Models > TGA600 > Instructions

TGA600 (P7575202W) Amana Dryer - Instructions

Jump to:

All Instructions for the TGA600
121 - 135 of 218
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Joseph from Palos Park, IL
Parts Used:
306436
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
The dryer door would not stay closed.
After 20+ years of service, the plastic part that holds the dryer door closed, broke. I orderd the replacement part on a Monday and received it on Wednesday!
By applying constant pressure with my thumb, the replacement part 'snapped' into place - all of 4 seconds.
Fast delivery of parts and fast instal, made for a great day.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Thomas from Melrose, MA
Parts Used:
LA-1003, 306436
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Door would not stay closed
Repair part just snapped into place. It took longer to open the bag then do the repair. I thought it was going to be difficult to find a part for this dryer but partselect had the right part.
Thanks
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Richard from Rochester, NY
Parts Used:
61927
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Not much heat
Loosened the screws, took out the old one. It shorted out to back. Inserted the new one attached wires, Installed screws and it worked
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ed from Oak Lawn,, IL
Parts Used:
306436
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
broken door latch (receiver)
removed old broken piece with screw driver and pliers...
replaced with new part with thumbs as pushers.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Thomas from Hatboro, PA
Parts Used:
306436
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Door Latch broken
unscrew the screws at bottom front of dryer, lift outward, upward, the bottom of the front of the dryer. As the dryer front tilts outward/upward from the bottom, the area where its hinged at the top of the front will disengage from the main frame of the dryer and the face of the front of the dryer comes off. remove the old door latch by manipulating the plastic body of the latch (wiggle, twist pinch . . .) until, from the back, you can push the old latch forward through the front of the front of the dryer. At this point, you can put the new door latch back in from the front and push it in to place.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Leiykun from Steelton, PA
Parts Used:
306436
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
dryer knob brock off and installed with new
To remove and install the new parts, I followed the video instruction at whirlpool.com. Then removed the old knobs and put the new ones in. The new one created a rough contact and needed a little lithium grease to make a smooth insertion to prevent the friction from damaging the new part. It was an easy fix and took about ten minutes. Good luck in your repairs!
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Orson from Harrisburg, IL
Parts Used:
306436
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
latch broke off; door wouldn't stay closed
I took the two screws out of the end of the door and the door handle off. Then able to part the interior of the door enough to replace the latch. The video was really great.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Luis from Arlington, MA
Parts Used:
LA-1003
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Door wouldn't stay closed
I used a screwdriver to pry out the broken door latch and inserted the new one in the same slot. Perfect fit. The picture of the part in the order page was a big help to identify the correct part.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Pete from Charlotte, NC
Parts Used:
56000
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
no heat ... rattle ... no air through vent
Determined no air flow or heat through system even though dryer spun and timer worked. Ouside vent dispelled no air. Opened dryer panel.
Blower wheel/fan broken off from shaft. Googled appliance parts ... found ... Partselect .... keyed in mfg, model number ... schematics available ... found part ... ordered ... received in two days ... installed ... reassembled. Working fine ! $ 30.00 compared to buying new dryer ! This was a refreshing and rewarding repair. If it could always be this smooth !!! Great resource ... PARTSELECT !
1 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dave from Thorntown, IN
Parts Used:
WPY54414
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Socket set, Wrench set
Idler Pully squealing
removed bottom panel.Has 2 screws on bottom.take belt off of idler. take 2 screws out of motor base.turn motor sideways& remove bolt from arm that holds idler. remove snapring holding idler. replace pully & reassemble in reverse. Thank You Partselect for prompt shipping. A+ Rating
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from Pottstown, PA
Parts Used:
56000
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Socket set, Wrench (Adjustable)
The blower wheel was busted because somebody ran the dryer without the lint filter in. A cord and a fork were caught in it!
Fairly easy to repair once I figured out how to get it apart. The amazing part of this was searching the web for the part. I found PartSelect, ordered it at about 2pm Eastern time and the part arrived the next day! I will definitely use this service again.
1 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Russell from Alexandria, KY
Parts Used:
LA-1003
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Install new latch
Just snapped the new plastic latch into the hole (the hole was there because in trying to extract the old latch, it fell into the inside of the door). Took two seconds. Order to arrival of the part took only 22 hours!
1 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
april from lexinton, KY
Parts Used:
61927
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
dryer not heating up
removed old element, relaced with new element , thermostat dryer works better than it has in along time
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Bonnie from Dexter, MI
Parts Used:
WP56170P
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Screw drivers, Socket set, Wrench set
Dryer started squeaking and eventually stopped tumbling
First I unplugged the dryer and turned off the gas. Pryed up the top of the dryer at the front corners to free the front panel. Removed the two screws at the bottom front of the front panel. Then disconnected the three electrical connections for the door button. Put the front panel to the side. Then took out lint tray and then removed four screws that hold the lint blower piece and put it aside. Then I could see the motor and the idler assembly is on the back of it. If you have a camera take a picture of how the belt is on the pulley. If not you can draw a general idea of the direction. I reached back and slipped the belt off the idler pulley. Removed two screws from the front bottom of motor fork .Removed two screws from a small electrical hook up thats on the front of the motor and removed it. At this point I could just slide the motor out. With a rachet and a regular wrench I removed the small bolt holding the arm on. Put on the new arm. Slid the motor back in and reconnected the belt. Put everything back together in the same way. Yeah it works. I am a 58 year old woman and this job required no brute strength. Don't be intimidated its really not that difficult to fix it yourself.
3 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Philip from Swansea, IL
Parts Used:
W10169313
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Socket set
Dryer Didnt Turn On
First - I did some research on line as to the possible problem with this dryer.
I had already taken the front apart before, so I knew what was needed to remove the door and front.
Remove the 2 screws that hold the dryer door in place with a Phillips screwdriver. Remove the two screws on the opposite side of the door also. Place the door out of the way. The front panel of the dryer now tilts forward. The front panel sits on two clips, tilt forward and lift out of place. The door switch has two prongs that hold it in place, pinch the prongs and the switch slides out. Disconnect the two wires on the switch and connect the wires to the new switch. The new switch slides into place. I tested the new switch before I put it all back together. Took me no longer than 15 minutes.
25 of 557 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the TGA600
121 - 135 of 218