LEA30AL (PLEA30AL) Amana Dryer - Instructions

Took dryer apart, and found that the idler arm pulley was in pieces. Ordered the replacement from Partselect.com. Received part very promptly. Decided to also order a new belt, and that arrived in a very timely manner also. Put the parts in, and assembled the dryer. This was for my 90 year old grandmother, and she is ever so pleased that it is up and running again. Completed the repairs for about $50, and saved big money by doing it myself versus a service call, that would have boiled down to replacing the unit for the price it would have cost to fix. Will use partselect in the future for all my appliance repairs, as they offer a great selection of parts for all different appliances. Very pleased with satisfied with quality, and service from Partselect.com

I went to RepairClinic.com & FixYa.com for some great advice. I searched the internet for the parts. PartSelect.com was the most inexpensive. Delivery was good. Using the repairman's manual I found on the internet I followed the steps to remove each panel, in order. The wiring was the most bothersome, but okay to resolve; write it down and pull it off! I don't think the rollers, in the back, were bad. The tension idler was extremely worn. I tightened the tension idler bracket at the base. I did need to use an O-Ring Spreader to get all the rollers off and on. Although there were more panels to remove than older models, it was easier! Wrap the belt around the drum before reinstalling. The belt will loop around the drive & tensioner relatively easy. Replace the rubber seal around the drum & replace all the panels. Things are quieter now than I can remember in a long time.

I watched the repair video and followed the instruction given to replace the belt. The instructions were easy to follow and to the point. The one thing that was not covered was to vacuum the interior prior to closing the dryer up.

Replaced the two drum rollers and the tensioning arm roller. NOTES: 1. There are two drum rollers, the diagram seems to show only one. Recommend replacing both drum rollers and the support bracket shaft assemblies since the shafts might be scored. 2. The tensioning arm roller was actually much worse and frozen, so once you are in it is best to replace ALL three rollers. 3. I also replaced the belt since it was worse for wear from the frozen rollers. 4. The PartSelect video for the procedure is for the Whirlpool branded version of this dryer. The internal parts and construction are identical, however, the initial steps for opening up the dryer are different. On the Amana the top also tilts up, but is held down by two bolts, and not just the spring clips. Steps are: a) Remove bottom kick plate which is held in by two bolts on the lower front edge. b) remove the retention bolts that are now exposed on the front panel and remove the front panel by pulling it down from the top spring clips. c) Unbolt and remove the front drum retention panel. d) The two bolts that hold down the top can now be removed and the top panel tilted up so the drum can be lifted out after the belt is loosened. The whole process is very quick and easy. Only tricky part is fumbling around behind the motor to move the tensioning roller and arm to remove and re-install the belt. Also, I had cheap spring clip pliers so I was fumbling with the spring clips that hold the rollers on their shafts.

Removed bottom panel, lint vent assembly, door assembly, removed belt, drum, then heating element from back panel. Unplugged wires from heating element and put them on new element in same order screwed the element back in then all the steps in reverse order. Now I have heat when I run the dryer.
Partselect was extremely fast in shipping my order. I will shop here again!

watched video for Each Part

Removed lower front panel.

Removed door assembly* making note of the wire positions on the door switch
* When removing the door assembly DO NOT LET IT DROP DOWN! Doing so will destroy the door switch. Swing the door assembly upward from the bottom toward you as high as it will go then pull it free.

Removed the drum and belt assembly.

Removed the idler pulley and idler pully spring.

Vacuumed up the interior dryer floor and blew out the motor w/ comp air. Also cleaned the ribbed motor pulley with a nylon brush and brake cleaner sprayed on a shop towel.

Removed the drum tires and cleaned their shafts and internal bearing sleeves with brake cleaner sprayed on a shop towel.

Reinstalled the drum tires after lubricating their shafts with a very light coat of general purpose grease.

Replaced the idler pulley and idler pulley spring after cleaning and lubing shaft and pulley bearing as done on the drum tires.

Reinstalled the drum with the new belt (ribbed side down) roughly in place.

Reinstalled the front door assembly after reconnecting it's wiring making sure to insert it's top locking tabs with the bottom of the door held up high then swung down into place

Tensioned the belt by positioning the flat side of the belt that comes down the right side of the drum over the idler pulley flat side down and then the ribbed side of the belt over the motor shaft. You will have to move the idler pulley arm to apply full tension against the spring in order to have the slack to get it around the motor shaft.

Reinstalled the lower front panel.

Checked dryer operation OK.

This repair was rated a bit difficult because I didn't know the trick for removing/installing the door assembly and destroyed the switch. Furthermore, putting the belt back on is a somewhat difficult challenge because you have to do it mostly by feel

Door switch was very easy to replace as it simply snaps in for the outside and you just clip on the two control wires that already have clips on them.

There was no repair, just replacing the old, wornout lint filter. But I wanted to thank you for the ease in finding the part and for your prompt delivery. I really appreciate that. If we need any other parts we will order them from you.
Thanks again!

My repair was very easy, the lint trap just comes assembled like when you buy the dryer. However, I had a hard time finding the dryer part at a store.
Part select had the item, they made it really easy to find online. The best part is how fast I received it! My dryer broke the day before thanksgiving (wednesday) i ordered the part that night and had it saturday morning! and thats with thursday being thanksgiving! I didnt even the pay extra for faster shipping! I would use them again and recommend them!

All you need for a Maytag is a snub nose Philips screw driver. The screws on the front panel are at the bottom angled down, so a regular length Phillip's won't work. Just unscrew the 2 screws, then lift the panel up and out. Careful not to pull out too far, there are 2 wires attached to the switch. The replacement switch is NOT an exact copy of the old one. My Maytag is over 30 years old and it only had 2 prongs on the switch. The new one has 3. Don't let that throw you. It is the same size. Just attach, 1 wire to the bronze connector & the other to the silver. Push the switch into the door opening, re-attach the door. Total time 20 minutes. Saved well over $100 in a service call. Anyone with an IQ above freezing can do it.

After taken apart to replace high limit thermostat fuse and limit thermostat took about 5 minutes. Also our dryer always ran very hot no matter what setting it was on. Replaced idler pulley wheel also because seemed not to rotate very well. Put all back together and worked perfect. Ran and does not overheat now.

1.Unplug unit
(gas model, did not shut off)
2. Remove bottom front panel-2bolts
3 Remove main front panel-2 bolts (no need to remove door)
4. Make note of wire colors on door switch and light, disconnect
5. Remove 3 screws that hold air duct assembly(that lint filter rests in) then set main front panel aside
6. Remove lower air duct (to blower motor)-3 bolts
7. Lift and tilt-up top lid/panel of dryer and wedge wood or ? (this will give you easy access and better light)
8. Reach back behind motor to move idler pulley and remove belt from motor & idler pulley
9. Remove 4 bolts and lift up and out front bulkhead frame that holds drum in place
10. Slowly pull straight out & slightly up entire drum
11. Remove circlip/retaining ring, washer, roller, washer and shaft assembly.
12. Vacuum entire unit
13. Light lubricant on shaft when reinstall in reverse order.

Snap ring pliers and a mental note of how the belt is routed on idler will prevent unwanted profanity.
This is an inferior/substandard unit before Maytag bought them. Spend the money and replace both rollers with new shafts (about 50.00). I have spent over 140.00 in parts to keep this unit running (less than 8 years old). So do the math before you start pouring money into this model.

Replaced glides and assy idler pulley cleaned all parts fron dust and debree, vaciumed heating eliment to remove all excess lint and wool to make sure I did'nt have a fire in the lower unit.
Job was'nt all that hard just have to watch what you're doing.

Followed the recommended repair under noisy machine, replacing the 3 recommended parts. The 10 minute video was extremely helpful. Important note: there are two(2) drum support rollers. Also, you definitely need very small C ring pliers and don't forget to label all wires before disconnecting.