DLE330RCW Amana Dryer - Instructions

First I unplugged the dryer, then I removed the bottom front panel. Then the door I marked the wires to the shut off switch on the door and removed the switch from the door. Next was the lint screen housing and duct work that goes to it. Then I had to reach under the drum and take the belt off of the motor pully and tensioner so I could remove the drum. I removed the drum. I then marked all the wires I had to disconnect. I took the fan housing front panel off. I held the belt drive end of the motor shaft with the pipe wrench, i could have used an open end or an adjustable wrench also. I used a 7/8 six sided socket on the plastic fan nut on the front of the shaft so that if it was hard to loosen I would have a better chance of not rounding the nut. I removed the fan and the back of the housing, unplugged the motor, and removed it. The clips that hold the motor to the motor bracket are a little tricky, I used a screw driver to remove them. I then replaced the motor and put everything back together. One hint you should know is to make sure you mark the drum front so when you put it back in you get it right the first time. I fits in both ways and will go back together but it won't turn free and you'll have to take it all apart again. I tried it by hand both ways and was able to catch the mistake before I put it all back together, but I could have put it together wrong.

DIAGNOSTICS: Unplug dryer to reset controls. Remove lower cover. Plug back in. Start dryer. If flame starts and goes out in a few seconds, probably the cycling thermostat (located centrally near bottom of dryer) is bad. It fits in the center of the thermostat heater (not replaced). Use the on-line schematic. I reset the controls (as above) again and jumpered the cycling thermostat. This time the flame stayed on. I turned off dryer before High Limit Thermal Fuse could blow out. Only a trained electrician should do the above.
REPAIRS: Decided to remove main cover, to get better angle on thermostat screws. Unplugged. Removed door first. Be gentle with wires. Be careful with drum, it will simply fall out if jarred. Remove two screws for cycling thermostat. Remove wires, replace cycling thermostst. Reassemble. Be sure drum is still on rollers on back and anti-friction strips in front.
SHORTCUT: If you use an articulated socket wrench on the thermostat screws, you can save your self the trouble of removing the front cover, door, and possibly drum.

1. Remove bottom sill plate with two screws
2. Remove door, watch for the wire.
3. Remove tub retaining "ring" 4 screws
4. Pull tub forward
5. Pull off the old support roller using the snapring pliers
6. grease the new roller and pins (do both sides)

Reverse it and put it back together and its good as new!

Just take the old parts with my tools and fix it, i did take the pulley bearing with care and put the new one, and adjust the screw on the motor base, the belt just was a little difficult but I did it, it's easy.

First I removed the bottom front cover attached with two screws, then the main front cover attached with two screws. I then removed two more screws holding the top in place, detached three wires and raised the top lid. I held the top lid out of the way with a cord tied off to a cabinet above. I then removed four screws holding the front support panel in place and set it to the side with wires still attahced. Then I slid the dryer belt off the drum and removed the drum. Next I removed the cover of the fan wheel by removing several screws. This allowed me to unscrew the fan wheel (reverse threaded) by anchoring the motor shaft with a wrench and using a large socket to turn the nut end of the fan wheel (then was no snap ring). I then popped off the two clamps holding the motor in place and removed the motor. The only tricky part about assembly was putting the belt back on the pulleys once the drum was installed. You can't see the pulleys once the drum is installed so it is done by feel.

Removal of the entire 2 front panels
Removal of the heat exchanger into the drum
Removal and replacement of the belt
Reinstallation of the heat exchanger, and both front panels

I looked at your on-line diagrams (exploded views) and basically used them as dis-assembly info.

I removed the bottom panel, followed by the front panel, the drum holders and drum.

Toughest part was the spring clips holding the motor in place,,,, but notes on your site from other folks doing the same motor replacement solved that one,,,,,, I used a flat bladed screwdriver and pliers to manipulate the clips both off and on

Ordered the new heater element on Saturday and got it on Tuesday. I have ordered from PartSelect before and the service has always been fast and accurate.

The first thing I did was to unplug the dryer and then removed the bottom front pannel by removing two hex screws, one on each side near the bottom of the dryer. Use a flashlight if you need to see better. I then used my shopvac to vacuum all the lint that had gathered over the years, including the old heater element located on the left side towards the back bottom part of the dryer. Located the two hex screws and unscrewed them to remove the heater element. Pull out a bit from the bottom and then down. Pull towards you and remove the wiring from the old heater element making sure where the wiring and parts to be reused go so they could be transferred to the new heater element. Re-attach the heater element with two hex screws. Replace front cover and plug in the power cord and start drying clothes.

Removed 2 screws from dryer lower front panel and removed panel. Then removed upper front panel (no screws, just clips). Removed screws from existing duct assembly (2 for the duct assembly and 3 that held the top of the assembly to the dryer opening (and the reason for removing the upper front panel). Original part was a two piece assembly, new one is a single part, using less screws. New part is also deeper that original assembly. There was enough room for the extra size. Installed new part, replaced top 3 screws, top panel, and bottom panel. The replacement was very straight forward. Anyone that has done this before could do it in a few minutes but without prior knowledge or a manual, it took a full 1/2 hour to do the replacement.

Watch the video. Very, very easy

Took off the four screws to get to the female clip and used pliers to squeeze it out. Next was using pliers to pinch out the male connector and place the new one in.

The replacement part just snapped into place. (The old part had fallen out) It took less than 30 seconds to do the repair.

First I put the square female end iof the door catch kit nto the square hole as snug as I could. Then I gently pushed the door against the piece until I heard it click in to place. That's it!! Sooooo simple--

popped up top of dryer -- With pliers squeezed clips on inside of latch - - with screw driver pryed latch out -- just pused new latch in.......... Thanks to parts select for sending part sooo fast.. wife was happy.. Thanks, Dale

Had to figure out how to open the dryer - bottom screws in front and work up, removed the drum and found the fan blade was broken. Had some difficulty removing the fanblade from the motor shaft but after that the new one was easy to install. I did need help to place the belt and drum back into place. as one person has to hold the belts on the pulley while the other adjusts the belt while putting the drum back into place.