LEC50AW (PLEC50AW) Amana Dryer - Instructions

Remove the 2 screws at bottom of front panel, remove lower panel. Then remove the two screws at bottom of front door. Lift door forward so spring hooks can disengage from the top panel. remove door, disconnect the 5 wires to the door latch and light. remove the two screws at top of dryer to lift up top panel. Remove 4 screws at the front holding the drum. Disengage the belt from the tension pulley and remove drum. Replaced both roller wheels at the rear of the drum( one was broke). Then remove the screws (about 6 holding the plate in front of the blower wheel. Use a wrench to hold the nut at the back of the motor and a scocket wrench to remove blower wheel. (The Blower wheel was broken from the shaft and was spinning freely). Then do it all backwards to re assemble. i spent more time cleaning the lint from the inside than I took making the repair!

Shut off or unplugged dryer for safety.

Slipped thin blade putty knife up under bezel of switch to unlatch from the panel and pulled forward to remove the swwitch from the dryer. Unplugged the quick connect terminals (3) from the old switch and plugged them onto the new switch. one of the terminals had gotten quite hot and darkened the insulation so it was replaced with one that was supplied with the switch. that was a cut, strip, crimp process. Placed the new switch into the panel and snapped into place.

Not too difficult. Take out of box, insert into dryer slot.
Done

Dryer would only tumble for ~15 min then stop. During this time it would be really loud. Turns out to be a bad Motor. To replace 1) Removed bottom kick panel by removing 2 screws. 2) Then removed upper front cover by 2 additional screws. 3) Disconnected thermostat (marking location of wires on paper). 4) Removed blower housing (3 screws)undid the rib belt from the drum by pushing the pulley wheel up so the belt could be loosened and removed from motor. 5)Removed the front cover of the dryer opening by removing 2 screws. 6) Lifted up and then puled it out to expose the drum. 7) Removed the drum w/belt from the dryer exposing the motor. 8) Removed 2 screws from the motor and disconnected the plug from it. Slid it all the way out. 9) Need to remove (3 screws) the metal faceplate from motor to access the blower wheel (plastic). 10) Unscrewed the plastic wheel and removed 2 screws to remove the motor from the frame. reversed the process for reassembly. Sounds tougher than it really was - only took 30-45 min. Suggestion - write down on paper location of any wires you disconnect - makes reassembly very easy. Also recommend vacuuming any lint in the dryer while it is completely accessible.

remove bottom section under door 2 screws remove door 2 screws remove switch by squeezing tabs install 2 new female ends on wires supplied with switch . put switch back in plug in wires .

1-Unplugged drier
2-removed lower panel-(2)-8mm screws
3-removed intake from fan-(3)-8mm screws
4-removed dryer's front panel-w/door assembly-(2)-8mm screws. (note there is a door switch you will need to disconnect the wires and remember which terminals they go to.
5-remove the front drum support-(4)-8mm screws
***** at this point the drum is exposed *****
6-reached under the drum pulled the tensioner to relieve tension on belt, then dismounted the belt from only the tensioner and motor shaft; leave the belt on the drum!
7-pull drum toward you and forward about 3-to-4 inches, this exposes the drum rollers.
8-use a screwdriver and pry-off the retaining clip on the end of the roller's shaft and remove the roller.
9-remove the roller support-(2)-8mm screws
10- reinstall new roller support
11- apply a light coat of disc-brake hi-temp wheel bearing grease to the roller support shaft, very light!
12-install a new wavy thrust washer, new roller(note they will say "front" on the side that should face you. Don't mount it backwards!
13-install the outer thrust washer and the new retaining clip; use a flashlight for this part!
14-repeat for the other drum roller.
**** while you have it apart use a vacuum to remove lint from every where you see it; it is a fire hazard!
**** if you think you need a drive belt now is the best time to change it *****
15- re-assemble the dryer in the reverse order, don't forget to re-install the drive belt and be careful not to pinch the door switch wires.
16-re-plug the drier and test

Replaced the recommended drum rollers, belt and tensioner, light bulb. Found repair manual online (bit of a hunt)made job easier still took 2.5 hrs. Then turned drum by hand no squeak. Turned it on and still squeaked. Isolated to motor. Replaced it (had to take dryer completely apart again but went quicker due to experience also had to disassemble the motor assy and rebuild. Took 1.5 hrs works like new now. The design of the dryer is not bad remove bottom front panel first, screws at very bottom of panel then two more screws are uncovered to remove front. It just lifts up and pulls out. then remove four bolts which hold front frame on (supports drum) all this has to be done to reach the replacement parts. drum wheels are held on by snap rings not the screws (real fun if you take them out) reverse to reassemble.

First I went to Maytag.com thinking it was best to go to the manufacturer for parts. Their search engine did not even recognize my part number. I tried every way I could think of. Then I just entered the model number in google and it sent me to the Partselect.com website. Diagrams came up and I chose parts from the pictures. The parts arrived in about 3 or 4 days and fit perfectly.

Determined that the 2 completely worn off front & rear drum seals were causing dryer to take too long to dry clothes.
Removed the front bottom panel first, then the middle panel and then the top panel. After removing the belt from the drum, it came out easily. Replaced both thermostats and fuse
just so they would be new in the unit.
Reglued the seals in place and waited til glue dried. Then reassembled everything back. Also lubricated the drum wheels. Everything worked and was quiet!

I first suspected the heating element or thermal overload had gone out due to lint buildup etc. from previous dry experience. I went into the lower portion (2 screws in lower front panel) of the cabinet and after checking other posts here was able to go to and remove the element assy. quickly from the left rear of unit (2, 5/16” hex screws). Using my VOM the element tested good, so did the limit switches in the element assembly and the warm air duct. I vacuumed this area while there and made sure the duct was clean. Checked belt & tensioned. The problem must be up in the control panel section. I pulled apart the control panel (2, ¼ hex screws trim& 3, ¼” hex screws panel face) I found the orange lead push on connector from the timer switch to the heat selector control had overheated and burnt the wire in two had also burnt the terminal on the timer. Trimming back the discolored wire I crimped on another connector. My new timer came overnight as promised by PartSelect. The job was $20 cheaper than just the part locally that would have had to be ordered, plus shipping, plus tax.

Easy repair and done all from the front. Turn off the power at the breaker. Make sure the power is off. Remove 2 screws holding on the lower panel. Then remove 2 screws holding on the door panel. (Pay notice to the order in which the 3 door wires will get re-connected. The 2 light bulb wires probably can go either way.) Then remove 4 screws to a large bracket that supports the front of the drum. (Set these parts aside as you take out the screws.) Then remove the 2 screws from the top panel. Reach in under the drum and release the tension off the belt. It's easy to release, but sorta mind boggling to put back on. Maybe practice that once while it's fresh in your mind. When the belt is off the motor pulley, then lift out the drum. Vaccuum out a lint blanket if you have one. You'll see the 2 drum support rollers and the belt tensioner roller. I didn't know which was squeaking so I replaced all 3. Same method, use ring pliers to take off the retainer ring, remove old, wipe off dust, install new rollers, replace ring. Note the washers are different so put them back on in the same order as removed. Make sure the gasket on the lint assembly gets tucked nicely into the blower housing when you reassemble. Easy repair. If you do pull the dryer away from the wall, replace your flexible exhaust vent with the fire resistant aluminum version.

I believe the best procedure would be to start at the very bottom of the machine - there are two sheet metal screws in the bottom panel. Remove the bottom panel.

Now, there are two sheet metal screws at the bottom of the front door panel that need to be removed. Remove front panel by pulling down to dislodge from plastic pins aligning it to the top panel.

Now the air duct assembly is accessible. From outside machine remove two sheet metal screws holding lower air duct frame. From inside the dryer opening, remove three screws holding the upper frame. Remove old air duct assembly and vaccuum machine.

New air duct assembly is in one piece, so only three inside screws are needed to support it. Make certain the screws are seated well or clothes could get hung up on the screw heads. Reinstall front door panel and bottom panel.

Doing it this way should make the job around 20 to 30 minutes.

1. Remove bottom sill plate with two screws
2. Remove door, watch for the wire.
3. Remove tub retaining "ring" 4 screws
4. Pull tub forward
5. Pull off the old support roller using the snapring pliers
6. grease the new roller and pins (do both sides)

Reverse it and put it back together and its good as new!

First I unplugged the dryer, then I removed the bottom front panel. Then the door I marked the wires to the shut off switch on the door and removed the switch from the door. Next was the lint screen housing and duct work that goes to it. Then I had to reach under the drum and take the belt off of the motor pully and tensioner so I could remove the drum. I removed the drum. I then marked all the wires I had to disconnect. I took the fan housing front panel off. I held the belt drive end of the motor shaft with the pipe wrench, i could have used an open end or an adjustable wrench also. I used a 7/8 six sided socket on the plastic fan nut on the front of the shaft so that if it was hard to loosen I would have a better chance of not rounding the nut. I removed the fan and the back of the housing, unplugged the motor, and removed it. The clips that hold the motor to the motor bracket are a little tricky, I used a screw driver to remove them. I then replaced the motor and put everything back together. One hint you should know is to make sure you mark the drum front so when you put it back in you get it right the first time. I fits in both ways and will go back together but it won't turn free and you'll have to take it all apart again. I tried it by hand both ways and was able to catch the mistake before I put it all back together, but I could have put it together wrong.

The parts to replace were mounted to the rear wall of the dryer and only the front pane is removeable. With the panel removed the drum had to be pulled carefully straight out. The belt and tention arm were difficult to reposition. Since you have the appliance apart replace both roller and roller support brackets one of which you cannot see from the front. Throughly vaccum all lint and roller wheel debris . If you have an air compressor take the time to blow out the motor . Make sure to rig a device to hold the tention arm back with the belt correctly aligned while sliding the drum back into place. PARTSLECT is great , easy to use and suggests other parts I may not have thought of and quick . Parts were here in 2 days standard shipping. I was in the dog house for putting this off too long. My wife is happy so I'm happy.