LE2102L (P1118302WL) Amana Dryer - Instructions

Disconnect the dryer from the electrical source. Using a nut driver, first remove the 2 screws of the lower panel and release the panel. Next remove 4 screws of the door panel and then remove the electrical connections to the door (6 wires). Remember to mark the wires prior to removing so you will remember were it plugs back in on reassembly. Remove the door panel. Then remove the 2 screws holding the top of the dryer and tilt the top open about 90 degrees to access the tumbler. Remove the belt by sliding off the tumbler. Remove the tumbler. You will then access the pulley. Using a pair of pliers, remove the retaining ring by pulling upwards. Then remove the washer and the pulley. Replace the parts with the new pulley, washer and retaining ring. This time would be a good time to replace the belt too. Thread the belt through the pulley and over the tumbler. Place the top back and screw in place. Reassemble the door wiring and reattach the door with the 4 screws. Reassemble the lower panel and plug the dryer back into the outlet and test. There should be no more noise if the noise is coming from the pulley and loose belt.

Removed old latch. Installed new latch. No problem.

Only needed half the parts. Installed the catch for the door and saved the other part.

The instructions that accompanied the part was extremely helpful. I removed two screws, lifted off the front panel, used the pliers to remove the old latch, pushed the new latch into the hole. I then replaced the panel (The part that is attached to the door was not broken). I tightened the two screws and the job was complete. I saved a very expensive service call. :)

Removed door and front panel. Removed drum. Removed idler pulley arm and spring. Removed snap ring and pulley from idler pulley arm. Reversed process to re-assemble.

Removed the front dryer panels (lower & upper), front drum support and drum. This gave me easy access to the idler pulley and tension spring. I also took the opportunity to vacuum all of the lent that had collected over the years. After installing the new parts and aligning the belt, I reassembled the panels, plug it in and it worked like a champ! Locating the parts on your website was fast and easy. I appreciate it and thank you.

removed old broken piece with screw driver and pliers...
replaced with new part with thumbs as pushers.

used one nut driver, basically took the whole machine apart. took snap ring off the idler shaft, replaced pulley, and put it back together. simple job.

Determined no air flow or heat through system even though dryer spun and timer worked. Ouside vent dispelled no air. Opened dryer panel.
Blower wheel/fan broken off from shaft. Googled appliance parts ... found ... Partselect .... keyed in mfg, model number ... schematics available ... found part ... ordered ... received in two days ... installed ... reassembled. Working fine ! $ 30.00 compared to buying new dryer ! This was a refreshing and rewarding repair. If it could always be this smooth !!! Great resource ... PARTSELECT !

After 20+ years of service, the plastic part that holds the dryer door closed, broke. I orderd the replacement part on a Monday and received it on Wednesday!
By applying constant pressure with my thumb, the replacement part 'snapped' into place - all of 4 seconds.
Fast delivery of parts and fast instal, made for a great day.

remove front panel ,remove top panel,lift drum,slide new belt on to drive motor then idler pulley then put belt over the drum.reassemble in reverse , front panel first

Repair part just snapped into place. It took longer to open the bag then do the repair. I thought it was going to be difficult to find a part for this dryer but partselect had the right part.
Thanks

Pop out with screwdriver and push in new part. easy

I used a screwdriver to pry out the broken door latch and inserted the new one in the same slot. Perfect fit. The picture of the part in the order page was a big help to identify the correct part.

My problem was that my AMANA dryer would not heat. The site suggested testing the two thermostats so I opened the dryer but didn’t follow the instructions in the video tutorial on the site since my AMANA is different. I used a nut driver and needle-nosed pliers for the whole job. Here’s what I did:

1. Unplugged the dryer.

2. Disconnected the exhaust pipe at the dryer.

3. Pulled dryer away from back wall about two feet.

4. Removed the two bottom panel screws (floor level) and removed panel.

5. Removed the two door panel screws and removed door panel by pulling out at the bottom until the two spring clips released from the top panel.

6. Noted the colors of the wires going to the door switch and removed (green, black and white from left to right).

7. Noted the colors of the wires going to the lamp and removed (bottom - black and top - red.)

8. Removed the two top panel screws, lifted up the top panel and leaned it against a support.

9. Removed the four bulkhead screws and carefully lifted up and removed the bulkhead being sure to support the drum. Took note of the belt path around the motor and idler pulleys.

10. Reached under the drum and took the belt off the idler pulley and motor drive pulley.

11. Used the belt to lift and remove the drum through the front opening.

I noticed that the internal vent pipe had become disconnected (which probably caused internal overheating) so I fixed that.

I then removed the wires to the thermostats and tested both for continuity. The limit thermostat was bad. I also saw that the belt was becoming cracked. I ordered a new limit thermostat and belt.

Installation of the new parts was a snap. I removed the old thermostat with the nut driver and replaced with the new one and pushed the wire connectors back on. Replacing the belt was a little trickier but not a problem. (Be sure to route the new belt correctly as noted on Step 9 and place ribbed surface next to drum.)

I closed up the dryer by reversing the opening steps.