ALG643RMC (PALG643RMC) Amana Dryer - Instructions

Had to figure out how to open the dryer - bottom screws in front and work up, removed the drum and found the fan blade was broken. Had some difficulty removing the fanblade from the motor shaft but after that the new one was easy to install. I did need help to place the belt and drum back into place. as one person has to hold the belts on the pulley while the other adjusts the belt while putting the drum back into place.

unplugged power cord, pulled timer knob off of stem, removed screws at rear of control panel, swung top of panel forward, LEAVE WIRES ON TIMER, used screw driver to release timer lock tab, turned timer to unlock retaining tabs, NOW REMOVE WIRES ONE AT A TIME AND PLACE ON CORRESPONDING TAB ON NEW TIMER, install new timer by placing tabs in openings and turned to lock in proper position, making sure lock tab snapped into place, put panel back in position, replace screws, replace knob on timer stem, plug power cord in, test cycle for operation,CONGRATULATIONS, it works!

Unpluged dryer from outlet, disconnected vent, positioned dryer on side, removed screws from bottom panel, pulled pannel away from dryer body to gain access to motor. Disconnected drum belt from motor pulley, disconnected wire harness from motor. Removed motor mounting bracket assembly and placed entire assembly on floor. Removed clamps and blower assembly from old motor, installed new motor and reassembled. Very easy project, hardest part requires some trouble shooting knowledge to determine the exact cause of problem.

I followed the instructions found on this site. The hardest part was figuring out how to release the clamps at the front of the dryer so I could remove the top.

The key was to unbolt the clamps at the back of the dryer first, then to use a putty knife to release the two clamps at the front of the dryer that hold the top to the front.

The rest was easy by following the steps already listed on this site and removing the two front pieces, then the drum and replacing the parts. Putting it back together was simple since I placed things in order and had taken pictures with my cell phone as I went through the process.

The time I took, included vacuuming the inside of the dryer thoroughly. Now it runs like new.

At first i thought i had to buy new dryer, because i did not know what to do.I said, i never done this kind of repair before, well i put everything apart and notice that the idler pulley was worn out, then i said this is something that i can fix it if i get the part. I made several calls and couldn't find it. so went in internet and found it with you.

popped up top of dryer -- With pliers squeezed clips on inside of latch - - with screw driver pryed latch out -- just pused new latch in.......... Thanks to parts select for sending part sooo fast.. wife was happy.. Thanks, Dale

First I unpluged the dryer, removed the two screws from the bottom access panel. I used a small socket to remove the screws securing the limit stat to the burner chamber, nut driver was too long.
I installed the new limit stat with the two screws and attached the two leads. Plugged in the dryer and conducted a test run, burner ignited. I turned the dryer off and replaced the access panel.

Door switch was very easy to replace as it simply snaps in for the outside and you just clip on the two control wires that already have clips on them.

watched video for Each Part

Replaced the two drum rollers and the tensioning arm roller. NOTES: 1. There are two drum rollers, the diagram seems to show only one. Recommend replacing both drum rollers and the support bracket shaft assemblies since the shafts might be scored. 2. The tensioning arm roller was actually much worse and frozen, so once you are in it is best to replace ALL three rollers. 3. I also replaced the belt since it was worse for wear from the frozen rollers. 4. The PartSelect video for the procedure is for the Whirlpool branded version of this dryer. The internal parts and construction are identical, however, the initial steps for opening up the dryer are different. On the Amana the top also tilts up, but is held down by two bolts, and not just the spring clips. Steps are: a) Remove bottom kick plate which is held in by two bolts on the lower front edge. b) remove the retention bolts that are now exposed on the front panel and remove the front panel by pulling it down from the top spring clips. c) Unbolt and remove the front drum retention panel. d) The two bolts that hold down the top can now be removed and the top panel tilted up so the drum can be lifted out after the belt is loosened. The whole process is very quick and easy. Only tricky part is fumbling around behind the motor to move the tensioning roller and arm to remove and re-install the belt. Also, I had cheap spring clip pliers so I was fumbling with the spring clips that hold the rollers on their shafts.

I watched the repair video and followed the instruction given to replace the belt. The instructions were easy to follow and to the point. The one thing that was not covered was to vacuum the interior prior to closing the dryer up.

All you need for a Maytag is a snub nose Philips screw driver. The screws on the front panel are at the bottom angled down, so a regular length Phillip's won't work. Just unscrew the 2 screws, then lift the panel up and out. Careful not to pull out too far, there are 2 wires attached to the switch. The replacement switch is NOT an exact copy of the old one. My Maytag is over 30 years old and it only had 2 prongs on the switch. The new one has 3. Don't let that throw you. It is the same size. Just attach, 1 wire to the bronze connector & the other to the silver. Push the switch into the door opening, re-attach the door. Total time 20 minutes. Saved well over $100 in a service call. Anyone with an IQ above freezing can do it.

Removed bottom front panel by two screws. glide brackets at about 8 and 4 o'clock positions, with screws coming in from the back. The replacement glide bracket and two drum glide will be needed. I drilled out the screw holes and used the original screws because replacement screws were too short and the screws go in from the front on the replacement glide bracket. You will need to slightly raise the front of the drum to install the glide brackets correctly. the reinstall the front cover.

(Used joe From Beacon Falls Instructions)
UNPLUG THE DRYER FIRST
1. There are two bolts on the back of the dryer that connect the control panel and the dryer. Remove these bolts with a socket wrench and their brackets. Set aside.
2. Lift up rear of dryer top a few inches to locate two metal flanges on the front top of the dryer. Lower the back side. Now on the front of the dryer, insert the flat head of a large screwdriver (cover flat head with rag to prevent scratches) where the flanges are located and pry upward, one side at a time. It does not take much pressure until the top “pops” open. Repeat prying motion on other side of front dry to free the top.
3. The top of the dryer is now loose and can be slid backwards enough to see down the front of the dryer. Locate two screws (one on each side) inside the front panel a few inches down. Use the same socket size with wrench to remove these two screws.
4. Notice there are three wires that connect for the light on the right hand side. With care, these can remain attached. Alternately, take the time to write down the color and order and remove these now
5. Pull the front panel towards you slightly and lift up. The front panel will now come free and can be set aside. If you did not remove the wires, the front will need to be propped up close enough to the dryer so that the wires are not ripped out.
6. Remove the three Phillips Head screws located inside the dryer drum that attach the Lint Duct Assembly. Pull out the old assembly. Vacuum out if necessary.
7. Insert the new Lint Duct Assembly and secure with the three screws.
8. Reattach dryer front and top.
9. Done.

My repair was very easy, the lint trap just comes assembled like when you buy the dryer. However, I had a hard time finding the dryer part at a store.
Part select had the item, they made it really easy to find online. The best part is how fast I received it! My dryer broke the day before thanksgiving (wednesday) i ordered the part that night and had it saturday morning! and thats with thursday being thanksgiving! I didnt even the pay extra for faster shipping! I would use them again and recommend them!