LEM847W (P1176709WW) Amana Dryer - Instructions

Make sure to unplug the power cord.Pry the front,top of the dryer up with a screw driver. Carefully disconnect 3 wires and remember where they go, top right. Remove 1 top bolt on each side of the front cover, inside.Pull up slightly and towards towards you to remove the front cover. Disconnect the light wires if applicable and remember where they go from the front drum support. Remove 4 bolts on the front drum mount cover; the lint catcher will come off with it. If needed, pull up and towards you on the drum to lower the it off of the guide rollers to allow slack in the belt. Reach under the drum, raise the idler lever, slide belt from under the idler lever pulley, remove the belt from the the motor shaft. Carefully remove the drum. A 7/16 wrench and ratchet can be used to remove the idler lever from the mount. Remove idler lever from the spring. Reverse these steps for installation of the new idler lever. For installing the belt, actually fold the belt and put it under the idler pulley and back onto the motor shaft. The idler lever should sit on top of the belt when on properly. Make sure the belt is lined with the wear area of the dryer drum. Roll the drum manually, counter clockwise several times to help insure belt alignment before reconnecting the wires and re-installing the front cover and top. A belt replacement will not require removal of the drum.

Parts that were recommended for the noise issue were spot on. Instructions were very helpful and made the job go very smooth. Replaced the belt, rollers don't forget to order (2) felt pad and idler pulley replaced.
The part suggestions for the heat problem did not fix the problem. The burner flame would come on for 2-5 min. then go off. A few min. later the burner would try to ignite but would not start. The igniter would get cherry red but no activation. I end up replacing the coil kit. Turned off the gas removed (2) screws and wala done 5 min. and it fixed the problem.

Well first of all you get to the back of the dryer from the FRONT.. after lower panel was removed location of the heating element was right in front of you. Two 7/16 sheet metal screws hold the heating element in place very easy to remove.. upon removal you will have plenty of room to pull element out and switch out the wires you need to do.. Upon examination I think my trouble was a high limit fuse that burned out, so I propably did'nt need to buy the whole element ( you might want to check that first it is the ceramic one ) cleaned everything out and dryer is as good as new Good luck

First unplug the dryer,then remove the front bottom panel. With your 5/16 nut driver reach to the rear of the vent tube under the dryer and remove the lone screw that holds the tube in place. Lean the dryer forward and remove the tube from the rear of the dryer,this will allow you to see and reach the idler wheel from the front. Release the belt,feel for the clip that holds the wheel in place on the opposite side of the front,with your thumb nail or something else if preferred pry out on one side of the clip until it pops off. Slide the wheel off being careful not to lose the washer,slide the new wheel on and replace the clip. Put the belt back on replace the tube,which is actually the toughest part because you have to find the hole for the lone screw as you can't see it,but with a little patience it is easily enough done. Put the vent hose back on replace the front panel and plug it in and go!!it took me 30 min. Alittle tough to feel for some of the parts,but really much easier than you would think.

Unplug Dryer. Remove 2 5/16in hex screws fm lower panel,3 51/6in hex screws to vent duct. Remove 2 1/4in hex screws to thermostat. Remove 7 1/4in hex screws to blower cover and 2 5/16in hex screws holding base footings.Use adj. wrench to hold rear nut on motor shaft, use7/8in socket to remove fan frm motor shaft. Remove 3 5/16in hex screws holding fan housing to motor mount. Lift-up on spring tensioned belt pulley to remove belt. Pull motor & mount out [wires are layed toward front allowing removal]. Use 6in flat tip screwdriver to unsnap both front/rear motor clamps.Pinch plastic end clamps and remove motor electrical connector.Motor installation is reverse. For belt removal,remove 2 5/16in hex screws to door panel [unhook 2 wires to upper RT rear to door switch].Remove 4 5/16in hex screws to front bulkhead panel.Allow drum to sag IN PLACE [removal not required to replace belt],note belt location and slide old belt off and new one on
Replace Bulheald and door panel [re-attach door switch wires].Complete install by lifting belt pulley and feeding new belt into place. Hand rotate drum to ensure proper belt allignment and tracking. Replace lower panel. Vacuum interior as necessary. Parts delivered in 3days and fit perfectly.

I guessed that this was the part needed.............wrong! Changing it out was easy but the dryer does not work any better. I took the back off of the top of the dryer, unhooked the part, pulled the dial off the front and removed it. Put the new one in and put it all back together. No problem other than my guess! The part was great and I got it in an extremely timely manner.

The repair looked simple enough until it came time to take the out wheel off. Because you can not hold the motor shaft(and the wheel screws on) it was necessary to remove the whole motor assembly and then grind the out shaft down, then use a small screwdriver to take the remaining shaft off.
I must say it was nice to recieve the part in as fast as I did we live in a very rural area and things like that are very hard to find

Being my lousy Maytag washer died THE PREVIOUS DAY, spewing water, etc. and I had rushed out and bought a new washer, I was determined not to replace the dryer (though I now am a serious NON_FAN of Maytag).

I disassembled the whole dryer and finally got to the blower wheel which was broken lose from the molded nut. I supposed something like a dime or penny got in there to shred it.

PartSelect's website allowed me to find the part in 5 minutes. It was on my doorstep the next afternoon.

Installation was straightforward BECAUSE I stacked all the screws and and labeled them appropriately. It took about 30 minutes to reassemble and the toughest bit was getting the drum in with the belt positioned properly.

Used spackle knife to pop clips on top of dryer. Raised lid of dryer to expose belt. Next used nut driver to disassembly screws from front door and then base ( bag them. Labeled bag and marked inside of dryer with corresponding number to match hardware) disassembled dryer door latch switch and marked red + and white no marking. ( Middle connection not used) removed dryer clean out screen and then removed dryer face next removed dryer blower cover no hardware ( just lift upwards see side clips) opened up side of dryer to gain more access (spread apart manually) removed belt and marked where belt was on tumbler postion with permanent marker used 2 car hold down cords to hold drum in place with back of dryer next removed belt from idler (note to make a drawing so that you know how to wrap this around the idler otherwise the belt will appear to be too large. Remember to reconnect spring. Next step was to removed drum rollers. . . This required a retaining ring pliers cost about $15. I replaced the snap retaining rings. This was easy but requires that you pull the drum forward about 4 inches to position. Next replaced belt and reassembled. Project was a success and runs like new. . . . Saved me $129 service call plus $65 parts without maytag mark-up plus additional labor for the job $130. My cost $65 + $15 tool (retaining ring pliers) $80 versus $259 + ( $65 *50%)ark up on parts) $80 versus $356 -- thanks parts select for saving me $276 during the christmas holiday.

First of all I would not have done this if it wasn't for
your website. Using the schematics to figure out
the right parts was easy. It was also helpful in the
actual repair process. I have added your website
to my favorites in my browser. The parts arrived in 3 days and I live in Reno. Great Website.

M.B.

Used a dolly to move the drier out in the garage to give myself some room to work...remove the bottom panel--2 screws at the bottom...remove the door--2 screws at the bottom of the door, disconnect the 2 switch wires and then it slips out of the top....remove 2 screws from the top and swing the top all the way back out of the way---it'll just hang there.....remove the front drum support--4 screws.....slide the drum forward while working the drive belt off of the drum.....you can now see the 2 drum support wheels.....at that time I got my shop vac and got all the lint and crud outa there......remove the snap ring on each wheel, slide off the washer and wheel, pay attention--the wheel has a front and back.....reinstall the new wheel with washer and snap ring (i put a small dab of grease on the wheel support)....I also put a dab of grease on the belt tensioner wheel support--same little snap ring retainer.....reinstall the drum by sliding it in slowly as you work the belt back into place....install the front drum support--roll the drum by hand to make sure your belt is on properly.... resecure the top, then the door, and finally the bottom....when facing the drier my left wheel was in way worse condition----this is obviously because it is located right in front of the heating element....thanx and good luck....

The dryer was squealing, so I looked videos on how to take the dryer apart. After I got it apart, I spun the roller wheels, the motor, and the idler pulley, and only the idler pulley gave an indication that it was sticking or not spinning appropriately, so I ordered the part and replaced it. And sure enough, it was the problem after all!

Disconnect power. First, remove the lower front panel, then the upper front panel (disconnect door switch wiring). Remove two screws holding the top panel to the left and right side panels. Remove wiring connections to light and humidity sensor. Remove four screws to front drum support assembly, lift up to disengage tangs, and remove assembly. Reach in and find the idler assembly for the drum drive belt, and unwrap the belt to loosen it, also removing the belt from the motor pulley.. Slide the drum out the front of the dryer along with the drive belt. Remove the snap ring (using snap ring pliers) and washer holding the idler pulley on to the idler assembly. Remove the idler pulley. Polish the shaft with fine steel wool to get rid of dirt. Clean thoroughly, leaving no steel wool residue. Install replacement pulley, washer, and snap ring. Reinstall drum, taking care to feed belt back into place as the drum is reinstalled. Reach in and wrap the belt around the motor pulley and the idler pulley. Reinstall the front drum support by lifting the drum slightly to allow the support to engage with the drum, and then drop it down to re-engage the tabs into the left and right side panels while reseating it into the blower intake. Install the four screws to hold it in place, and reinstall the wiring for the light and the humidity sensor. Attach the top panel to the left and right side panels with one screw for each side. Reinstall the upper front panel, including reattaching the wiring to the door switch, with two screws. Finally, reinstall the lower front panel. Reconnect to the power source, and you should be good to go.

It was pretty simple, really. Quite honestly, Parts Select was the first website that had my model number listed, and even had a diagram of the dryer. Once I removed the covers, it was very obvious that the belt tension pulley was bad, One side was worn away. I ordered both parts, the new pully, and the tension arm with the bearing, since I had no way to tell which was damaged, causing them to bind. They simply bolted to the motor assembly. The hardest part was reassembly. Getting the front panel on and being sure that the tabs holding it in allignment, and that the drum spun freely was really the only concern. The repair took less than 1 hour, and after seeing the inside of my dryer, I am convinced I can easily replace ANY part of this appliance and keep it running as long as I can find parts.

showed starting withe removal of the dryer top. With my dryer, I needed to start by removing the bottom front panel (2 screws). Next the door panel (2 screws). Now I could remove the top panel (2 screws). From here, the tear down went like the directions th My biggest problems were, figuring out I didn't start with the dryer top. Then getting a proper sized snap ring pliers to remove the drum rollers and and the idler pulley.