ALG331RAC (PALG331RAC1) Amana Dryer - Instructions

Super easy. 2 screws allows you to remove the access panel. One screw on the igniter bracket removes the igniter. Pull off the 2 wire connectors and plug into the new one. Test the dryer and close the access panel.

Unplug Dryer. Remove 2 5/16in hex screws fm lower panel,3 51/6in hex screws to vent duct. Remove 2 1/4in hex screws to thermostat. Remove 7 1/4in hex screws to blower cover and 2 5/16in hex screws holding base footings.Use adj. wrench to hold rear nut on motor shaft, use7/8in socket to remove fan frm motor shaft. Remove 3 5/16in hex screws holding fan housing to motor mount. Lift-up on spring tensioned belt pulley to remove belt. Pull motor & mount out [wires are layed toward front allowing removal]. Use 6in flat tip screwdriver to unsnap both front/rear motor clamps.Pinch plastic end clamps and remove motor electrical connector.Motor installation is reverse. For belt removal,remove 2 5/16in hex screws to door panel [unhook 2 wires to upper RT rear to door switch].Remove 4 5/16in hex screws to front bulkhead panel.Allow drum to sag IN PLACE [removal not required to replace belt],note belt location and slide old belt off and new one on
Replace Bulheald and door panel [re-attach door switch wires].Complete install by lifting belt pulley and feeding new belt into place. Hand rotate drum to ensure proper belt allignment and tracking. Replace lower panel. Vacuum interior as necessary. Parts delivered in 3days and fit perfectly.

I pretty much followed a lot of the earlier postings on partselect.com that provided encouragement to pursue replacing this part on my 17 year old dryer (sorry, money is tight these days and I prefer repair to $800 replacement).

I'd like to add that I borrowed a pair of snap-ring pliers from work which made removal and later securing of roller onto shaft much easier and probably avoided a lot of knuckle bruising and cursing.

I erred though in a couple of places during the replacement. Disassembly took about 20 minutes. However, when I re-assembled I had mistakenly already put the roller onto the shaft before trying to put the drum back in. That isn't possible so I had to remove (an initial groan but only a few extra minutes in the end) the roller from the shaft, then reposition the drum and then the roller back on the shaft.

I also decided to replace the belt while I was in there and I should have taken a picture or made a drawing of the belt route before I took it off since I was later left pondering how the heck to snake the belt onto the shaft and also the tensioner. A quick trip to the internet though showed me a similar route and reminded me how to route it.

I'd also like to add to be cognizant of the wires on the door and front panel when disassembling.

Anyone with any sense of mechanical ability and a little common sense ought to be able to do this repiar.

Thanks Part Select!

The repair looked simple enough until it came time to take the out wheel off. Because you can not hold the motor shaft(and the wheel screws on) it was necessary to remove the whole motor assembly and then grind the out shaft down, then use a small screwdriver to take the remaining shaft off.
I must say it was nice to recieve the part in as fast as I did we live in a very rural area and things like that are very hard to find

First of all I would not have done this if it wasn't for
your website. Using the schematics to figure out
the right parts was easy. It was also helpful in the
actual repair process. I have added your website
to my favorites in my browser. The parts arrived in 3 days and I live in Reno. Great Website.

M.B.

Being my lousy Maytag washer died THE PREVIOUS DAY, spewing water, etc. and I had rushed out and bought a new washer, I was determined not to replace the dryer (though I now am a serious NON_FAN of Maytag).

I disassembled the whole dryer and finally got to the blower wheel which was broken lose from the molded nut. I supposed something like a dime or penny got in there to shred it.

PartSelect's website allowed me to find the part in 5 minutes. It was on my doorstep the next afternoon.

Installation was straightforward BECAUSE I stacked all the screws and and labeled them appropriately. It took about 30 minutes to reassemble and the toughest bit was getting the drum in with the belt positioned properly.

First of all I think this was an assembly issue, cause it was a bit noisy since we bought it, but I dismissed it as a break in noise & it would go away over time, but of course it just got worst ontil it failed....
Anyway 1st thing I did was, stick a standard screwdriver between the top & front, to pop the top off, then used a socket wrench set to remove the 2 screws for the front panel assembly, ( **taking note were what color wire connectors went were 3 for switch "y,g,b" & 2 for light "yb & g"), then used socket wrench set to remove 4 screws for the front bulkhead, ( upon removal I now understood what the noise was all about, the lip of the drum was rubbing against the bulkhead & both cylinder glide brackets, wearing the drum lip & cylinder glide brackets, down to shards of metal, rasor sharp, Both brackets were wore in half & bulkhead damaged ), then I removed the shards from the drum & used the hamer to dull & round a smaller drum lip, then I removed lint trap holder from bulkhead, ( since I had it apart I took it outside & cleaned it with my power jet hose attachment ), then I removed missalined & Damaged cylinder seal, srcapped bulkhead clean with standard screwdriver, applide goop glue to bulkhead & new cylinder seal, then applide new seal & let dry overnite, in the mean time I removed both damaged (the other half), cylinder glide brackets, used the old gliders & pads, ( they were not damaged, " LIKE NEW"???), attached them to the new bracket, then attached the 2 cylinder bracket assemblies to the bulkhead, then I used metal tape (several layers on both sides of bulkhead) to fix the damage caused by the old missalined seal & drum lip.... Then I re-assmembled lint trap holder to bulkhead, & re-assembled bulkhead to dryer, then attached the front, ( see above**), then popped the top into place... Now we have a GOOD QUIET dryer

I disconnected power and vent hose then tipped dryer on its back. I took off lower panel and door ,disconnecting wires to door and light and hanging them over the side,i then removed the front plate and felt seal the plastic fan shroud and lint trap come out as one piece along with the front plate.when i could look down on the drum,standing on the left side ,i disconnected the screw connecting the top plate to the left side plate allowing the top to gain a little play,this is the amount needed for the drum to be removed,pull belt tensioner slightly as to release tension remove the belt from motor shaft.At this point remove drum and set aside,the lower felt ring and support rollers will be exposed as well as tension spring and tension roller,i used a mirror and guided the snap ring pliers into place on the tension roller,At this point pull on rear felt ring it may come loose easy ,if not work some adhesive remover into the cracks where the glue is and keep agitating it ,eventually the glue will begin to release and more and more of the remover can get in washing the felt ring off,clean real good after using remover soap and water and allow to dry ,apply a thin ring of high heat adhesive smooth out to spread even all around when it becomes tacky begin applying new felt ring,while this adhesive cures perform the same procedure on the front panel and its felt ring while these rings are drying into place undo snap rings and pull support rollers out and replace in like order replacing thrust washers and snap rings if you damage them ,the roller on the tensioner is more tricky but if you use a mirror and a light it is easy to sneak in there lastly when preparing to reassemble and drum and belt are in place just before you replace the front panel it is prudent to replace the neoprene slides,reassemble front plate and ensure that the felt ring lines up and goes in evenly all the way around re-attach top left corner ,reinstall door and wires as well as bottom plate this will conclude the procedure i learned all of this the hard way i should have just replaced all the parts at once i was in that machine 6 different times Daniel 2017

As it turned out, the felt was only part of the problem. The guide bracket had been cut thru by the drum. This all started when a golf tee got stuck in the drum area. It took very little time to destroy the guide bracket. Dryer was built by Whirlpool. Parts are built to the bare minimum. These appliances are designed to break in a couple of years. There is no doubt about it. I installed the new guide brkt, glued the new felt on and put it all back together. The job is pretty straight forward but you need to be mechanically inclined.

The Dryer is about 25-30 years old. I replaced the motor due to overheating, while I had the dryer disassembled I decided to change out the idler pully wheel and the drum support rollers. This was my first time changing out the motor. Surprisingly, the blowerfan blade came off the shaft of the motor very easy. I was concerned about the age of the dryer and was anticiapating this could be a problem fortunately, it came off very easy. Removing the old motor was easy. The only issue I had was seating the new motor in the correct position. I felt that the motor was not in the correct posiotion however, I was not sure being that this was my first install.
After trying several times, rotaing the motor back and forth (side to side) within the motor holding end brackets the motor fell into place and I was able to put on the end motor clamps on correctly. The drying is now working.

Viewed video on website, however did not match model but put me in the ball park for an overall view. Thank goodness I had the insight to order the pully with the belt. I believe the pully failed first causing the problem with the belt. Recommend replacing both any way while you have it apart.

Had to lay dryer on back. Cause it didn't have a back cover had to take the front door off and go in thru the front. Had to take the vent off. Had to use scotch tape to hold the belt in place while I got it on. It would have been a lot easier if they had a back cover. I only hope I don't have to do it again as it squells a bit on start up. Bill

I first removed the front panel and door on the dryer using a 5/16th nut driver. I needed to disconnect the light and switch to remove the door. I raised the top lid of the dryer to expose the drum. I rmover the fan schroud and lint filter by removing 4 5/16 screws with the nut driver. I disconnected the belt from the idle tension pully and removed the drum. The drum support rollers were visible on the back frame of the dryer. I removed the bad roller using snap ring pliers. After cleaning the roller support shaft and lubricating the shaft with grease I replaced the drum support roller and secured it with the snap ring. I also replaced the dryer belt although it was still workiing. I reasembled the dryer after giving the inside a cleaning with the shop vac. The hardest part was getting the belt secured with the tension idle pulley. When assemblying the fan schroud make sure it is snug against the fan so it doesn't leak. Replace the top and front door and cover connecting the switch and light. If you get the switch wires correct the dryer will run with the door shut otherwise reverse the wires.

Removed the bottom panel. Removed door to dryer and disconnected the door switch. Removed the top of the dryer. Now I had access to the drum basket of the dryer. Removed the belt and took drum out. The idler was accessible and easy to replace. I replaced the other drum support rollers. These were a bit difficult when it came to removing the clamp pins holding the rollers. Once you get one the other is easy. Reassembly is relatively easy and quick. Dryer no longer squeals, runs nice. I felt really good.

I took out the 2 screws on the bottom of the front cover, pulled out at the bottom, disconnected the 2 wires for the front door and removed 2 screws on the inside top of the front panel and removed. The top of the dryer then flips over. I then tool out 4 more screws and took out the drum. I totally cleaned out the inside of the dryer and then took the oring pliers and removed the oring that held the roller on the belt tension bar and replaced it with the new one that you sent me. I put the drum back in and put the belt back on the new roller, I put the dryer back together and now I have a good dryer that will last another 10 years.