removed the front of dry we disconnected the wiring and then removed the damaged lint duct . Cleaned the lint off the dryer and replaced the new lint duct. screwed the front back on . Reconnected the wiring clips and put the top back on the dryer. The top of dryer had clips that slid the top back on. Plugged dryer in and it works great.

Follow the instructions on this webside

I followed the online video on PartSelect website. No other instruction necessary.

disassembled the entire dryer drum and front bulkhead plate. Installed belt and replaced drum on rollers and positioned idler pulley .Video was very helpful in positioning drum and belt onto idler pulley. More trouble with the existing dryer vent replacement after repairs were complete

The Dryer is about 25-30 years old. I replaced the motor due to overheating, while I had the dryer disassembled I decided to change out the idler pully wheel and the drum support rollers. This was my first time changing out the motor. Surprisingly, the blowerfan blade came off the shaft of the motor very easy. I was concerned about the age of the dryer and was anticiapating this could be a problem fortunately, it came off very easy. Removing the old motor was easy. The only issue I had was seating the new motor in the correct position. I felt that the motor was not in the correct posiotion however, I was not sure being that this was my first install.
After trying several times, rotaing the motor back and forth (side to side) within the motor holding end brackets the motor fell into place and I was able to put on the end motor clamps on correctly. The drying is now working.

I guessed that a new belt may fix the problem. The repair was nearly as easy as the video suggested. I believe the dryer had been repaired before since there was a circular panel on the side which had been removed. I could reach in through the side to slip the new belt onto the pulley. The new belt now enables the drum to turn even for heavy loads.

I totally disassembled the Dryer, and replaced the Guide Rollers, Blower Wheel, Idler Pulley Shaft, Idler Pulley, and Belt.