LE7111LM (PLE7111LM) Amana Dryer - Instructions

Unplug Dryer. Remove 2 5/16in hex screws fm lower panel,3 51/6in hex screws to vent duct. Remove 2 1/4in hex screws to thermostat. Remove 7 1/4in hex screws to blower cover and 2 5/16in hex screws holding base footings.Use adj. wrench to hold rear nut on motor shaft, use7/8in socket to remove fan frm motor shaft. Remove 3 5/16in hex screws holding fan housing to motor mount. Lift-up on spring tensioned belt pulley to remove belt. Pull motor & mount out [wires are layed toward front allowing removal]. Use 6in flat tip screwdriver to unsnap both front/rear motor clamps.Pinch plastic end clamps and remove motor electrical connector.Motor installation is reverse. For belt removal,remove 2 5/16in hex screws to door panel [unhook 2 wires to upper RT rear to door switch].Remove 4 5/16in hex screws to front bulkhead panel.Allow drum to sag IN PLACE [removal not required to replace belt],note belt location and slide old belt off and new one on
Replace Bulheald and door panel [re-attach door switch wires].Complete install by lifting belt pulley and feeding new belt into place. Hand rotate drum to ensure proper belt allignment and tracking. Replace lower panel. Vacuum interior as necessary. Parts delivered in 3days and fit perfectly.

Make sure to unplug the power cord.Pry the front,top of the dryer up with a screw driver. Carefully disconnect 3 wires and remember where they go, top right. Remove 1 top bolt on each side of the front cover, inside.Pull up slightly and towards towards you to remove the front cover. Disconnect the light wires if applicable and remember where they go from the front drum support. Remove 4 bolts on the front drum mount cover; the lint catcher will come off with it. If needed, pull up and towards you on the drum to lower the it off of the guide rollers to allow slack in the belt. Reach under the drum, raise the idler lever, slide belt from under the idler lever pulley, remove the belt from the the motor shaft. Carefully remove the drum. A 7/16 wrench and ratchet can be used to remove the idler lever from the mount. Remove idler lever from the spring. Reverse these steps for installation of the new idler lever. For installing the belt, actually fold the belt and put it under the idler pulley and back onto the motor shaft. The idler lever should sit on top of the belt when on properly. Make sure the belt is lined with the wear area of the dryer drum. Roll the drum manually, counter clockwise several times to help insure belt alignment before reconnecting the wires and re-installing the front cover and top. A belt replacement will not require removal of the drum.

Well first of all you get to the back of the dryer from the FRONT.. after lower panel was removed location of the heating element was right in front of you. Two 7/16 sheet metal screws hold the heating element in place very easy to remove.. upon removal you will have plenty of room to pull element out and switch out the wires you need to do.. Upon examination I think my trouble was a high limit fuse that burned out, so I propably did'nt need to buy the whole element ( you might want to check that first it is the ceramic one ) cleaned everything out and dryer is as good as new Good luck

I pretty much followed a lot of the earlier postings on partselect.com that provided encouragement to pursue replacing this part on my 17 year old dryer (sorry, money is tight these days and I prefer repair to $800 replacement).

I'd like to add that I borrowed a pair of snap-ring pliers from work which made removal and later securing of roller onto shaft much easier and probably avoided a lot of knuckle bruising and cursing.

I erred though in a couple of places during the replacement. Disassembly took about 20 minutes. However, when I re-assembled I had mistakenly already put the roller onto the shaft before trying to put the drum back in. That isn't possible so I had to remove (an initial groan but only a few extra minutes in the end) the roller from the shaft, then reposition the drum and then the roller back on the shaft.

I also decided to replace the belt while I was in there and I should have taken a picture or made a drawing of the belt route before I took it off since I was later left pondering how the heck to snake the belt onto the shaft and also the tensioner. A quick trip to the internet though showed me a similar route and reminded me how to route it.

I'd also like to add to be cognizant of the wires on the door and front panel when disassembling.

Anyone with any sense of mechanical ability and a little common sense ought to be able to do this repiar.

Thanks Part Select!

The repair looked simple enough until it came time to take the out wheel off. Because you can not hold the motor shaft(and the wheel screws on) it was necessary to remove the whole motor assembly and then grind the out shaft down, then use a small screwdriver to take the remaining shaft off.
I must say it was nice to recieve the part in as fast as I did we live in a very rural area and things like that are very hard to find

First of all I would not have done this if it wasn't for
your website. Using the schematics to figure out
the right parts was easy. It was also helpful in the
actual repair process. I have added your website
to my favorites in my browser. The parts arrived in 3 days and I live in Reno. Great Website.

M.B.

How to take apart a dryer:
The first way:
1) Remove front lower panel (2 screws on bottom).
2) Remove the front black plastic air duct.
3) If you have long arms, or an extention socket wrench, you might be able to reach the heating unit, otherwise use the Second way:

The second way:
1) Remove front lower panel, as this will expose the screws to the dry door unit.
2) Remove dryer door unit (2 screws on bottom, 2 spring clips on top), and disconnect assoc wires.
3) Remove dryer lid:
3.1) Remove 2 screws on front (previously hidden by door unit
3.2) Remove 2 clip hooks on back of dryer
3.3) Lift lid rear above center guides, and wiggle away from front spring clips
4) Lay dryer on back, as this will allow easier removal of the drum
5) Remove screws securing the heater control unit.

Attempt 1: Disconnected heating element and saw that the heating coils were broken. Ordered new heating coil and new belt.
Attempt 2: 3 weeks after installing new heating element, my wife informed me that the unit was no longer putting out heat!!! So, I ordered the Thermostat and Thermal Fuse. Put dryer back together.
Attempt 3: Turned it on - absolutely nothing - dead, dead, dead. Discussed purchasing new $600+ dryer. Started taking it apart again, and discovered that door wire was never reattached. Meaning the dryer thought the door was wide open.
Attempt 4: Now the dryer squeaks. Took dryer partially apart and added white grease to wheels that support the drum. Currently, all is well with the world.

Moral of the story: Replace the entire heating unit, check belt for cracks and grease the wheels if you get a chance.

Used spackle knife to pop clips on top of dryer. Raised lid of dryer to expose belt. Next used nut driver to disassembly screws from front door and then base ( bag them. Labeled bag and marked inside of dryer with corresponding number to match hardware) disassembled dryer door latch switch and marked red + and white no marking. ( Middle connection not used) removed dryer clean out screen and then removed dryer face next removed dryer blower cover no hardware ( just lift upwards see side clips) opened up side of dryer to gain more access (spread apart manually) removed belt and marked where belt was on tumbler postion with permanent marker used 2 car hold down cords to hold drum in place with back of dryer next removed belt from idler (note to make a drawing so that you know how to wrap this around the idler otherwise the belt will appear to be too large. Remember to reconnect spring. Next step was to removed drum rollers. . . This required a retaining ring pliers cost about $15. I replaced the snap retaining rings. This was easy but requires that you pull the drum forward about 4 inches to position. Next replaced belt and reassembled. Project was a success and runs like new. . . . Saved me $129 service call plus $65 parts without maytag mark-up plus additional labor for the job $130. My cost $65 + $15 tool (retaining ring pliers) $80 versus $259 + ( $65 *50%)ark up on parts) $80 versus $356 -- thanks parts select for saving me $276 during the christmas holiday.

Being my lousy Maytag washer died THE PREVIOUS DAY, spewing water, etc. and I had rushed out and bought a new washer, I was determined not to replace the dryer (though I now am a serious NON_FAN of Maytag).

I disassembled the whole dryer and finally got to the blower wheel which was broken lose from the molded nut. I supposed something like a dime or penny got in there to shred it.

PartSelect's website allowed me to find the part in 5 minutes. It was on my doorstep the next afternoon.

Installation was straightforward BECAUSE I stacked all the screws and and labeled them appropriately. It took about 30 minutes to reassemble and the toughest bit was getting the drum in with the belt positioned properly.

Removed the bottom panel. Removed door to dryer and disconnected the door switch. Removed the top of the dryer. Now I had access to the drum basket of the dryer. Removed the belt and took drum out. The idler was accessible and easy to replace. I replaced the other drum support rollers. These were a bit difficult when it came to removing the clamp pins holding the rollers. Once you get one the other is easy. Reassembly is relatively easy and quick. Dryer no longer squeals, runs nice. I felt really good.

I first removed the front panel and door on the dryer using a 5/16th nut driver. I needed to disconnect the light and switch to remove the door. I raised the top lid of the dryer to expose the drum. I rmover the fan schroud and lint filter by removing 4 5/16 screws with the nut driver. I disconnected the belt from the idle tension pully and removed the drum. The drum support rollers were visible on the back frame of the dryer. I removed the bad roller using snap ring pliers. After cleaning the roller support shaft and lubricating the shaft with grease I replaced the drum support roller and secured it with the snap ring. I also replaced the dryer belt although it was still workiing. I reasembled the dryer after giving the inside a cleaning with the shop vac. The hardest part was getting the belt secured with the tension idle pulley. When assemblying the fan schroud make sure it is snug against the fan so it doesn't leak. Replace the top and front door and cover connecting the switch and light. If you get the switch wires correct the dryer will run with the door shut otherwise reverse the wires.

The Dryer is about 25-30 years old. I replaced the motor due to overheating, while I had the dryer disassembled I decided to change out the idler pully wheel and the drum support rollers. This was my first time changing out the motor. Surprisingly, the blowerfan blade came off the shaft of the motor very easy. I was concerned about the age of the dryer and was anticiapating this could be a problem fortunately, it came off very easy. Removing the old motor was easy. The only issue I had was seating the new motor in the correct position. I felt that the motor was not in the correct posiotion however, I was not sure being that this was my first install.
After trying several times, rotaing the motor back and forth (side to side) within the motor holding end brackets the motor fell into place and I was able to put on the end motor clamps on correctly. The drying is now working.

This dryer is an older one. I have kept it running throughout the years by just replacing parts a needed. This was a kind of rebuild. The dryer was making that squeaking noise when running so I knew the "glides" were worn and the belt, rollers and idler pulley had never been replaced. I ordered the parts from this website and I must say it took a while for them to ship, of course I guess since it was during the holidays that's to be expected. Once I received the parts I took the dryer apart. This model has a lower panel that comes off first then there are two 5/16" sheet metal screws that hold the door panel in place and then two more to hold the top down. Then I removed the front bulkhead which holds the drum glides. I replaced the glides then removed the drum from the dryer. To removed the motor there are two 5/16" screws to removed then pull the motor from the bottom. I then replaced the idler pulley, the two drum rollers on the rear of the dryer and the belt on the drum. Reassembly went fairly easy. I found the door switch was bad during reassembly because the dryer would not shut off once the door was opened. So picked up a new door switch from a local supplier, replaced it and all is good now. There really isn't that much to a dryer. A motor, heating unit (in the rear), control unit/timer on top, and then the rollers, idler pulley, and drum belt. The video instructions on this website were quite helpful. Hopefully it will last another year.

Viewed video on website, however did not match model but put me in the ball park for an overall view. Thank goodness I had the insight to order the pully with the belt. I believe the pully failed first causing the problem with the belt. Recommend replacing both any way while you have it apart.

After checking out a video showing how to change the belt I decided to tackle the job. First I pried up the top, there are two plastic tabs in the front corners that hold the top down to the front panel. The top swings upward and will stay in position while you continue to work. Using a 3/8 socket, I removed 4 bolts that hold the front panel onto the frame. Be sure to unhitched the wiring to the door switch and those to the control panel and then the front will come out by lifting it off the tabs in the lower corners. Put the front panel aside and slide the drum forward and out of the dryer frame. Remove the old belt noting how it ms oriented around the tensioner and motor pulley. Now everything should be exposed and you should take the time and clean the inside if I were you. Our dryer was filled with lint and dust but after a good vacuuming and wiping down with a damp sponge, it looked like new again. Put the new belt around the drum noting where it had sat before. There is a grove in the drum but our belt did not go inside their but on the drum itself. Slide the drum back in place and from underneath put the belt on the pulley and under the tensioner. Replace the front panel, rehitch the wires and put the top down and your done. My wife helped clean the inside which took longer than replacing the belt. Total time about an hour or so cleaning time included.