LE4207L2 (PLE4207L2) Amana Dryer - Instructions

I followed the instructions found on this site. The hardest part was figuring out how to release the clamps at the front of the dryer so I could remove the top.

The key was to unbolt the clamps at the back of the dryer first, then to use a putty knife to release the two clamps at the front of the dryer that hold the top to the front.

The rest was easy by following the steps already listed on this site and removing the two front pieces, then the drum and replacing the parts. Putting it back together was simple since I placed things in order and had taken pictures with my cell phone as I went through the process.

The time I took, included vacuuming the inside of the dryer thoroughly. Now it runs like new.

i am sorry i dont know all the technical term but here it goes, first I turned of the electrical breaker to the dryer, I unpluged the dryer and disconnected the dryer hose to the outside of home, I removed front dryer panel, remove front of drum panel, removed belt and found it to be worn, removed drum, removed the wiring connected to the back panel that had heating element inside, removed the back panel, removed the heating element inside the back panel and then reassembled unit. I had question whether or not it would ever run again, but it is working fine. Thank you for your prompt attention with sending the parts. i dont know if there was a different way to solve this problem, but i felt if there was an expection plate on the side of the unit, it would be helpful.

Opened things, saw lint buildup, cleaned inside of dryer, then cleaned entire vent discharge system, put new thermal fuse back, turned on dryer and heard metal to metal, opened dryer back up, saw missing glides (both gone). Ordered what I thought were 2 glides, 2 days later 1 showed, called and was told I didn't "update" when I changed order info (parts supplier cautioned to replace 2, should only sell in pairs) so then had to wait again for 2nd glide to show up. Replaced them today and noticed dried clothes are now cooler when finished. Will note in future if clothes are warmer, clean ductwork.

Unpluged dryer from outlet, disconnected vent, positioned dryer on side, removed screws from bottom panel, pulled pannel away from dryer body to gain access to motor. Disconnected drum belt from motor pulley, disconnected wire harness from motor. Removed motor mounting bracket assembly and placed entire assembly on floor. Removed clamps and blower assembly from old motor, installed new motor and reassembled. Very easy project, hardest part requires some trouble shooting knowledge to determine the exact cause of problem.

popped up top of dryer -- With pliers squeezed clips on inside of latch - - with screw driver pryed latch out -- just pused new latch in.......... Thanks to parts select for sending part sooo fast.. wife was happy.. Thanks, Dale

I opened the package and put it on the D stem.

I removed the Drier Door and removed the Front Drier Panel exposing the Gas Valve & associated parts. I removed two (2) screws holding the Gas Valve Coils in place & replaced the 2 terminal coil, then replaced the screws, Front Cover & Drier Door. I liked the results so much, I ordered the other Gas Valve Coil and will replace it also when it arrives.

Good trouble shooting information.

Replaced coils on gas valve.

After reading the many different common stories,I replaced both coils (m series).Very simply lifted up the top of driver,held by 2 snap springs and 2 lint vent screws.Removed front cover,2 screws and 2 bottom snaps,coils down on bottom left.r/r both coils,reinstalled covers and let there be heat!This website is a blessing!!

Had to figure out how to open the dryer - bottom screws in front and work up, removed the drum and found the fan blade was broken. Had some difficulty removing the fanblade from the motor shaft but after that the new one was easy to install. I did need help to place the belt and drum back into place. as one person has to hold the belts on the pulley while the other adjusts the belt while putting the drum back into place.

At first i thought i had to buy new dryer, because i did not know what to do.I said, i never done this kind of repair before, well i put everything apart and notice that the idler pulley was worn out, then i said this is something that i can fix it if i get the part. I made several calls and couldn't find it. so went in internet and found it with you.

Simple,I unplugged the dryer and took off the panel located below the dryer door. To do that unscrewed 2 small screws on the underside of the panel. Once that was off I used a flashlight to locate the heating element which was in the rear of my Amana. Using a socket attached to a screw driver I turned 4 screws out of the element and it was free. I brought the element closer and compared it with the new element and made note of the wire pattern. I plugged in the new wires I received in the box into the new unit and then one by one unhooked the wire leads coming out of the dryer. I reversed the above there it was...maybe 30 minutes!

The belt tensioner was the problem and the belt had very fine cracks in it so I ordered four parts: the belt tensioner, belt and the two drum rollers. I had to work to clean the fan and the LARGE dust bunnies. I'm writing this to encourage others to consider installing new duct work, mine was becoming a fire hazard. At a minimum clean all the duct work. Your dryer will work so much better. Thank you for your printable help!??

Removed all of the front outer bolts holding in the lower plate, front door assembly, drum outer frame and drum. While removing the outer sheel there are colored wire connections that activate the linterior light and door sensors in which I marked the interior sheel with a marker so I knew which wire went where. Before removing the drum I drew a sketch on how the belt is ran thru the pullys and around the drum, so I would have no problem reinstaLLING IT.The rooler bracket was easily removed with a socket wrench and the retaining wring was pried with a pliers. Reinstallation of the shaft, roller and ring were as simple as removal. I then cleaned the entire interior and lint basket for optimal performance. The most difficult part is pulling the belt back around the drum, but still not very difficult. Finally I reattached nall removed parts as they were removed and I now have a like new dryer for about $20.00 vs, buying anew one or repair fees costing Hundred$ OF DOLLERS.
Thanks Partsselect.com Again!

Using instructions from your website, I was able to remove access covers from my driver & find the pieces that needed to be replaced. It was a simple repair job & now my dryer is working properly again.