LED250 (P7762207W) Amana Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from REardan, WA
- Parts Used:
- 306436
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
door bent and when closed broke catch
remove front of dryer with door to get to the back of lach pin. replace front. seprate innor and out door pieces use pliers to remove catch spring clamp ot replace catch screw innor and outor doors back togfther and put tools away your done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Lincoln, NH
- Parts Used:
- 61927, WP40111201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
no heat and worn out belt
The repair went very well. The parts were a perfect fit and arrived earlier than expected.It took a little longer than it should have to do the repair because of my recent surgery I had my 11 year old grandson operating the nut driver taking the dryer apart install the parts then reassemble under my watch full eye. You could say it went so easy a fifth grader could do it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Geoffrey from GREAT FALLS, VA
- Parts Used:
- 56000
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
Delaminated blower fan
I followed the online video on PartSelect website. No other instruction necessary.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward A. from PHILADELPHIA, PA
- Parts Used:
- 56000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
I changed multiple parts on my dryer.
I totally disassembled the Dryer, and replaced the Guide Rollers, Blower Wheel, Idler Pulley Shaft, Idler Pulley, and Belt.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from Wimberley, TX
- Parts Used:
- W10169313
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door switch malfunction. Did not stop when door open.
Remove the front,2 screws. Replace switch. Only problem was holding front in position and starting screws at same time. Two person to finish.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Helen from Jacksonville, TX
- Parts Used:
- 306436
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
door catch on dryer broke
I only had to replace the inside one
I pulled the old one out .
And snapped the other one in
I pulled the old one out .
And snapped the other one in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Greenbush, MI
- Parts Used:
- 306436
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Dryer door catch was broken
Was extrememly simple. Just unscrewed the two screws at the bottom front of the dryer and pulled the front of the drayer out. PUshed the broken catch out and snapped the new catch in place. Reattached the dryer front with the two screws and was done. Less than 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- brenda from gonzales, TX
- Parts Used:
- 306436
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
pop it pop it in
used needle nosed pliers, squeezed the latch pop up push new one in. very simple anyone can do it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from POMPTON LAKES, NJ
- Parts Used:
- WPY54414
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Loud screeching from idler pulley
The round exhaust duct in the back my dryer can be removed simply by pulling straight out. This gives full access to the belt tension wheel. Slip belt off the wheel, remove snap ring with snap ring pliers, remove washer and wheel. Install new wheel, attach belt, and reinstall duct by looking right down the middle to line up properly. Dryer sounds like new again. 10 minute job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Manteca, CA
- Parts Used:
- 61927, WP40111201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
heating element had a short (broken heating coil) & belt had seen better days very worn after 14 years of service
remove front part of the dryer and rise up the top to remove drum to replace the belt. than remove two screws for the heating element piece of cake repair.
Was this instruction helpful to you?
Thank you for voting!
Belt noise/slipping even after replaceing worn motor assy
Unplug dryer. Remove lower panel.Remove dryer lent duct. Remove Thermostat fm fan housing. Remove Fan.Remove Fan housing. Remove Motor assy by sliding out, wires lay toward front, allowing room to replace idler pulley and spring. Use lock ring pliers to remove pulley from shaft. Grease pulley/shaft w/high temp grease [I used ultra-hi temp ceramic brake grease-can get in small packets at auto stores].Noise/slippage has all but stopped. Lesson: replace rear rollers and front felt/glides. Belt looseness also caused by worn rear rollers [smaller overall diameter from age]-even though they spin freely
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Amarillo, TX
- Parts Used:
- W10169313
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken prong
I began by removing the two screws at the lower part of the front panel. After removing the panel I was able to access and remove the broken switch which was located on the front panel. I popped out the old switch and replaced it with the new one, reattached the wires and put the front panel on and the jod was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pete from ANAHEIM, CA
- Parts Used:
- W10169313
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The door switch was defected
The door switch was easy to replace. It is located in the right bottom of the door and I popped out with my fingers. Follow the wire connectors from the old switch and remounted back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- maria from ROCHESTER, NY
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
dryer door would not stay closed.
I unscrewed the door catch and pried out with some resistance the strike part. Screwed in the catch and pushed in the strike. Closed door. Voila!! Back in business with assurance.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JEAN from KINSTON, NC
- Parts Used:
- W10169313
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The dryer door would not cut the machine off when it was opened.
Installed the new part. Worked great!
Was this instruction helpful to you?
Thank you for voting!