AGM659 Amana Dryer - Instructions

Removed lower panel, door assembly, belt and drum.
Removed blower wheel cover.
Used dremmel tool to cut plastic from metal that attaches the blower to the motor shaft.
Used adjustable wrench to keep motor shaft from turning.
Used vise grip to clamp on metal and turned to loosen blower wheel.
Attached new blower and re-assembled.

took frount off ,then filter, pulled drum out, then blower plate & spun impeller off. went back together easy ,except belt . that gave me a little problem but finally got it thanks

I first unpluged the dryer. Then I
Removed two screws and removed bottom cover, Then removed the door assembly.Here I had to unplug the light and door switches. I then removed the four screws that holds the tub mount in place, Then I removed the eight screws that hold the blower cover in place, then removed the blower. replaced blower and reassembled in reverse. I started the dryer and it worked fine.

Thanks to reports from others, I concluded that most likely the gas ignition coils (one or both) were no longer functioning properly. I replaced both with the 'M' Series New Style Coil Kit which is about 1/2 the price of either coil individually -- yes,true,go figure! The actual replacement took only about 10 minutes. What was most difficult and took the most time was the removal of the front panel of the cabinet -- this was difficult only because there were no instructions in my owner's manual (or any other source I could find) and it took me awhile to figure it out. Now I could do the whole job in about 20 minutes! The detailed instructions from others as to the process of replacing the coils was invaluable -- I don't know if I would have been able to figure that out on my own. But most important was the information that enabled me to diagnose the problem in the first place. Thank you, all you previous comment contributors.

unplug appliance.removed 2 screws @ the rear of dryer top to tip lid back. unplugged the door switch wires.took out 3 philip screws that hold lint screen to inside of drum.removed 2 screws @ dryer front top. lifted dryer front panel off. the drum was now loose. slipped off old belt - replaced with new. set drum back into place. made sure new belt was on motor pulley & behind tensioner pulley arm. replace & reconnect items in reverse order. plug back in & test. after seeing the wear on the plastic tensioner pulley i regret not ordering that part for replacement also.

easy even for an old man. Simply removed igniter bracket inside access door on the front and installed new part. Flex drive nut driver and 1/4" socket was all that was needed. Saved me a lot of money and time without the 25 year old dryer.

Checked out the coil seemed ok. So I replaced the radiant flame sensor. No change. Then I replaced the High limit sensor still the heat was not staying on. I read some were in the troubleshooting guide that the coil can test good, but can still malfunction. So that was it new coil fix it, works like a new Dryer again.

Dryer stopped tumbling, so bad belt was my first thought. Dryer is in vacation home so did not have immediate access to it to diagnose. Ordered belt and discovered that the poorly designed motor pulley had broken and the belt jumped onto the motor shaft and burned through the original belt. Week 2 after ordering pulley, installation went per YouTube video. Glad I also replaced the belt because it was brittle and cracked. Suspect it had been slipping because sheets would ball up into a log, possibly because the drum wasn't spinning fast enough. Anyhoo, after repair all seems OK.

I watched the repair video and followed the instruction given to replace the belt. The instructions were easy to follow and to the point. The one thing that was not covered was to vacuum the interior prior to closing the dryer up.

After watching the great install video, I followed his lead and within 20 min had my dryer door fixed. This dryer was bought in 1986 and I really thought I was looking at buying a new dryer. How wonderful that I could fix it for less than $11. Easy to find web site, easy to find part, great instructions and fast delivery!

I guessed that this was the part needed.............wrong! Changing it out was easy but the dryer does not work any better. I took the back off of the top of the dryer, unhooked the part, pulled the dial off the front and removed it. Put the new one in and put it all back together. No problem other than my guess! The part was great and I got it in an extremely timely manner.

Very simple repair. Remove front panel, door, drum etc. Try to keep everything seperated, screws etc. I put lockjaws on the back to get the nut off the front. Make sure to check the housing for "melted on" blower wheel residue. Easy enough to remove. I checked with my local parts dealer he wanted twice the price and needed to order it (at least a days wait). PartSelect sent the exact same part in a day and a half. Put everything back the same way I removed. Hardest part is the drum and belt. While you have everything apart don't forget to clean the thermastats etc. PartsSelect was quicker and cheaper.

Removed two screws on lower front dryer panel with 5/16" socket and wrench. Removed three screws and plastic filter dryer screen vent with 1/4" socket allowing easy access to upper limit thermostat switch located on side of igniter flame assembly tunnel. Removed two screws attaching limit switch and disconnected two wires. Replaced with new limit switch and reconnected wires. Reassembled dryer. Works fine. Drying time for regular items such as towels is now less than 1 hour.

First unplug the dryer,then remove the front bottom panel. With your 5/16 nut driver reach to the rear of the vent tube under the dryer and remove the lone screw that holds the tube in place. Lean the dryer forward and remove the tube from the rear of the dryer,this will allow you to see and reach the idler wheel from the front. Release the belt,feel for the clip that holds the wheel in place on the opposite side of the front,with your thumb nail or something else if preferred pry out on one side of the clip until it pops off. Slide the wheel off being careful not to lose the washer,slide the new wheel on and replace the clip. Put the belt back on replace the tube,which is actually the toughest part because you have to find the hole for the lone screw as you can't see it,but with a little patience it is easily enough done. Put the vent hose back on replace the front panel and plug it in and go!!it took me 30 min. Alittle tough to feel for some of the parts,but really much easier than you would think.

The repair looked simple enough until it came time to take the out wheel off. Because you can not hold the motor shaft(and the wheel screws on) it was necessary to remove the whole motor assembly and then grind the out shaft down, then use a small screwdriver to take the remaining shaft off.
I must say it was nice to recieve the part in as fast as I did we live in a very rural area and things like that are very hard to find