LED65AW (PLED65AW) Amana Dryer - Instructions

I went to RepairClinic.com & FixYa.com for some great advice. I searched the internet for the parts. PartSelect.com was the most inexpensive. Delivery was good. Using the repairman's manual I found on the internet I followed the steps to remove each panel, in order. The wiring was the most bothersome, but okay to resolve; write it down and pull it off! I don't think the rollers, in the back, were bad. The tension idler was extremely worn. I tightened the tension idler bracket at the base. I did need to use an O-Ring Spreader to get all the rollers off and on. Although there were more panels to remove than older models, it was easier! Wrap the belt around the drum before reinstalling. The belt will loop around the drive & tensioner relatively easy. Replace the rubber seal around the drum & replace all the panels. Things are quieter now than I can remember in a long time.

I watched the repair video and followed the instruction given to replace the belt. The instructions were easy to follow and to the point. The one thing that was not covered was to vacuum the interior prior to closing the dryer up.

All you need for a Maytag is a snub nose Philips screw driver. The screws on the front panel are at the bottom angled down, so a regular length Phillip's won't work. Just unscrew the 2 screws, then lift the panel up and out. Careful not to pull out too far, there are 2 wires attached to the switch. The replacement switch is NOT an exact copy of the old one. My Maytag is over 30 years old and it only had 2 prongs on the switch. The new one has 3. Don't let that throw you. It is the same size. Just attach, 1 wire to the bronze connector & the other to the silver. Push the switch into the door opening, re-attach the door. Total time 20 minutes. Saved well over $100 in a service call. Anyone with an IQ above freezing can do it.

Took dryer apart, and found that the idler arm pulley was in pieces. Ordered the replacement from Partselect.com. Received part very promptly. Decided to also order a new belt, and that arrived in a very timely manner also. Put the parts in, and assembled the dryer. This was for my 90 year old grandmother, and she is ever so pleased that it is up and running again. Completed the repairs for about $50, and saved big money by doing it myself versus a service call, that would have boiled down to replacing the unit for the price it would have cost to fix. Will use partselect in the future for all my appliance repairs, as they offer a great selection of parts for all different appliances. Very pleased with satisfied with quality, and service from Partselect.com

My repair was very easy, the lint trap just comes assembled like when you buy the dryer. However, I had a hard time finding the dryer part at a store.
Part select had the item, they made it really easy to find online. The best part is how fast I received it! My dryer broke the day before thanksgiving (wednesday) i ordered the part that night and had it saturday morning! and thats with thursday being thanksgiving! I didnt even the pay extra for faster shipping! I would use them again and recommend them!

Door switch was very easy to replace as it simply snaps in for the outside and you just clip on the two control wires that already have clips on them.

There was no repair, just replacing the old, wornout lint filter. But I wanted to thank you for the ease in finding the part and for your prompt delivery. I really appreciate that. If we need any other parts we will order them from you.
Thanks again!

Followed the recommended repair under noisy machine, replacing the 3 recommended parts. The 10 minute video was extremely helpful. Important note: there are two(2) drum support rollers. Also, you definitely need very small C ring pliers and don't forget to label all wires before disconnecting.

Changed, got in aimed wrong direction-best to take a digital photo before you disassemble. Overtightened bolt and nut in assembly, it seized. Attempted to drill/grind it off, should have removed motor. Drill skipped up into motor windings. Could have replaced dryer, decided not, fixed by ordering motor, mount, nut and bolt and new belt idler. Reassembly was a snap till the gremlins hit again and I lost one of the drum glides. After a trip across town, I reassembled and it was good to go. Disassembly, use a screw driver to pry up the top, use the nut driver to remove upper front left and right screws, lift front forward and off bottom hooks. You have to release the wiring harness, it has four connectors. Use a sharpy marker and write the wire colors next to the plug-ins connectors you pull gently off and set the door aside. The second wires are two wires for the inner assembly which again need to be marked for color and then pulled loose. Pull them through the plastic hold down so they're out of the way. Use nut driver to remove four screws from inner drum holder, pry gently off dryer blower. Reaching around both sides of the blower housing find the belt tensioner, pull it to the right, push the belt out of it. Lift the drum out, up slightly over the back rollers. Set aside. Use the nut driver to remove the screws into the base holding the motor mount down, now lift the motor/blower assembly forward and pull gently loose from the dryer vent pipe. Set it up where you can work on it. Using the nut driver, take the screws off the blower housing, use a vise grip to secure the motor and use a 7/8 inch turning counter clockwise to remove the turbine. Use the nut driver to remove the screws holding the turbine housing in place, pop the motor clips off. Pull the motor off and remove the nut and bolt of the belt idler assembly using a wrench on the back and a socket wrench on the other side. Reverse order to reassemble, when tightening the idler arm tighten it to where you feel it stop but not any further. Put the belt around the drum again, get it in the previous location on the drum, feel around the drum to make sure belt isn't twisted, bring belt in from the back between the idler wheel and the vent pipe in a loop (Make sure the belt is behind the tension spring rather than in front), Tip the idler arm upward, use the other hand to slide the belt loop up over the motor pulley. One final note is this being a Maytag you might write these direction on the inside of the front panel for next time.

Per instructions I printed off online: took off door, then the front panel. Pulled out the old switch/button, connected the new switch/button, made sure the new button was working; put the panel back on then the door and DONE!

Once I was able to take apart the door assembly, I was able to determine that I needed the lint duct assembly. The parts website was very helpful with diagrams and explanations so that I could order the part with confidence. Since laundry is so important in our house I paid for expedited shipping. The part arrived in Florida less than 24 hours after it was ordered and soon after it was installed and the dryer was working properly.

took one out - put new one in

I used a large flat head screwdriver to lift top up, then located 2 screws in the top right and left hand side to remove front. Remove the three Phillip Head Screws that holds the assy in place slide out. Mine had 2 metal pieces with wires. I simply unplugged and took metal pieces and installed in the new assy. Remove excess lint put front back on lowered lid and done! 15-20 minutes

Terminal Block was cracked and dryer was not receiving enough voltage, causing the heating element not to heat. Here were the steps I took to fix the problem:
1. Turn off breaker to dryer from 240v outlet
2. Unplug dryer from 240v wall outlet.
3. On outside, rear of dryer, remove cover plate and the clamp that the power cord goes through with nut driver or phillips screwdriver and take picture or write down how the power cord wires go to the terminal block.
4. Use nut driver or phillips screwdriver to remove the power cord wires from terminal block and ground wire from dryer body.
5. On top front of dryer, use large slotted screwdriver or some other tool to push in on the two clips in order to lift the cover up on dryer.
6. Take picture or write down how wires are attached to terminal block.
7. Remove wires from terminal block with nut driver or phillips screwdriver.
8. Use nut driver to remove terminal block from washer and install the new terminal block.
9. Reinstall wires to new terminal block.
10. Close dryer cover.
11. Reinstall clamp onto power cord wires and reinstall wires to new terminal block and ground wire to washer body then put cover plate back on.
12. Plug in dryer then turn on breaker.
13. Start dryer to see if it heats now.

Propped the machine up in the front, removed the front panel, the door assembly, and the front drum support. Use a Sharpie to mark wire positions. This will help during re-assembly. To get the drum out, you first have to remove the belt from the motor pulley. Drum slides right out. You will need snap-ring pliers to remove the pulley from the idler arm. I also replaced the drive belt because it was cheap, and always a good idea to replace it when you are this far into the machine if it is a few years old. Re-assemble in the reverse order of disassembly. An easy fix for the average do-it-yourself person.