LG8209W2 (PLG8209W2) Amana Dryer - Instructions

Door switch was very easy to replace as it simply snaps in for the outside and you just clip on the two control wires that already have clips on them.

Changed, got in aimed wrong direction-best to take a digital photo before you disassemble. Overtightened bolt and nut in assembly, it seized. Attempted to drill/grind it off, should have removed motor. Drill skipped up into motor windings. Could have replaced dryer, decided not, fixed by ordering motor, mount, nut and bolt and new belt idler. Reassembly was a snap till the gremlins hit again and I lost one of the drum glides. After a trip across town, I reassembled and it was good to go. Disassembly, use a screw driver to pry up the top, use the nut driver to remove upper front left and right screws, lift front forward and off bottom hooks. You have to release the wiring harness, it has four connectors. Use a sharpy marker and write the wire colors next to the plug-ins connectors you pull gently off and set the door aside. The second wires are two wires for the inner assembly which again need to be marked for color and then pulled loose. Pull them through the plastic hold down so they're out of the way. Use nut driver to remove four screws from inner drum holder, pry gently off dryer blower. Reaching around both sides of the blower housing find the belt tensioner, pull it to the right, push the belt out of it. Lift the drum out, up slightly over the back rollers. Set aside. Use the nut driver to remove the screws into the base holding the motor mount down, now lift the motor/blower assembly forward and pull gently loose from the dryer vent pipe. Set it up where you can work on it. Using the nut driver, take the screws off the blower housing, use a vise grip to secure the motor and use a 7/8 inch turning counter clockwise to remove the turbine. Use the nut driver to remove the screws holding the turbine housing in place, pop the motor clips off. Pull the motor off and remove the nut and bolt of the belt idler assembly using a wrench on the back and a socket wrench on the other side. Reverse order to reassemble, when tightening the idler arm tighten it to where you feel it stop but not any further. Put the belt around the drum again, get it in the previous location on the drum, feel around the drum to make sure belt isn't twisted, bring belt in from the back between the idler wheel and the vent pipe in a loop (Make sure the belt is behind the tension spring rather than in front), Tip the idler arm upward, use the other hand to slide the belt loop up over the motor pulley. One final note is this being a Maytag you might write these direction on the inside of the front panel for next time.

Took dryer apart, and found that the idler arm pulley was in pieces. Ordered the replacement from Partselect.com. Received part very promptly. Decided to also order a new belt, and that arrived in a very timely manner also. Put the parts in, and assembled the dryer. This was for my 90 year old grandmother, and she is ever so pleased that it is up and running again. Completed the repairs for about $50, and saved big money by doing it myself versus a service call, that would have boiled down to replacing the unit for the price it would have cost to fix. Will use partselect in the future for all my appliance repairs, as they offer a great selection of parts for all different appliances. Very pleased with satisfied with quality, and service from Partselect.com

I went to RepairClinic.com & FixYa.com for some great advice. I searched the internet for the parts. PartSelect.com was the most inexpensive. Delivery was good. Using the repairman's manual I found on the internet I followed the steps to remove each panel, in order. The wiring was the most bothersome, but okay to resolve; write it down and pull it off! I don't think the rollers, in the back, were bad. The tension idler was extremely worn. I tightened the tension idler bracket at the base. I did need to use an O-Ring Spreader to get all the rollers off and on. Although there were more panels to remove than older models, it was easier! Wrap the belt around the drum before reinstalling. The belt will loop around the drive & tensioner relatively easy. Replace the rubber seal around the drum & replace all the panels. Things are quieter now than I can remember in a long time.

Removed all of the front outer bolts holding in the lower plate, front door assembly, drum outer frame and drum. While removing the outer sheel there are colored wire connections that activate the linterior light and door sensors in which I marked the interior sheel with a marker so I knew which wire went where. Before removing the drum I drew a sketch on how the belt is ran thru the pullys and around the drum, so I would have no problem reinstaLLING IT.The rooler bracket was easily removed with a socket wrench and the retaining wring was pried with a pliers. Reinstallation of the shaft, roller and ring were as simple as removal. I then cleaned the entire interior and lint basket for optimal performance. The most difficult part is pulling the belt back around the drum, but still not very difficult. Finally I reattached nall removed parts as they were removed and I now have a like new dryer for about $20.00 vs, buying anew one or repair fees costing Hundred$ OF DOLLERS.
Thanks Partsselect.com Again!

Replaced glides and assy idler pulley cleaned all parts fron dust and debree, vaciumed heating eliment to remove all excess lint and wool to make sure I did'nt have a fire in the lower unit.
Job was'nt all that hard just have to watch what you're doing.

1.Unplug unit
(gas model, did not shut off)
2. Remove bottom front panel-2bolts
3 Remove main front panel-2 bolts (no need to remove door)
4. Make note of wire colors on door switch and light, disconnect
5. Remove 3 screws that hold air duct assembly(that lint filter rests in) then set main front panel aside
6. Remove lower air duct (to blower motor)-3 bolts
7. Lift and tilt-up top lid/panel of dryer and wedge wood or ? (this will give you easy access and better light)
8. Reach back behind motor to move idler pulley and remove belt from motor & idler pulley
9. Remove 4 bolts and lift up and out front bulkhead frame that holds drum in place
10. Slowly pull straight out & slightly up entire drum
11. Remove circlip/retaining ring, washer, roller, washer and shaft assembly.
12. Vacuum entire unit
13. Light lubricant on shaft when reinstall in reverse order.

Snap ring pliers and a mental note of how the belt is routed on idler will prevent unwanted profanity.
This is an inferior/substandard unit before Maytag bought them. Spend the money and replace both rollers with new shafts (about 50.00). I have spent over 140.00 in parts to keep this unit running (less than 8 years old). So do the math before you start pouring money into this model.

Early in the life of my dryer, the Cylinder Seal came out. For the past two years I put off buying the part. When it came in, I p[opped the top of the dryer, removed the two screws holding on the front panel, and pulled the Cylinder of the back wall of the dryer. I then placed the seal in the right spot, glued it down and reassembled. About Fifteen minutes of work and a cheap part, and now my dryer dries a l;oad of clothes in an hour instead of three.

Unplug the dryer. Remove bottom panel by removing the two retaining nuts. Unplug the motor cable connections. Remove the blower unit. Remove the two screws holding the motor down. Release the belt by slipping it off the tension pulley. Slide the motor out carefully.

I had to replace the idler pulley shaft. The pulley had scored the shaft and was digging into it causing the excessive noise. Reinstall the new shaft and pulley. You will need to remove and re-attach the retaining ring.

I took the opportunity to then blow out the motor unit. It was filled with lint. I then decided to replace the original belt.

You need to unscrew the rear retaining clips and use a putty knife or (I ended up using a small tire tool) to lift and separate the top. I then slide the belt up to the front of the drum. I unscrewed each bolt from the drum and removed the belt at each corner. By doing this it kept the drum aligned with the unit. Then just reverse the process to install the new belt.

Re-install the parts in order of removal. Done. Total repair took about 45 minutes. Would have been quicker except I forgot to re-attach the power clip to the motor and had to remove the unit again.

Noise is gone, dryer runs like a champ, hopefully for another ten years.

All you need for a Maytag is a snub nose Philips screw driver. The screws on the front panel are at the bottom angled down, so a regular length Phillip's won't work. Just unscrew the 2 screws, then lift the panel up and out. Careful not to pull out too far, there are 2 wires attached to the switch. The replacement switch is NOT an exact copy of the old one. My Maytag is over 30 years old and it only had 2 prongs on the switch. The new one has 3. Don't let that throw you. It is the same size. Just attach, 1 wire to the bronze connector & the other to the silver. Push the switch into the door opening, re-attach the door. Total time 20 minutes. Saved well over $100 in a service call. Anyone with an IQ above freezing can do it.

My gas dryer would run with heat for 5 minutes in all settings, but kick off and not heat again. Timer would not advance in autodry. Thought it was the cycling thermostat, so replaced that, but did not solve the issue. Ordered the coils, and cleaned out heavily clogged lint from bottom of lint trap, especially right above the fan motor at the bottom of the trap. Received the coils, opened the top and front, took out drum, and replaced the coils. The replacement took less than 2 minutes. Be careful putting the drum back on to make sure the felt is not caught inside the drum. You can give it a spin to make sure. Wear gloves, as I cut myself up pretty good on the edges of the dryer body. The inside of my dryer looks like a crime scene! Anyway, I put it back together, and it runs great. Solved the timer advance issue in autodry, and the heat kicks on and off when it is supposed to. Good luck! Thanks Part Select!

took 2 screws out and replace new coils

watched video for Each Part

I removed the two spade connectors and then removed the two 1/4" hex screws. I then simply removed the defective unit and replaced it with the new on and re-installed the two screws and wires.
This was not the problem though.
I turned out to be the solenoids on the gas valve.

Propped the machine up in the front, removed the front panel, the door assembly, and the front drum support. Use a Sharpie to mark wire positions. This will help during re-assembly. To get the drum out, you first have to remove the belt from the motor pulley. Drum slides right out. You will need snap-ring pliers to remove the pulley from the idler arm. I also replaced the drive belt because it was cheap, and always a good idea to replace it when you are this far into the machine if it is a few years old. Re-assemble in the reverse order of disassembly. An easy fix for the average do-it-yourself person.