ALG866SAW (PALG866SAW) Amana Dryer - Instructions

unplug appliance.removed 2 screws @ the rear of dryer top to tip lid back. unplugged the door switch wires.took out 3 philip screws that hold lint screen to inside of drum.removed 2 screws @ dryer front top. lifted dryer front panel off. the drum was now loose. slipped off old belt - replaced with new. set drum back into place. made sure new belt was on motor pulley & behind tensioner pulley arm. replace & reconnect items in reverse order. plug back in & test. after seeing the wear on the plastic tensioner pulley i regret not ordering that part for replacement also.

I had already taken the dryer apart prior to changing the felt seal. Had oiled the rollers, greased the bearings & vacuumed the whole inside of the dryer out. Had used a high temp lubricant on the seal & had stopped squeaking for about a month. I ordered 2 seals & when they arrived, I popped the top of the dryer off using the putty knife to pry the spring latches. I opened the top up & leaned it against a wall. I disconnected the wiring to the light & the switch in the door, making note of the wiring order. Then used a nut driver to take the 2 screws from the inside out, that holds the front cover in place. Then the same for the 4 screws holding the front bulkhead in place. Then lifted up & out from the unit. Then used the putty knife to scrap the adhesive & old seal off the bulkhead. Cleaned as much of the adhesive off, then applied some high temp silicone adhesive to the bulkhead, placed the new seal on, using some clamps to hold it in place. After making sure it had adhered to the seal & bulkhead. Did the reversal of the above mentioned steps. Moved the unit to laundry room, plugged it in then started it & voila no more squeaking dryer.

Dryer stopped tumbling, so bad belt was my first thought. Dryer is in vacation home so did not have immediate access to it to diagnose. Ordered belt and discovered that the poorly designed motor pulley had broken and the belt jumped onto the motor shaft and burned through the original belt. Week 2 after ordering pulley, installation went per YouTube video. Glad I also replaced the belt because it was brittle and cracked. Suspect it had been slipping because sheets would ball up into a log, possibly because the drum wasn't spinning fast enough. Anyhoo, after repair all seems OK.

Removed lower panel, door assembly, belt and drum.
Removed blower wheel cover.
Used dremmel tool to cut plastic from metal that attaches the blower to the motor shaft.
Used adjustable wrench to keep motor shaft from turning.
Used vise grip to clamp on metal and turned to loosen blower wheel.
Attached new blower and re-assembled.

remove bottom two screws on lower front panel, remove panel. remove two screws on lower portion of door panel, pull bottom panel towards yourself to release pins at the top. Disconnect wiring for light and door switch (make sure to note what wires go where. Complete removal of front door panel. Remove 4 screws holding cylinder frame in place, lift to remove. remove remnants of old felt seal, use rotary tool to remove excess glue, etc. apply glue (used rubberized gorilla super glue), apply felt seal - allow glue to set up. reinstall in reverse direction from removal. Be sure to use glue as there are no clips or other retaining pieces for the new felt and it will not hold in place. overall pretty easy.

Removed the two nuts at the bottom of the dryer front to be able to move the front piece. Removed three screws holding the vent assembly in place. Removed vent assembly, replaced with new part and replaced screws and nuts.

Early in the life of my dryer, the Cylinder Seal came out. For the past two years I put off buying the part. When it came in, I p[opped the top of the dryer, removed the two screws holding on the front panel, and pulled the Cylinder of the back wall of the dryer. I then placed the seal in the right spot, glued it down and reassembled. About Fifteen minutes of work and a cheap part, and now my dryer dries a l;oad of clothes in an hour instead of three.

After removing the front panel, the igniter just just snaps into the bracket.

Being my lousy Maytag washer died THE PREVIOUS DAY, spewing water, etc. and I had rushed out and bought a new washer, I was determined not to replace the dryer (though I now am a serious NON_FAN of Maytag).

I disassembled the whole dryer and finally got to the blower wheel which was broken lose from the molded nut. I supposed something like a dime or penny got in there to shred it.

PartSelect's website allowed me to find the part in 5 minutes. It was on my doorstep the next afternoon.

Installation was straightforward BECAUSE I stacked all the screws and and labeled them appropriately. It took about 30 minutes to reassemble and the toughest bit was getting the drum in with the belt positioned properly.

I took out the old worn out part and replaced with the one I order.

discovered it was a broken latch. Ordered the latch, only took 2 days to arrive and all I had to do was remove the broken latch and snap in the new one. I saved myself a service call. I'm very happy!!!!!!

Removed power and front panel, removed broken latch, pushed in new latch and replaced the front panel and power. Done

No problem

Ordered the part, you made it so easy. Received it in two days, very fast, by regular mail. Perfect fit. Pulled out the old broken one and put in the new one!

removed the bottom panel. then the door. unscrewed the 4 screws, removed duct and replaced. parts came fast and fit just right! no issues at all! I recomend Parts select as an appliance vendor for parts.